ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
Contents Introduction ....................................................................................................................3 Which configuration is best? ........................................................................... 3 Package Contents ........................................................................................... 4 Factory Defaults ............................................................................................... 4 Do I need a Micro filter? .
ملخص المحتوى في الصفحة رقم 3
Introduction This guide is supplied to help you connect your NB1300 ADSL Modem quickly to your network or Windows computer. If the NB1300 has already been used, we strongly recommend you reset and flush all settings of the unit via the USB cable by pressing and holding the RESET button on the rear of the modem for 10 seconds. Wait for the RDY light to begin pulsing before continuing. Note: Please be aware that connection via USB is only supported in Windows 98SE, Windows Me, Windows 2000 and Wi
ملخص المحتوى في الصفحة رقم 4
Package Contents The following items should be contained in your NB1300 ADSL Modem Package: Quick Start Guide ADSL Modem (NB1300) Power adaptor (12V AC / 1Amp) Telephone line cable (RJ11) Crossover network cable (RJ45) NetComm Communications CD-ROM (CRS767) USB Cable Factory Defaults The following table lists the Factory Defaults of your NB1300 ADSL Modem: Field Setting Details LAN IP address: 192.168.1.1 LAN Subnet Mask: 255.255.255.0 DHCP Server: Enabled (pool 192.168.1.100 - 192
ملخص المحتوى في الصفحة رقم 5
Do I need a Micro filter? Micro filters are used to prevent common telephone equipment, such as phones, answering machines and fax machines, from interfering with your ADSL service. If your ADSL enabled phone line is being used with any other equipment other than your ADSL Modem then you will need to use one Micro filter for each phone device. Splitters may be installed when your ADSL line is installed or when your current phone line is upgraded to ADSL. If your telephone line is already split
ملخص المحتوى في الصفحة رقم 6
Ethernet Gateway Configuration Before continuing, ensure you have the following items and information ready: A Windows 98, ME, NT, 2000 or XP client machine with a Network Interface Card installed. Either a Network Hub and two UTP cables OR one Crossover UTP cable. A telephone line with ADSL service enabled. User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL account (ask your ISP if unsure) . Note: The following procedure presumes your NB1300 is set to a f
ملخص المحتوى في الصفحة رقم 7
Step 2: Configuring the NB1300 1. After connecting all the ADSL Router cables, powering on the ADSL Router, and launching a web browser, such as Internet Explorer or Netscape Navigator, browse to the address http://192.168.1.1. 2. Enter the correct user name and password to access the Configuration tool. The default user name and password are as below. User Name : admin Password : password Note: You must click the Submit button on every page that you make changes on and when you have made all y
ملخص المحتوى في الصفحة رقم 8
Field Setting Details Service name: Any name to describe your ISP User Name: Your ISP will provide a case sensitive User Name in a format similar to your email address. Contact your ISP for details Password: Enter your Password as supplied by your Service Provider (characters are usually all lower case) Disconnect timeout: 0 ❖ Mode/Wan Connection Type: PPPoE LLC or PPPoA VPI: 8 ❖ VCI: 35 ❖ Static IP Address: 192.168.241.101 ❖ Subnet Mask: 255.255.255.0 ❖ Default Gateway: 0.0.0.0 ❖ Bridge mode:
ملخص المحتوى في الصفحة رقم 9
Step 3: Configuring your Computer to use the NB1300 To use the NB1300 ADSL Modem to access the Internet, your computer must have an IP Address that is in the same LAN subnet as the NB1300 ADSL Router and use the NB1300 ADSL Router’s IP address as its gateway. Most applications call for the Primary and Secondary DNS server entries to be made on each computer. These can be automatically assigned by another DHCP server or by enabling the DHCP server on the NB1300 ADSL Modem, and entering the DNS v
ملخص المحتوى في الصفحة رقم 10
Ethernet Modem (Bridge) Configuration Before continuing, ensure you have the following items and information ready: A computer with a Network Interface Card installed or a router (such as the NetComm NB3100). A Crossover UTP cable. A telephone line with ADSL service enabled. User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL account (ask your ISP if unsure). These are not needed for the NB1300, but are required for the computer or router that it will be c
ملخص المحتوى في الصفحة رقم 11
Step 2: Configuring the NB1300 1. After connecting all the ADSL Router cables, powering on the ADSL Router, and launching a web browser, such as Internet Explorer or Netscape Navigator, browse to the address http://192.168.1.1. 2. Enter the correct user name and password to access the Configuration tool. The default user name and password are as below. User Name : admin Password : password Note: You must click the Submit button on every page that you make changes on and when you have made all y
ملخص المحتوى في الصفحة رقم 12
Field Setting Details Service name: Blank ❖ User Name: Blank ❖ Password: Blank ❖ Disconnect timeout: 0 ❖ Mode/Wan Connection Type: 1483 Bridged IP LLC VPI: 8 ❖ VCI: 35 ❖ Static IP Address: 192.168.241.101 ❖ Subnet Mask: 255.255.255.0 ❖ Default Gateway: 0.0.0.0 ❖ Bridge mode: Enabled ❖ Default Setting. Although in most cases you will not be required to alter these default settings for your NB1300, your ISP may identify specific settings to enable connection to their service. Please refer to yo
ملخص المحتوى في الصفحة رقم 13
USB Gateway (Router) Configuration Before continuing, ensure you have the following items and information ready: A Windows 98SE, ME, 2000 or XP client machine. A telephone line with ADSL service enabled. User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL account (ask your ISP if unsure). Note: Please be aware that connection via USB is only supported in Windows 98SE, Windows Me, Windows 2000 and Windows XP. For Windows 95, NT, Linux and Macintosh you should
ملخص المحتوى في الصفحة رقم 14
Step 2: Configuring the NB1300 1. After connecting all the ADSL Router cables, powering on the ADSL Router, and launching a web browser, such as Internet Explorer or Netscape Navigator, browse to the address http://192.168.1.1. 2. Enter the correct user name and password to access the Configuration tool. The default user name and password are as below. User Name : admin Password : password Note: You must click the Submit button on every page that you make changes on and when you have made all y
ملخص المحتوى في الصفحة رقم 15
Field Setting Details Service name: Any name to describe your ISP. User Name: Your ISP will provide a case sensitive User Name in a format similar to your email address. Contact your ISP for details. Password: Enter your Password as supplied by your Service Provider (characters are usually all lower case). Disconnect timeout: 0 ❖ Mode/Wan Connection Type: PPPoE LLC or PPPoA VPI: 8 ❖ VCI: 35 ❖ Static IP Address: 192.168.241.101❖ Subnet Mask: 255.255.255.0❖ Default Gateway: 0.0.0.0 ❖ Bridge mode:
ملخص المحتوى في الصفحة رقم 16
Trouble Shooting Resetting the NB1300 ADSL Modem When the Ethernet cable cannot be used due to an unknown or inaccessible IP address, you will need to reset the NB1300 ADSL Modem to its factory defaults. To reset the ADSL Modem to its factory defaults, use a ballpoint pen to press and hold the RESET button for 10 seconds. Wait 30 seconds for the NB1300 ADSL Modem to reboot. The NB1300 ADSL Modem will now have the default settings, including its default IP address of 192.168.1.1 and default pas
ملخص المحتوى في الصفحة رقم 17
Warranty Registration Form Date of Purchase ….......…………...........………................................. Name ….......…………...........………................................. Company ….......…………...........………................................. Address ….......…………...........………................................. …………………….........……........... Post Code .....………....………. Tel No ( ) ..............……….…. Fax No ( ) ....………...………. E-mail ….......…………...........………...................
ملخص المحتوى في الصفحة رقم 18
ملخص المحتوى في الصفحة رقم 19
Product Warranty The warranty is granted on the following conditions: 1. This warranty extends to the original purchaser (you) and is not transferable; 2. This warranty shall not apply to software programs, batteries, power supplies, cables or other accessories supplied in or with the product; 3. The customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable requirements of NetComm including producing such evidence of purchase as NetComm may require;
ملخص المحتوى في الصفحة رقم 20
