ملخص المحتوى في الصفحة رقم 1
DIGITAL IO BOX
Owner’s Manual
V516420 R2 1 IP 20
E
100 CR Printed in Japan
ملخص المحتوى في الصفحة رقم 2
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instru
ملخص المحتوى في الصفحة رقم 3
Dio8_E_Body Page 3 Wednesday, February 28, 2007 10:21 AM ■ Precautions •Do not place a container with liquid or small metal •For normal ventilation during use, remove the rear of objects on top of this unit. Liquid or metal objects the rack or open a ventilation hole. inside this unit are a fire and electrical shock hazard. •If the airflow is not adequate, the unit will heat up •Do not allow water to enter this unit or allow the unit inside and may cause a fire. to become wet. Fire or elect
ملخص المحتوى في الصفحة رقم 4
Thank you for choosing the DIO8 digital IO box, specifically designed for the Yamaha PM1D digital audio mixing system. The DIO8 outputs and inputs digital signals (such as ADAT, TASCAM, and AES/EBU) as well as analog signals to and from the DSP1D/DSP1D-EX engine controlled via the CS1D control surface. Up to eight digital I/O cards and analog I/O cards can be installed on each DIO8. Front panel I/O UNIT ID 1 PORT B SELECTOR 5-8 2 1-4 I/O UNIT ID PORT B SELECTOR 5-8 1-4 POWER POWER
ملخص المحتوى في الصفحة رقم 5
If the PORT B SELECTOR is set to 5-8, slots 1-4 are A I/O UNIT ID indicator assigned to PORT A and slots 5-8 are assigned to This indicates the connector number (the number of PORT B for input and output signals. the connector used to control the DIO8) of the engine DSP unit (DSP1D/DSP1D-EX) connected to the DIO8. If the PORT B SELECTOR is set to 1-4, only PORT B If more than one connector is connected, either A or B is available for input and output signals
ملخص المحتوى في الصفحة رقم 6
Using slots 1-4 input signals with two DSP1D/ Caution: DSP1D-EXs simultaneously If you are using the MY8-AT card to handle ADAT 1) Connect the INPUT A connector of the DIO8 to OUT- format signals, synchronization may tend to be PUT slot 1-6 of the first DSP1D/DSP1D-EX. lost easily depending on the device that is con- nected. For the most reliable synchronization, we 2) Connect the INPUT B connector of the DIO8 to the recommend that the word clock for d
ملخص المحتوى في الصفحة رقم 7
[MY8-AD]+[MY4-AD]+ [AP8AD]+[AP8DA] cards used [MY8-TD]+[MY8-AT]+[MY8-AE] cards used [MY4-DA] cards used Total 0 cards Up to a total of 8 cards Total 1 card Up to 6 cards Up to the number of vacant DIO8 slots Total 2 cards Up to 4 cards Up to the number of vacant DIO8 slots Total 3 cards Up to 2 cards Up to the number of vacant DIO8 slots Total 4 card Up to 1 card Up to the number of vacant DIO8 slots Total 5 or more cards cannot be used—— Installing an optional I/O card I
ملخص المحتوى في الصفحة رقم 8
I/Os I/O connectors Level Type INPUT A, B RS422 D-sub, half-pitch, 68-pin connector (female) OUTPUT A, B RS422 D-sub, half-pitch, 68-pin connector (female) COM RS232C D-sub,9-pin connector (male) *1 WORD CLOCK IN TTL/75 Ω (ON/OFF) BNC connector WORD CLOCK OUT (X4) TTL/75 Ω BNC connector *1 On the rear panel Slots Eight slots (slots 1-8) are available on the DIO8 for installing digital I/O cards and analog I/O cards. Slot 1 supports a serial interface card (not released ye
ملخص المحتوى في الصفحة رقم 9
YAMAHA CORPORATION Pro Audio & Digital Musical Instrument Division P.O. Box 3, Hamamatsu, 430-8651, Japan
