Dacor MMD30B دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installat Ion Instruct Ions
MIcrowave In -a -Drawer ™
For use with models:
MMDV30S
MMD30S
MMD30B
Part No. 101589 Rev. C TINSEB448MRR1

ملخص المحتوى في الصفحة رقم 2

ملخص المحتوى في الصفحة رقم 3

t able of c ontents Appliance Safety ..........................................................................1 Clearances and Dimensions .......................................................3 Installation Recommendations ...................................................1 Anti-Tip Block ..............................................................................4 Important Notes To The Installer ................................................1 Installation Instructions .................

ملخص المحتوى في الصفحة رقم 4

IMantport s afety InstructIons WARNINGS If the information in this manual is not followed exactly, a fire or electrical shock may result that could cause property damage, personal injury or death. To reduce the risk of tipping, the Microwave In-A-Drawer™ must be secured by a properly installed Anti-Tip block. • This drawer must be electrically grounded in accordance with local codes. • Make sure the wall coverings and the cabinets around the drawer can withstand the heat generated by the mic

ملخص المحتوى في الصفحة رقم 5

A. 6" A B B. Electrical outlet location C C. Anti-Tip block E D D. 5" E. 3 1/2" F F. 4" G G. 28 7/16" opening H K I K. Allow 1/4" overlap Q N H. 14 3/4" to bottom of Anti-Tip block J I I. Allow 3/4" overlap L J. 23 1/2" minimum depth M Q. 15 3/16" ± 1/16" opening L. 36" countertop height A M. Allow 7/16" overlap N. Floor must support 100 lbs. O. 19" to top of floor O B P. *30" cabinet minimum P NOTE:OpenTop Cabinet illustrated Figure 1 D C E F G I H J K L M DesIgn s pecIIf tIca ons O M N DRAWER

ملخص المحتوى في الصفحة رقم 6

DIes gn s Ipec If tIca ons ANTI-TIP BLOCK Normal Installation Steps Anti-Tip BLOCK Installation Instructions To reduce the risk of tipping of the drawer, the Anti-Tip A. 6" A block must be properly installed located 14 3/4" above the B B. Electrical outlet location C floor on which the Microwave In-A-Drawer™ will sit. The C. Anti-Tip block 6" Anti-Tip block must be provided by the installer. See E D D. 5" Figures 2, 3 and 4. The Anti-Tip block prevents serious E. 3 1/2" F F. 4" injury that

ملخص المحتوى في الصفحة رقم 7

ItIallanston IInstruct ons VERIFYING PACKAGE CONTENTS DRAWER INSTALLATION • Remove all packing materials from inside the drawer. DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the top of the Microwave In-A-Drawer™. • Remove the feature sticker, if there is one. Check the drawer for any damage, such as misaligned or bent drawer, damaged drawer seals and sealing surfaces, broken or loose drawer guides and dents inside the cavity or on the front side of the drawer. If there is any

ملخص المحتوى في الصفحة رقم 8

Specifications contained within are subject to change without notice. ® No liability is assumed by DACOR for changes in specifications. The information and images in this book are the copyright property of Distinctive Appliances, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Distinctive Appliances, Inc. Web Site: www.Dacor.com Phone: (800) 793-0093 © 2006 Distinctive Appliances, Inc. a