ملخص المحتوى في الصفحة رقم 1
™
XR 800F
9 Channel Powered Console
Operating Guide
ملخص المحتوى في الصفحة رقم 2
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
ملخص المحتوى في الصفحة رقم 3
ENGLISH ™ XR 800F Powered Sound Reinforcement Mixing Console ™ Congratulations on your purchase of the XR 800F powered mixer. Peavey has packed features from the popular XR 684 into a professional 9-channel, tabletop package. The newest member of the famous Peavey XR family, the XR 800F, represents years of powered mixer experience combined with the latest in technology and packaging. Here are several features you will find on the XR 800F. Eight low-noise, low-Z mic preamps (Channels 1-8) S
ملخص المحتوى في الصفحة رقم 4
AC POWER SECTION The AC POWER SECTION explains the proper connections/method to supply AC power to your XR 800F. Please pay close attention to the precaution(s) noted below in order to ensure both personal and equipment safety. 2 3 1 1. A/C POWER INLET: This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line voltage is used. (S
ملخص المحتوى في الصفحة رقم 5
CAUTION: When the bridge outputs are being used, no other speakers should be connected to the adjacent parallel speaker outputs. In addition, the minimum load for the XR 800F in bridge mode is 8 ohms. Do not allow the total impedance to drop below 8 ohms or serious damage to the amplifier may occur. MASTER IN/OUT The MASTER IN/OUT section describes the functions related to the input and output patch panel located on the rear of your XR 800F. This section is often overlooked but adds the most ver
ملخص المحتوى في الصفحة رقم 6
MASTER FUNCTIONS The MASTER FUNCTIONS section describes those features that are considered master controls. Essentially, this makes up all of the functions on the right-hand, front panel side of your XR 800F. The areas of detail include; Effects, EQ/FLS and Monitor/Master Level Controls. 12 13 14 15 16 17 12. EFFECTS PEAK LED: Illuminates to indicate -6 dB of headroom before the signals being sent to the effects circuit are clipped. Ideally, you would want this LED to light only occasionally if
ملخص المحتوى في الصفحة رقم 7
18 19 18. FLS (Feedback Locator System): These LEDs illuminate to indicate the frequency band of highest energy. When feedback occurs, this system will automatically indicate the graphics slider to use to lessen or eliminate feedback. (NOTE: These LEDs illuminate with any audio signal, not just during feedback.) If feedback occurs, pull down the slider under the brightest LED. 19. GRAPHIC EQUALIZERS: These nine-band equalizers are fixed on one-octave centers. They are designed for 12 dB of
ملخص المحتوى في الصفحة رقم 8
24. MASTER L/R FADERS: This is the master level control for the L and R signals sent to the Left and Right Output jacks. When in Main/Monitor mode [see System Mode Switch (20)] the Monitor Fader controls the monitor signal present at the Left/Mon Power Amp Output (4). The Left and Right Faders would then control the L/R Mix present at the Right/L+R Power Amp Output (4). The nominal position for this control is the 0 dB position. CHANNEL FUNCTIONS The CHANNEL FUNCTIONS section describes the c
ملخص المحتوى في الصفحة رقم 9
27. GAIN: Varies the input gain to each channel. Proper adjustment of the input gain will maximize the signal to noise ratio giving you the quietest operation. With your Channel Fader (35) set to the “0” 27 position, set this control so that the Clip LED (34) barely lights at the highest peaks in your input signal. 28. HIGH EQ: 28 A shelving type of active tone control that varies the treble frequency levels ±15 dB at 12 kHz. It is designed to remove noise or to add brilliance to the sig
ملخص المحتوى في الصفحة رقم 10
CHANNELS 7 - 8 NOTE: Channels 7 - 8 contain features that differ from the previous channels. Only those features are mentioned below. 38 36. RIGHT INPUT: 1/4" input for line level signals. The Right Input is not adjusted by the Gain (27) control. The signal is then routed to the internal power amp. If the XR 800F is in Left/Right mode then the signal will go to the Right Speaker Output (4). In Mon/Main mode the signal is combined with the Left and placed on the Right/L+R Speaker 39 37
ملخص المحتوى في الصفحة رقم 11
PHANTOM POWER 40. PHANTOM POWER SWITCH: Applies 48 V DC voltage to all input XLR connectors to power microphones that require it. CAUTION! When phantom power is switched on, make sure that any channel you are plugging a mic into is turned down in both the main and monitor mixes. Otherwise, there will be a loud pop in the PA. This is normal. It is best to plug all mics into their respective channels with the phantom power switched off. This reduces noise in the PA and reduces the chances o
ملخص المحتوى في الصفحة رقم 12
12 XR 800F BLOCK DIAGRAM CHANNELS 1-6 EFFECTS OUT +48V PHANTOM Tone Control LO MID HI EFFECTS DEFEAT PAN LEVEL EFX LEVEL LO-Z INPUT DIGTAL EFFECTS Pre Gain EFFECTS TO MAIN LINE INPUT TIME COLOR PEAK EFFECTS LED SELECTOR 20 dB Pad Monitor EFFECTS TO MONITOR TAPE OUT CHANNELS 7-8 Tone Control PAN/BALANCE LO MID HI STEREO LINE INPUT LEFT MAIN OUTPUT L/MONO MODE SELECT LEFT/ L-R LEFT POWER AMP INPUT LEVEL EFX LEVEL 63 125 250 500 1K 2K 4K 8K 16K RIGHT +48 PHANTOM LEFT/ MO
ملخص المحتوى في الصفحة رقم 13
13 XR 800F LEVEL DIAGRAM INPUTS MONITOR OUT +30 LEFT & RIGHT OUT MONITOR OUT +21 dBu MAX +21 dBu MAX. +21 dBu GRAPHIC +20 +21 dBV MAX CHANNEL EQ TAPE OUT +16 dBu EQ +15 dB -10 dBV MAX STEREO +12 dB +10 TO POWER AMPS LINE LINE 2 dBu-0 dBV +2 dBu NOMINAL TAPE 0dBu +5 dBu -10 dBV MON -12 dB +11 dBu -20 L/R FADER -15 dB CHANNEL FADER 10 dB GAIN -20 0 dB GAIN -29 dBu -30 LO-Z MIC -40 -48 dBu -50 -60
ملخص المحتوى في الصفحة رقم 14
XR 800F HOOK-UP DIAGRAM MIDI Sound Module Firebass 700 Out L R Recording Deck Line Out CD Player In L R Out L R ™ PVM 22 ™ ™ SP 2G SP 2G ™ ™ SP 112M SP 112M *Shown with system mode switch depressed 14
ملخص المحتوى في الصفحة رقم 15
XR 800F Specifications: Input Specifications: Function Input Z Input Gains Input Levels Bal/ Connector (ohms) Min** Nominal* Max UnBal. Min Low-Z Mic 2.2 k Max (48 dB) -68 dBu -48 dBu -27 dBu Bal. XLR: Pin 1 Gnd, (150 ohms) Min (10 dB) Pin 2 (+), Pin 3 (-) -30 dBu -10 dBu +11 dBu Line Input 22 k Max -49 dBu -29 dBu -8 dBu Unbal. 1/4" TRS: Tip (+), Channels 1-6 (29 dB) Ring (-), Sleeve Ground Min -11 dBu +10 dBu +31 dBu (-10 dB) Ste
ملخص المحتوى في الصفحة رقم 16
Frequency Response: Mic Input to L - R Output 20 Hz — 20 kHz +0 dB/-1 dB Line Input to L - R Output 20 Hz — 20 kHz +0 dB/-1 dB To Power Amplifier Output 20 Hz — 20 kHz +0 dB/-1 dB Total Harmonic Distortion (THD): < 0.01% 20 Hz — 20 kHz mic input to L/R mon. output at nominal level (20 Hz — 80 kHz BW) < 0.01% 20 Hz — 20 kHz line input to L/R output at output at nominal level (20 Hz — 80 kHz BW) < .005% Typical at 1 kHz Graphic Equalizer: Filter Bandwidth 1 octave Filter Frequencies 63, 125, 250,
ملخص المحتوى في الصفحة رقم 17
POWER SECTION Hum and Noise: ™ (400 SC Module with DDT ) -100 dB below 210 watts Power and Load: Damping Factor: 210 W RMS per channel into 4 ohms Greater than 100 @ 1 kHz, 4 ohms 150 W RMS per channel into 8 ohms 420 W RMS Bridge into 8 ohms Input Impedance: 2 k ohms Frequency Response: 20 Hz—20 kHz +0 dB/-1 dB Power Requirements: Dom.: 120 V AC 60 Hz 360 W Nom. Total Harmonic Distortion: Exp.: 220-230 V AC 50/60 Hz 360 W Nom. <0.02% at rated output @ 1 kHz Dimensions (H x W x D): ™ 7.75" x 17.
ملخص المحتوى في الصفحة رقم 18
FRANÇAIS ™ MIXEUR AMPLIFIE R 800F ™ Nous vous félicitons pour l’achat de cette table amplifiée XR 800F. Ce nouveau mixeur amplifié constitue une version 9 canaux en un format table de la XR 684. Nous avons regroupé en un même appareil un nombre impressionnant de fonctionnalités, chacune utilisant les technologies les plus récentes. Voici certaines d’entre elles: Huit entrées micro Jack haute impédance (Canaux 1-8) Six entrées ligne Jack (Canaux 1-6) trois entrées ligne stéréos (Canaux 7-9
ملخص المحتوى في الصفحة رقم 19
ALIMENTATION 1. CONNECTEUR D’ALIMENTATION: Prise pour cordon d’alimentation IEC, fournissant l’électricité à la console de mixage/ampli. Branchez le cordon d’alimentation pour mettre la console sous tension. L’équipement peut être endommagé si une tension d’alimentation incorrecte est utilisée (voir les spécifications de tension sur la console). 2 3 1 2. MARCHE/ARRÊT Interrupteur d’alimentation principal de la table de mixage. La LED d’alimentation (n°21) s’allume lorsque la console est sous t
ملخص المحتوى في الصفحة رقم 20
ENTREES/SORTIES MASTER Cette section se rapporte aux entrées et sorties situées à l’arrière de la XR 800F. C’est là que devront être connectés les divers amplis de puissance, retours amplifiés et modules d’effets que vous utiliserez. Certaines de ces connexions sont expliquées dans le diagramme de branchements de ce manuel. 6. ENTRÉES AMPLI DE PUISSANCE: En se connectant à ces entrées, vous accédez directement aux EQ graphiques et à leur amplificateur de puissance respectif. Tout signal situé en
