ملخص المحتوى في الصفحة رقم 1
INSTRUCTION MANUAL
HF/VHF/UHF
ALL MODE TRANSCEIVER
i7000
ملخص المحتوى في الصفحة رقم 2
e r IMPORTANT EXPLICIT DEFINITIONS READ THIS INSTRUCTION MANUAL WORD DEFINITION CAREFULLY before attempting to operate the Personal injury, fire hazard or electric transceiver. RWARNING shock may occur. CAUTION Equipment damage may occur. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating in- If disregarded, inconvenience only. No structions for the IC-7000. risk or personal injury, fire or electric NOTE shock. FOREWORD SUPPLIED ACCESSORIES We understand that you ha
ملخص المحتوى في الصفحة رقم 3
ILLUSTRATIONS Front panel !6 @4 @3 @2 @1 @0 !9 !8 !7 q w e !5 t yu i o !0 !1 !2 !4 !3 r HM-151 ⁄3 SPCH TUNER ⁄2 XFC /LOCK /CALL z ⁄1 MW x V/M ⁄0 F-2 c . F-1 , v Mic element 1.8 3.5 7 MODE 12 3 m 10 14 18 FIL 45 6 n b 21 24 28 GENE 78 9 50 144 430 F-INP . 0 CE ENT The front panel and HM-151’s panel descriptions are descrived between pages 1 to 4, and on page 9, respec- tively (see the Chapter 1 (Panel de- scription) for more details). i-2
ملخص المحتوى في الصفحة رقم 4
■Front panel ■Microphone (HM-151) qAF GAIN CONTROL [AF] (inner control; p. 33) zSPCH/LOCK KEY [SPCH/LOCK] (p. 34, 37) wRF GAIN CONTROL/SQUELCH CONTROL xPTT SWITCH [PTT] (p. 37) [RF/SQL] (outer control; p. 35) cUP/DOWN SWITCHES [Y]/[Z] ePOWER KEY [PWR] (p. 25) vTRANSMIT INDICATOR rFRONT PANEL LATCH (p. 16) bKEYPAD (pgs. 28, 29) tPASSBAND TUNING/M-ch/RIT CONTROLS nFILTER SELECTION [FIL] (p. 77) [PBT/M-ch/RIT] (pgs. 75, 79, 88, 102, 106) mMODE KEY [MODE] (p. 34) yTWIN PBT (M-ch/RIT) INDICATOR (pgs
ملخص المحتوى في الصفحة رقم 5
PRECAUTIONS AVOID placing the transceiver against walls or putting RWARNING RF EXPOSURE! This device emits anything on top of the transceiver. This will obstruct heat Radio Frequency (RF) energy. Extreme caution should be dissipation. observed when operating this device. If you have any questions regarding RF exposure and safety standards Place unit in a secure place to avoid inadvertent use by please refer to the Federal Communications Commission children. Office of Engineering and Technology’s
ملخص المحتوى في الصفحة رقم 6
TABLE OF CONTENTS IMPORTANT …………………………………………i-1 DDifferences between VFO and FOREWORD ………………………………………… i-1 memory mode ………………………………… 26 EXPLICIT DEFINITIONS …………………………… i-1 ■VFO operation …………………………………… 27 SUPPLIED ACCESSORIES …………………………i-1 DSelecting VFO A/VFO B ……………………… 27 ILLUSTRATIONS ……………………………………i-2 DVFO equalization……………………………… 27 ■Front panel ……………………………………… i-3 ■Selecting VFO/memory mode ………………… 27 ■Microphone (HM-151) ………………………… i-3 ■Selecting an operating band …………………… 28 PRECAUTIO
ملخص المحتوى في الصفحة رقم 7
TABLE OF CONTENTS 4 Paddle Polarity ……………………………… 50 DIF filter shape (SSB/CW only) ……………… 78 1 5 Keyer Type ………………………………… 50 ■Twin PBT operation …………………………… 79 6 MIC U/D Keyer (HM-103) ………………… 50 ■Noise blanker …………………………………… 80 DPaddle operation 2 DNoise blanker set mode ……………………… 80 from [MIC] connector ………………………… 50 1 NB Level …………………………………… 80 ■Operating RTTY (FSK) ………………………… 51 2 NB Width …………………………………… 80 3 DConvenient functions for receive …………… 52 ■Noise reduction ………………………………… 81 DRTTY r
ملخص المحتوى في الصفحة رقم 8
TABLE OF CONTENTS ■Set mode description ………………………… 122 8 MEMORY OPERATION ………………102–112 ■Quick set mode ………………………………… 123 ■Memory channels ……………………………… 102 ➥ RF Power (all modes) ……………………… 123 ■Memory channel selection …………………… 102 ➥ MIC Gain (SSB/AM/FM modes)…………… 123 ■Memory programming ………………………… 103 ➥ SSB TBW (WIDE) L (SSB mode) ………… 123 DProgramming in VFO mode………………… 103 ➥ SSB TBW (WIDE) H (SSB mode) ………… 124 DProgramming in memory mode …………… 104 ➥ SSB TBW (MID) L (SSB mode) …………… 124 ■Mem
ملخص المحتوى في الصفحة رقم 9
TABLE OF CONTENTS 16 Auto Repeater ……………………………… 132 DCodes for memory name contents ………… 149 1 17 Tuner (Auto Start) ………………………… 132 DSplit/Duplex frequency setting……………… 149 18 Tuner (PTT start) …………………………… 133 DRepeater tone/tone squelch frequency 19 [TUNER] Switch …………………………… 133 2 setting ………………………………………… 149 20 VSEND Select ……………………………… 133 DDTCS code and polarity setting …………… 149 21 SPEECH level ……………………………… 133 3 18 SPECIFICATIONS …………………………150 22 SPEECH Language ……………………… 133 ■General …
ملخص المحتوى في الصفحة رقم 10
1 PANEL DESCRIPTION ■Front panel See the illustration of the Front panel on page i-2. qAF GAIN CONTROL [AF(SET)] (inner control; p. 33) •When functioning as squelch control (RF gain is fixed at maximum.) ➥Rotate to vary the audio output level from the speaker or headphones. Noise squelch (FM/WFM modes) Noise squelch threshold Audio output S-meter squelch (FM/WFM modes) increases threshold S-meter Squelch is Audio outut squelch open. decreases Push momentarily to enter the set mode menu. Lowest
ملخص المحتوى في الصفحة رقم 11
PANEL DESCRIPTION 1 yTWIN PBT (M-ch/RIT) INDICATOR ✔ What is the PBT control? 1 (pgs. 75, 79, 88, 102) PBT electronically narrows the IF passband width to reject interference. This transceiver uses DSP to implement PBT. ➥Indicates the status of [PBT/M-ch/RIT] (t) acti- vates as the Twin PBT function or memory chan- ➥While M-ch/RIT is selected: nel/RIT control. ●● Rotate the inner control to select a memory •Indicator is green when the Twin PBT is selected. channel number (p. 102). •Indicator is
ملخص المحتوى في الصفحة رقم 12
1 PANEL DESCRIPTION !0MANUAL NOTCH KEY [MNF/ADJ] (p. 83) !5MAIN DIAL TENSION LATCH ➥Push momentarily to turn the manual notch func- Selects the main dial drag. tion ON and OFF in SSB, CW and AM modes. •Three positions are available. Upper setting turns on •“ ” appears on the display when the function is ac- clicks as the dial is turned.. tivated. !6HEADPHONE JACK [PHONES] (p. 18) ➥Push and hold for 1 sec. to enter the manual Accepts headphones with 8–16 impedance. notch filter set mode. ✔ What i
ملخص المحتوى في الصفحة رقم 13
PANEL DESCRIPTION 1 !9TUNING STEP KEY [TS] (pgs. 30–32) @2FUNCTION DISPLAY 1 ➥While in SSB/CW/RTTY modes, push momentar- Shows the operating frequency, function key menus, ily to turn the programmable tuning step ON and simple band scope display, selected memory chan- OFF. While in AM/FM/WFM modes, push mo- nel, receiving TV channel, etc. See p. 13 for details. mentarily to toggle the programmable tuning step @3 PRE AMP/ATTENUATOR KEY [P.AMP/ATT] and 1 MHz quick tuning step. (p. 74) •While the p
ملخص المحتوى في الصفحة رقم 14
1 PANEL DESCRIPTION DMenu M-2 functions ■Multi-function keys DMenu M-1 functions MEM MW MCL V/M F-1 F-2 F-3 F-4 SPL A/B FIL XFC F-1 F-2 F-3 F-4 MEMORY MENU (p. 105) Push momentarily to indicate the memory SPLIT OPERATION MEM frequency and modes. ➥Push momentarily to toggle the split func- F-1 •Memory list indication is available. SPL tion ON and OFF. (p. 91) F-1 •“” and transmit frequency appear when MEMORY WRITE (pgs. 103, 104) the split function is ON. ➥Push and hold for 1 sec. to turn the qu
ملخص المحتوى في الصفحة رقم 15
PANEL DESCRIPTION 1 DURING FM/WFM OPERATIONS: BREAK-IN FUNCTION (p. 87) 1 ➥Push momentarily to select semi-break-in, BRK VOX DUP TON 9600 full break-in (QSK) and break-in OFF. F-1 F-1 F-2 F-3 F-4 •“ ” or “ ” appears when selecting semi break-in or full break-in, respectively. •An external switch, such as a foot switch, must be connected to the ACC socket (pin 3, VOX FUNCTION (p. 85) pin 7 or RTTY SEND—see p. 23) if break-in ➥Push momentarily to toggle the VOX func- is turned OFF. VOX tion ON and
ملخص المحتوى في الصفحة رقم 16
1 PANEL DESCRIPTION DTMF OPERATION DMenu S-1 functions Push to enter DTMF memory mode. DURING SSB/AM OPERATION: DTM (p. 67) F-4 •The DTMF send menu or DTMF root menu VO MET VSC appears depending on the “DTMF 1st F-1 F-2 F-3 F-4 Menu” setting in the miscellaneous (others) set mode. (p. 136) DURING CW OPERATION: DMenu S-2 functions VO KEY MET VSC F-1 F-2 F-3 F-4 DURING VFO MODE: SCN PRI V/M VSC DURING RTTY OPERATION: F-1 F-2 F-3 F-4 VO DEC MET VSC DURING MEMORY MODE: F-1 F-2 F-3 F-4 SCN SEL V/M VS
ملخص المحتوى في الصفحة رقم 17
PANEL DESCRIPTION 1 DMenu S-3 functions DMenu G-1 (Scope) functions 1 MW MPW MPR SPN HLD FIX SPD F-1 F-2 F-3 F-4 F-1 F-2 F-3 F-4 MEMORY WRITE (pgs. 103, 104) SWEEP STEPS (pgs. 72, 73) Push and hold for 1 sec. to store the dis- ➥Push momentarily to change the sweep SPN MW played VFO frequency and operating step size. F-1 F-1 mode into the selected memory channel. •Available steps are ±10, 25, 50, 100 and 250 kHz. ➥Push and hold for 1 sec. to change the MEMO PAD WRITE (p. 111) sweep steps to ±10 k
ملخص المحتوى في الصفحة رقم 18
1 PANEL DESCRIPTION ■Microphone (HM-151) See the illustration of the HM-151 on page i-2. zSPCH/LOCK KEY [SPCH/LOCK] .PROGRAMMABLE FUNCTION KEYS [F-1]/[F-2] ➥Push momentarily to have the frequency, etc. an- Program and perform a selected function. •The functions can be assigned in the miscellaneous (oth- nounced by the speech synthesizer. (p. 34) ers) set mode (p. 135). The default settings for [F-1] and •The parameters to be announced can be selected in [F-2] are “MPW” and “MPR,” respectively. t
ملخص المحتوى في الصفحة رقم 19
PANEL DESCRIPTION 1 DMicrophone connector 1 MICROPHONE CONNECTOR INFORMATION Rear panel view CAUTION:DO NOT short pin 1 to ground as this can damage the internal 8 V regulator. 87654321 • When HM-151 is connected HM-151 q +8 V DC output PIN NO. FUNCTION DESCRIPTION w Frequency up/down 1 +8 V DC output Max. 10 mA e M8V SW Frequency up Ground 2 r PTT Frequency down Ground through 470 t GND (Microphone ground) 3 HM-151 connection Goes to ground to connect y Microphone input 8 HM-151 data Control
ملخص المحتوى في الصفحة رقم 20
1 PANEL DESCRIPTION ■Rear panel qw e rto y ui MIC KEY ACC DATA GND !0 ANT2 ANT1 DC 13.8V !2 !1 qELECTRONIC KEYER JACK [KEY] (p. 22) u RTTY JACK [RTTY] (p. 23) Accepts a paddle to activate the internal electronic Connects an external terminal unit for RTTY (FSK) keyer. operation. •The keying polarity, mark/shift frequencies and etc. can •Selection between the internal electronic keyer and be selected in quick set mode (p. 125). straight key operation can be made in the keyer set mode. (p. 50) iEX
