ملخص المحتوى في الصفحة رقم 1
Nady wireless systems are type accepted under FCC rules
parts 90, 74, and 15.
This device complies with RSS-210 of Industry & Science
Canada.
Operation is subject to the following two conditions: (1) this
NADY XR-61
device may not cause harmful interference and (2) this device
must accept any interference received, including interference
VHF DigiTRU Diversity™ System
that may cause undesired operation.
XR PRO SERIES
WIRELESS MICROPHONE SYSTEM
OWNER’S MANUAL
NADY SYSTEMS, INC. • 6701 SHELLMOUND
ملخص المحتوى في الصفحة رقم 2
CONTENTS CONTENTS ........................................................................................2 INTRODUCTION ................................................................................3 SYSTEM FEATURES..............................................................................4 OPERATION ......................................................................................5 XR-61 RECEIVER ..............................................................................5 WHT-15 HA
ملخص المحتوى في الصفحة رقم 3
INTRODUCTION XR-61 RECEIVER Reception Mode DigiTRU Diversity™ Thank you for purchasing a Nady XR Pro Series XR-61 Diversity Wireless Microphone Controls Power ON/OFF, volume control, mute control System and congratulations on your choice. Also available is the XR-62, which is a single rackmount unit with dual receivers for operation of 2 channels simultaneously. The XR Pro Connectors Balanced XLR and unbalanced adjustable Series systems are loaded with top professional operating features and
ملخص المحتوى في الصفحة رقم 4
SYSTEM FEATURES SPECIFICATIONS • Available on selected frequencies in the VHF high band XR PRO SERIES OVERALL SYSTEM PERFORMANCE (171-216 MHz) for interference-free, long-range performance Frequency Response 25-20,000 Hz, +/-3dB • Proprietary companding circuitry for an industry-best 120dB Dynamic Range 120dB Dynamic Range, and the clearest, most natural sound available Total Harmonic Distortion <0.3% • Operating Range: Up to 250 feet typical (depending on site conditions)-up RF Carrier Frequen
ملخص المحتوى في الصفحة رقم 5
OPERATION XR-61 RECEIVER 38 1. Rackmounting the Receiver The XR-61 receiver is supplied with RACK EARS (1) which can be attached with the screws provided on the front of the side panels to enable rackmounting the receiver. (Note: Do not mount the receiver in a rack directly above an amplifier or other source of high heat-this could degrade the performance of the XR-61/62. Always ensure adequate airflow and heat dissipation in any rack configuration.) 44 2. Powering the Receiver 43 Plug the 12V
ملخص المحتوى في الصفحة رقم 6
4. Microphone Operation 5. Connecting the Audio Output a. Turn on The Link 2 by sliding the ON/STANDBY/OFF SWITCH (41) to the STANDBY The XR-61 receiver provides both a fixed mic level BALANCED AUDIO OUTPUT XLR (10) position (transmitter on, audio muted) or the ON position (transmitter and audio both on). and an adjustable line level UNBALANCED AUDIO OUTPUT 1/4” JACK (11). The level The LOW BATTERY INDICATOR LED (40) will give a single quick flash, indicating usable from the UNBALANCED OUTPUT is
ملخص المحتوى في الصفحة رقم 7
THE LINK 2™ PLUG-IN TRANSMITTER 1. Transmitter Set-Up First, slide open the BATTERY COMPARTMENT DOOR (43) to expose compartment. Insert a fresh 9V ALKALINE BATTERY (45), observing polarity. Close the battery compartment door. 2. Handheld Microphone Installatio • Step 1 - Rotate the transmitter’s threaded LOCKING RING (37) clockwise toward the XLR CONNECTOR (36) until it stops. XR-61 Receiver 1 • Step 2 - Hold your mic in one hand and The Link 2 in the other. • Step 3 - Plug your mic into the XL
ملخص المحتوى في الصفحة رقم 8
WHT-15 HANDHELD MICROPHONE TRANSMITTER 1. Unscrew the BATTERY COMPARTMENT COVER (17) and remove, exposing the BATTERY HOLDER (18). Insert a fresh 9V ALKALINE BATTERY (19), observing the correct polarity as marked, and screw the cover back on to the microphone. Make sure the cover is screwed 35 32 on completely. A fresh alkaline battery can last up to 16 hours in use, but in order to ensure optimum performance, it is recommended that you replace the battery after every 10 hours of use. 34 33 2.
ملخص المحتوى في الصفحة رقم 9
WGT-15 INSTRUMENT BODYPACK TRANSMITTER 1. Snap open the BATTERY COMPARTMENT (30) and insert a fresh 9V BATTERY (31), observing the correct polarity. Close the compartment. The WGT-15 is provided with a 3.5 mm LOCKING JACK (32) for connecting the INSTRUMENT CABLE (35). To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To unplug, reverse the process. Slip the transmitter into a pocket or clip on to your clothes or instrument strap. (Note: As
ملخص المحتوى في الصفحة رقم 10
WLT-15 LAVALIER/LAPEL OR HEADWORN MICROPHONE BODYPACK TRANSMITTER 24 1. Snap open the BATTERY COMPARTMENT (22) and insert a fresh 9V BATTERY (23), observing the correct polarity. Close the compartment. 2. The WLT-15 is provided with a 3.5 mm LOCKING JACK (24) for connecting the micro- 29 phone. Plug in either the LAVALIER/LAPEL (25) or the HEADWORN MICROPHONE (26), as 28 supplied. To secure the connection, turn the metal slip ring on the plug clockwise to thread it on to the jack. To unplug,
