PYLE Audio 9 Pyle Pro Mixer PYD 2200 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Specifications
PYD2200
Input Sensitivity/Impedance High 10kHz; +12/-12dB
Mic 1-2 1.5 mV/600 Ohms, bal/unbal Mid 1 kHz; +12/-12dB
Phono 1-2 3.0 mV/50K Ohms
Low
Line 1-9 150 mV/27K Ohms 100Hz; +12/-12dB
MIC Tone Control
Output Level
High
Amp 2.0 V/10kOhms 10kHz; +10/-10dB
Booth 2.0 V/10kOhms
LOW
100Hz; +10/-10dB
Record 150mV/10kOhms
Talkover Attenuation -16dB
Frequency Response 20Hz – 20kHz +/- 3 dB
PYD2200
S/N Ratio (at 1 kHz)
Mic >60 dB/1.5mV input
Phono >70 dB/3.0mV input
Line >80 dB/150 m

ملخص المحتوى في الصفحة رقم 2

Your PYLE PRO Series Performance Mixer Features and Controls: PYD2200 Mixer is a sophisticated control center, perfect for mixing sound from multiple playback sources such as microphones, tuners, CD players, turntables or the audio outputs from a VCR. This mixer is ruggedly constructed for home or professional use. Wide range volume controls permit you to adjust sound levels accurately to achieve just the right mix for playing through your speaker system or for recording. Please read this manual

ملخص المحتوى في الصفحة رقم 3

Presetting the Controls Before Use Connecting High Level Output Audio Sources Since sudden high output levels from your Pyle Pro mixer can damage not only audio devices connected to the mixer output but your hearing as well (especially if you are using headphones), please adjust Connect up to 9 such sources (tuner, cassette deck, CD Player, camcorder or VCR) to the input jacks the mixer’s controls BEFORE connecting AC power or turning on the unit. for Line 1 , Line 2(if not being used as Phono 1

ملخص المحتوى في الصفحة رقم 4

Using the Channel Input Gain Controls Using Headphones Adjusting the Gain controls for each channel permits you to fine tune the level of each of the audio Plug a pair of stereo headphones (not supplied) with a 1/4” jack into the Phones input. Using inputs, since input levels usually vary. Rotate the Gain controls clockwise to increase levels. After headphones not only affords you the opportunity to listen privately, but also enables you to monitor you preset the gain levels for each input, it i

ملخص المحتوى في الصفحة رقم 5

Adding Equalization to the Mix Using the Mixer Controls Turning on the Mixer These high, mid and low 3 band equallzation controls, permit you to tailor the tone frequency of the each channels inputs processed through themix. left in their center positions, the sound is 1. Turn on the output amplifier and temporarily set its volume to the minimum setting. unaffected. 2. On the mixer, turn ON the power switch. The power LED will illuminate. Using the Microphone 3. Turn on the audio input sources y

ملخص المحتوى في الصفحة رقم 6

Troubleshooting Your mixer should require very little maintenance. If you have problems, refer to the chart below for possible solutions. If you cannot solve the problem, contact a qualified technician for assistance. PROBLEM POSSIBLE SOLUTION Nothing works • Check the AC connection. Make sure the AC outlet is “live.” • Check the power connection to the rest of the system (receiver/amplifier, etc.) No signal from an • Check the control setting audio input • Check the connection between the mixer