ملخص المحتوى في الصفحة رقم 1
PSR1212 Digital Matrix Mixer
Installation & Operation Manual
ملخص المحتوى في الصفحة رقم 2
ii ©2002 ClearOne Communications, Inc. All rights reserved. No part of this document may be reproduced in any form or by any means without written permission from ClearOne Communications, Inc. Printed in the United States of America. ClearOne Communications, Inc. reserves specific privileges. Information in this document is subject to change without notice. PSR1212 Installation and Operation Manual ClearOne Part No. 800-155- 001 Jan 2007(Rev. 7.1) Technical Services Group ~ 1-800-283-5936 (USA)
ملخص المحتوى في الصفحة رقم 3
iii PSR1212 Installation and Operation Manual Table of Contents CHAPTER 1: Introduction . . . . . . . . . . . . . . . . . . . . . .1 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 . . . . New Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Professional Services Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 . . . Product registration . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 4
iv CHAPTER 3: System Configuration . . . . . . . . . . . . . . . .21 G-Ware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Creating Floppy Disk Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Installing G-Ware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Site Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 5
v CHAPTER 5: Operation . . . . . . . . . . . . . . . . . . . . . . . .65 Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Signal Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Document Compare Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Print Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 6
vi Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
ملخص المحتوى في الصفحة رقم 7
CHAPTER 1: Introduction Product overview Congratulations on purchasing the PSR1212, a highly advanced twelve-by-twelve digital matrix mixer with audio processing. It utilizes an internal macro language and 32 user-definable presets to quickly adapt to a variety of sound reinforcement and room-combining applications in auditoriums, stadiums, theatres, gymnasiums, hotel/convention centers, conference rooms, training rooms, and boardrooms. The PSR1212 facilitates local and remote PC setup and diag
ملخص المحتوى في الصفحة رقم 8
Introduction ~ New Features 2 New Features • Virtual references. The PSR1212 now features four user-definable virtual references. These references can use multiple signals as the PA Adapt reference point without sacrificing an analog output. • Front panel gain and mute control. Now gain and mute adjustments can be made from the front panel. Using these controls allows you to make quick volume and mute changes without connecting through G-Ware. • Safety Mute. The new Safety Mute button on the ma
ملخص المحتوى في الصفحة رقم 9
Introduction ~ Professional Services Group 3 Professional Services Group If you need any additional information on how to install, set up, or operate your system, please contact us at one of the locations listed below. We welcome and encourage your comments so we can continue to improve our products and serve your needs. ClearOne Communications ~ 5225 Wiley Post Way, Suite 500 Salt Lake City, Utah 84116 Technical Support Telephone: 1.800.283.5936(USA) or 1.801.974.3760 Fax: 1.801.977.0087 E-mail
ملخص المحتوى في الصفحة رقم 10
Introduction ~ Unpacking 4 Unpacking Ensure that the following items were received with your shipment: ClearOne is not responsible for product ! damage incurred during shipment. You must make claims directly with the carrier. Inspect your shipment carefully for obvious signs of damage. If the shipment appears to be damaged, retain the original boxes and packing material for inspection by the carrier. Contact your Figure 1.1. Equipment included with PSR1212 unit carrier immediately. Controls and
ملخص المحتوى في الصفحة رقم 11
Introduction ~ Controls and Connections 5 C. s/tThese buttons scroll up and down through vertical programming options within a specific PSR1212 programming parameter or increases/decreases a numeric value. D. Esc. This button steps you out of a selected parameter or moves you up one level in the menu. When a parameter has been displayed with the arrow buttons [C], you can select it with the Enter button [B] to modify it. Then, you can step out of the menu with the Esc button. E. LED meter. This
ملخص المحتوى في الصفحة رقم 12
Introduction ~ Controls and Connections 6 Power is supplied through the RS-485 ports to the remote Control Panels from the PSR1212. This power is limited to a total of 300mA at 15 volts for each connector. Over-current protection is provided on the +15V pins to prevent damage in the event of shorting. External power can be provided to control devices when more current is required. See page 89 for maximum cable run distances when using ClearOne Control Panels. D. Control/Status Ports A and B. The
ملخص المحتوى في الصفحة رقم 13
Introduction ~ Networking 7 Networking Expansion bus The latency or propagation delay is The digital mix-minus expansion bus (RJ-45 LAN) is used to connect up to eight <1ms. PSR1212s (or XAP 800/400s and 16 XAP TH2 units), where the total number of microphone inputs does not exceed 64. The maximum distance between interconnected PSR1212 or XAP 800/400 units is 80 feet (24 meters). Connecting a XAP TH2 must not increase the cable length between two PSR1212s, XAP 800s and/or XAP 400s beyond 80 fe
ملخص المحتوى في الصفحة رقم 14
Introduction ~ Operational Requirements 8 Operational Requirements Power The PSR1212 automatically accommodates voltage requirements of 100–240VAC, 50/60Hz, 15W. Equipment placement The PSR1212 units are designed for installation in a standard 19-inch equipment rack. You can also purchase side panels for desktop placement. See Appendix D for a list of accessories. Environmental The PSR1212 can be safely operated in a room with varying temperatures between 32 ° F/0 ° C and 110 ° F/43 ° C. G-War
ملخص المحتوى في الصفحة رقم 15
CHAPTER 2: Installation The PSR1212 is designed for easy installation and setup. All connections are made through rear-panel connectors. This chapter provides instructions on making hardware connections, creating an expansion bus network, assigning device ID numbers, selecting the mixer mode, and using the front panel LCD menus. Hardware Setup The diagram below illustrates the typical connections that are made for a PSR1212 system. ClearOne Figure 2.1. PSR1212 installation diagram Technical S
ملخص المحتوى في الصفحة رقم 16
Installation ~ Hardware Setup 10 Expansion Bus In Out Figure 2.2. PSR1212 rear-panel connectors To connect the unit 1. Place the unit in a standard 19-inch rack and attach it securely. 2. If you are using a custom controller for control and status, plug it into the DB-25 Control/Status A or B port [D]. If you are using an external RS-232 controller, connect it to the RS-232 port [I]. 3. Wire the inputs and outputs to the PSR1212 using the provided three- The three terminals in terminal Phoeni
ملخص المحتوى في الصفحة رقم 17
Installation ~ Networking Units 11 Networking Units Expansion bus connections Using the Expansion Bus ports (RJ-45), you can connect up to eight PSR1212s or XAP 800/400s and 16 XAP TH2 units, where the total number of microphone inputs does not exceed 64. Make connections between units in daisy-chain fashion using the short RJ-45 jumper. If your units are further apart, use category five twisted-pair cable. The maximum distance between interconnected PSR1212 or XAP 800/400 units is 80 feet (24 m
ملخص المحتوى في الصفحة رقم 18
Installation ~ Networking Units 12 If the same device ID is Device IDs assigned to more than Once your expansion bus connections are made (and if you have more than one one unit on the E-bus PSR1212 at a site), you need to set up a unique expansion bus device ID number— a network, the Meter LED “ +12” network address— for each PSR1212 on the network. As shipped from the factory, all will flash red and the Mic LEDs PSR1212s are set to device ID 0. “ 1,” “ 2,” “ 4,” and “ 8” will flash green on t
ملخص المحتوى في الصفحة رقم 19
Installation ~ LCD Programming 13 LCD Programming The PSR1212’s front panel is intuitive to operate, thanks to its simple interface: a G-Ware software is 2x16 character LCD, menu buttons, and a peak-level LED bar meter. Although most required to complete of the PSR1212’s features are programmed with G-Ware software (see page 23), system setup. the front panel can be used for simple adjustments and meter monitoring. When power is applied to the PSR1212, the LCD panel will first read INITIALIZING
ملخص المحتوى في الصفحة رقم 20
Installation ~ LCD Programming 14 The five main menus are: System, RS-232, Meter, Inputs, and Outputs. All submenu items are arranged under these menus. Use the Enter button to select items and the s and tbuttons to scroll through menus and submenus. When the last menu item is reached, the display scrolls back to the beginning of the list. The Esc button allows you to back out of the menus. To adjust a parameter 1. Scroll to the parameter you want to adjust. Press Enter to select the parameter.
