ملخص المحتوى في الصفحة رقم 1
30” Built-In Wall Oven
Installation
with Microwave
Instructions JTP86, JT965
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
• Proper installation is the responsibility
Before You Begin
of the installer and product failure due
Read these instructions carefully and completely. to improper installation is NOT covered
under warranty.
• IMPORTANT—Save these
• NOTE—This appliance must be properly
instructions for local inspector’s use.
grounded.
• IMPORTANT—Observe all
• AT
ملخص المحتوى في الصفحة رقم 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety Electrical • Be sure your oven is installed properly by Requirements a qualified installer or service technician. We recommend you have the electrical wiring • Be sure the oven is securely installed in a and hookup of your oven connected by a cabinet that is firmly attached to the house qualified electrician. After installation, have the structure. Weight on the oven door could electrician show you where your main oven cause
ملخص المحتوى في الصفحة رقم 3
EASY INSTALLATION OF YOUR NEW 30" WALL OVEN IM IM IM IM IM IM IM IM IM IM IM IM B B B B B B B B B B B Be e e e e e e e e e e eP P P P P P P P P P P P fo fo fo fo fo fo fo fo fo fo fo fo O O O O O O O O O O O O r r r r r r r r r r r rR R R R R R R R R R R R e e e e e e e e e e e e T T T T T T T T T T T T y y y y y y y y y y y yA A A A A A A A A A A A o o o o o o o o o o o ou u u u u u u u u u u u N N N N N N N N N N N N T T T T T T T T T T T T b b b b b b b b b b b b- - - -
ملخص المحتوى في الصفحة رقم 4
Installation Instructions Pre-Installation Checklist cont. Place the oven on a table or platform Remove the bottom trim from the top even with the cutout opening. of the oven. It will be installed at the (Platform must support 255 lbs.) end of the installation process. The trim is wrapped separately and taped to the top of the unit. 4
ملخص المحتوى في الصفحة رقم 5
Installation Instructions A Cutout for Built-In Oven with Microwave Cabinet *CABINET Cabinet Width 30” W WIDTH idth 30" 20” 20" 30” Recommended Minimum Cutout W CUTOUTidth Junction Box Cutout Location JUNCTION BOX WIDTH 28 1/2” Min. Location LOCATION Allow 11/16” for 28 1/2" MIN. from Floor 21 5/8” 28 5/8” Max. 28 5/8" MAX. overlap of oven ALLOW 11/16" over side edges FOR OVERLAP OF OVEN OVER of cutout Cutout Depth 23 1/2” Min. SIDE EDGES OF CUTOUT. Cutout Width 28 1/2” Min. Opening 28 5/8” Max.
ملخص المحتوى في الصفحة رقم 6
Installation Instructions B Electrical Connections Turn off the circuit breaker or remove ATTENTION INSTALLER B1 fuses to the oven branch circuit. All electric wall ovens must be hard wired With the oven supported on a table or B2 (direct wired) into an approved junction platform in front of the cabinet opening, box. A plug and receptacle is NOT permitted connect the flexible conduit to the on these products. electrical junction box as shown below. Position the conduit in such a manner DO NOT sh
ملخص المحتوى في الصفحة رقم 7
Installation Instructions B Electrical Connections cont. New Construction and Three-Conductor Branch B3 B4 Four-Conductor Branch Circuit Connection Circuit Connection When connecting to a three-conductor branch circuit, if local codes permit: • When installing in new construction, or a. Connect the bare oven ground conductor • When installing in a mobile home, or with the crimped neutral (white) lead to • When installing in a recreational vehicle, or the branch circuit neutral (white or gray in
ملخص المحتوى في الصفحة رقم 8
Installation Instructions C Securing the Oven in the Opening Sliding the Oven Into the Drilling the Pilot Holes and C1 C2 Opening Mounting the Oven a. Loop (do not tie) a 36” string around the conduit before the oven is slid into place. NOTE: Before drilling the pilot holes, This will keep the conduit from falling make sure the oven is pushed as far behind the oven. back into the opening as it will go and centered. a. Drill through the mounting holes (top and bottom) of the side trim, for the #8
ملخص المحتوى في الصفحة رقم 9
Installation Instructions To install a single metal bottom trim assembly (on some models), use sections C3 and C4. To install a metal bottom trim with a plastic bottom trim (on some models), use sections C3–C5. Preparing for the Bottom Installing the Plastic Bottom C3 C5 Trim Installation Trim (on some models) a. With oven installed, take the bottom trim a. Make sure flat side is up on the plastic and center it on the bottom front edge of bottom trim. the cabinet opening. b. Find the key slot on
ملخص المحتوى في الصفحة رقم 10
Installation Instructions D Replacing the Oven Door Open the oven door as far as it D3 NOTE: The oven door is heavy. You will open. may need help lifting the door high enough to slide it into the hinge slots. Push the hinge locks up against the D4 Do not lift the door by the handle. front frame of the oven cavity, to the locked position. Hinge in Lift the oven door by Locked Position D1 placing one hand on each side. The door is heavy, so you may need help. Do not lift the door Notch of Hinge by
ملخص المحتوى في الصفحة رقم 11
Installation Instructions Pre-Test Checklist Remove all protective film, if present, Check that the bottom trim is installed and any stickers. properly (see page 9). Check to be sure that all wiring is Check to be sure the mounting screws secure and not pinched or in contact are installed and flush with the side trim with moving parts. (see page 8). Operation Checklist Remove all items from the inside NOTE TO ELECTRICIAN: The power of the oven. leads supplied with this appliance are UL recognize
ملخص المحتوى في الصفحة رقم 12
NOTES 12
