Hobart ML-104858 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

I
N
S
T
R
U
C
T
I
O
N
S
A200 MIXER
MODEL
A200 ML-104859 (without Timer)
ML-104858 (with Timer)
ML-104863 (Deluxe Finish with Timer)
ML-104861 (Floor Model with Timer)
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobartcorp.com FORM 34387 (Feb. 2000)

ملخص المحتوى في الصفحة رقم 2

MODEL A200 MIXER – 2 –

ملخص المحتوى في الصفحة رقم 3

Installation, Operation, and Care of A200 MIXER SAVE THESE INSTRUCTIONS GENERAL 1 The model A200 mixer is a 20 quart, bench-type mixer with a /2 H.P. motor, and a #12 attachment hub. With the use of special agitators, a 12 quart bowl may be used on the A200 mixers. The floor model and the deluxe finish model are equipped with a timer. Most A200 mixers are equipped with a 0 - 15 minute timer. There are a variety of attachments and accessories available for all models, and these are explained in a

ملخص المحتوى في الصفحة رقم 4

OPERATION WARNING: MOVING BEATER IN BOWL. KEEP HANDS, CLOTHING, AND UTENSILS OUT WHILE IN OPERATION, DO NOT USE WITHOUT INTERLOCKED GUARD. CONTROLS All models are furnished with an On-Off toggle switch which controls power to the mixer. The Bowl Guard must be in position or the mixer will not operate. Refer to page 6. If the Bowl Support is not all the way up, the mixer will not operate unless the On-Off switch is held in the up position. The TIMER (if equipped) is used in conjunction with the

ملخص المحتوى في الصفحة رقم 5

A200 A200 WITH TIMER 5 6 4 7 3 ON 8 ON 2 9 1 10 OFF 11 OFF 12 13 14 15 BOWL LIFT ATTACHMENT HUB CONTROL HANDLE THUMB SCREW PANEL SPLASH GEAR SHIFT GUARD LEVER APRON WIRE CAGE BOWL SUPPORT AGITATOR BOWL BOWL LIFT CLAMP SLIDEWAYS ALIGNMENT PIN PL-53477 Fig. 1 To Raise the Bowl While Mixing To raise the bowl while the agitator is mixing the product (when required by recipe or when using the Bowl Scraper Attachment): Load ingredients. Close Wire Cage Assembly. Select Low speed. To begin mixing, h

ملخص المحتوى في الصفحة رقم 6

Bowl Guard (Fig. 2) The Wire Cage Assembly on the Bowl Guard can be rotated out-of-the-way to add ingredients or access the bowl and agitator. To rotate the Wire Cage Assembly to the rear . . . Rotate the Wire Cage Assembly to the left until it is positioned underneath the Splash Guard. Note how the grooves on the nylon Retainers allow the Wire Cage to ride around the circular Ridge of the planetary Drip Cup. The Wire Cage must be returned to the front and center position for the mixer to opera

ملخص المحتوى في الصفحة رقم 7

CLEANING WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING PROCEDURE. The mixer should be thoroughly cleaned daily. Bowls and agitators should be removed from the mixer and cleaned in a sink. DO NOT use a hose to clean the mixer — it should be washed with a clean damp cloth. The apron (Fig. 1) may be removed by loosening the thumb screws. The Drip Cup-Splash Guard (which is secured by three screws) should be removed periodically and wiped clean. For cleaning the Bowl Guard (incl

ملخص المحتوى في الصفحة رقم 8

SERVICE If service is needed on this equipment, contact your local Hobart Service Office. FORM 34387 (Feb. 2000) – 8 – PRINTED IN U.S.A.