ملخص المحتوى في الصفحة رقم 1
Q-MX2 BPM
USER INSTRUCTIONS
ملخص المحتوى في الصفحة رقم 2
Q-MX2 BPM Featuring: Fader “Q” Start Professional products designed for the working DJ. Main Features Separate gain control for each channel Equipped with high quality Crossfader High output to headphones (Replaceable) Soft-touch rubber knobs for better control VCA Fader for Q-Start Control Extremely clean signal to noise ratio Adjustable Crossfader Curve - changes from Light Control Signal Output Jack a normal curve to a quick curve (for crabbing) Talk Over Button
ملخص المحتوى في الصفحة رقم 3
Index Safety Precautions....................................................................................................p.4 Operating Introduction.............................................................................................p.4 Functions (Front Panel).............................................................................................p.5 Inputs & Outputs (Rear Panel)................................................................................p.8 Set-Up....
ملخص المحتوى في الصفحة رقم 4
FRONT PANEL - CONTROLS AND FUNCTIONS 11 14 12 13 15 10 9 16 8 17 7 18 6 19 20 5 21 4 22 3 23 2 1 2 1. FEA THER FADER PLUS™ CROSSFADER - Blends the output signals of any channels assigned to "X" or "Y." When the fader is in the full "X" position, the output signal of any channels assigned to "X" will be controlled by the master volume level. The same fundamentals will apply for "Y." Sliding the fader from one position to another will vary the output signals of the "X" and "Y" channel
ملخص المحتوى في الصفحة رقم 5
FRONT PANEL - CONTROLS AND FUNCTIONS CONT. This is an eff ect used heavily by scratchers and performer DJ's. The mixer simulates this effect when you hold do wn the X and Y fader buttons. The speed of the transform is preset and will only effect any channel assigned to the f ader assign button being depressed. 4. CHANNEL F ADER - These faders are used to control the output signal of any source assigned to its par ticular channel. 5. SPLIT CUE - This button will activate the "S
ملخص المحتوى في الصفحة رقم 6
FRONT PANEL - CONTROLS AND FUNCTIONS CONT. Turn the knob counter-clockwise to decrease a value or clockwise to increase a value. 14. LED LEVEL INDICATORS - The dual LED's indicators along the top of unit are used to detail either the master output level or a combination of the master output level and the cue PFL level. The position of the LED Level Indicator Function Switch (15) will determine the LED Level Indicator's display mode. In the "MASTER" (down) position the meter will det
ملخص المحتوى في الصفحة رقم 7
REAR PANEL - CONTROLS AND FUNCTIONS CONT. 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 22. AC VOLTAGE SELECTOR - Select between 115V/50Hz or 230V/60Hz. Make sure that the selector is set to the proper voltage you are using. 23. BALANCED XLR MAIN OUTPUTS - The Master Output includes a pair XLR Balanced Jacks as well as a pair RCA Unbalanced Jacks (30). The 3-pin XLR jacks send a high current balanced output signal. These jacks should be used when you will be driving an amp or
ملخص المحتوى في الصفحة رقم 8
REAR PANEL - CONTROLS AND FUNCTIONS CONT. 29. AC CONNECTION - This connection is used for your detachable AC power cord. Be sure to only plug your unit in to the recommended power supply. 30. RCA MAIN OUTPUTS - The Master Output includes a pair XLR Balanced Jacks (23) as well as a pair RCA Unbalanced Jac ks. The RCA jacks send a low current unbalanced output signal. These jacks should only be used f or shorter cable runs to signal processors or looping to another mixer. For cable runs
ملخص المحتوى في الصفحة رقم 9
SET-UP INSTRUCTIONS INPUTS/OUTPUTS The MX-1 allows you two types of output connectors Balanced XLR (25) and Unbalanced RCA (32, 33, and 34). Use these connection to connect the output signal from a mixer, cross-over or EQ to your MX-1 mixer. A balanced connection is recommended for cable runs longer that 10ft. When constructing your own XLR cables follow the pin confi guration describe below for proper connections. For cable runs shorter than 10Ft. you may choose the RCA unbalanced output o
ملخص المحتوى في الصفحة رقم 10
SET-UP INSTRUCTIONS Typical Mixer Set-Up CASSETTE DECK TURNTABLE CD PLAYER TURNTABLE This image details a typical DJ Set Up consisting of a microphone, turntables, CD players, and a tape deck. Note: Turntables can only be connected to the Phono Line Level RCA Jacks (36, 38, and 41). Be sure the Line Level Switches (39) are in the "PHONO" position. ©American DJ Supply® - www.americandj.com - Q-MX2 BPM User Instructions page 10
ملخص المحتوى في الصفحة رقم 11
SET-UP INSTRUCTIONS Typical Stereo Set-Up Figure 9 LOUDSPEAKER LOUDSPEAKER Typical Balanced Output Set-up This image details a typical stereo output layout. Note the use of the Balanced XLR Jacks on both the mixer and the amplifi er. Always use the balanced output jacks whenever possible. The balanced output jacks should always be used for cable runs in excess of 10 feet. Using the balanced jacks will ensure a clean signal through out the entire audio system. ©American DJ Supply® - www.ameri
ملخص المحتوى في الصفحة رقم 12
OPERATING INSTRUCTIONS Operating Determinations When installing this mixer, please make sure that the device is not exposed to extreme heat, moisture or dust! There should not be any cables lying around. Doing so endangers you as well as others. Do not operate the mixer in extremely hot (more than 30° / 100°F) or extremely cold (less than 5°C / 40°F) surroundings. Keep away from direct sunlight and heaters. Operate the mixer only after becoming familiar with its functions. Do not permit oper
ملخص المحتوى في الصفحة رقم 13
TECHNICAL SPECIFICATIONS Technical Specifications - Model Q-MX2 BPM Model: Q-MX2 BPM, 3 Channel Mixer Power supply: AC 115/230V, 50/60Hz switchable Dimensions: 11" W x 12.25" D x 3" H Weight: 8 lbs. / 3.5 kg Crossfader: Optical detecting fader start control - Low grounding impedance crossfader Power Consumption: 5W typical, 7W w/ full headphone output Headphone impedance: 16 Ohms Input Sensitivity (Level/Impedence): Line: -14 dBV (200mV) / 12K Ohm +/- 3dB Microphone: -59
