ملخص المحتوى في الصفحة رقم 1
2.4GHZ WIRELESS SYSTEM FOR
POLICE VIDEO RECORDING
USER GUIDE
Revision B Page 1 of 9 12/11/08
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS 1. Quick Set Up and Operation .......................................................3 2. Installation....................................................................................4 3. Guidelines For Best Performance ................................................6 4. Troubleshooting Guide.................................................................7 5. Technical Specifications...............................................................8 6. Service and War
ملخص المحتوى في الصفحة رقم 3
QUICK SET UP AND OPERATION Synching Up The Transmitter and Base The synch operation only needs to be performed the first time a system is used, or a new bodypack is used with a base previously synched to another bodypack. Do not perform the synch operation multiple times; it only needs to be done one time when a new bodypack is used with a new base. 1) Turn the transmitter power switch to ON and place the transmitter in the recharge cradle of the base. The transmitter goes in the ba
ملخص المحتوى في الصفحة رقم 4
EMG Panic Button (if wired for use in your vehicle) 1) The EMG or Panic Button can be programmed to do many things but may not be connected in your vehicle. Check with your technical department to understand what this button will control before you use it. 2) In Record mode: Press the EMG button on the transmitter, a beep will sound and the relay will be triggered at the receiver. 3) In Standby mode: Press the EMG button on the transmitter, a beep will sound, the green In-Use indica
ملخص المحتوى في الصفحة رقم 5
2. Plug the 3.5mm stereo plug into the audio input jack of the recording device. Description Position Inside Car Mic Audio Tip Sleeve Transmitter Audio Ring Ring Audio Ground Sleeve Tip 3. If it is to be used, plug in the in-car microphone into the In-Car Mic jack in the side of the receiver base. 4. Turn on the transmitter and place it in the charging cradle with the beltclip facing out. The Charge LED will light if there is power. If the LEDs do not come on, c
ملخص المحتوى في الصفحة رقم 6
4) Guidelines and recommendations for best performance. Compatibility The transmitter and receiver must synchronize to work together (see Synch process on page 3). The synch operation only needs to be performed the first time a system is used, or when a new bodypack is used with a base previously synched to another bodypack. Do not synch multiple times, just once until a new bodypack is used. Any PR24N can be synchronized with any PB24N base. Using Multiple Wireless Systems The PW24
ملخص المحتوى في الصفحة رقم 7
5) Trouble Shooting Guide Problem Possible Causes Solutions No audio and no In-Use LED Receiver is not powered Make sure that the power light on the receiver when supply is properly connected transmitter is on and In-Use Transmitter and receiver not Turn on transmitter and place synchronized in recharge cradle. Press the In-Use button until the In-Use LEDs flash 3 and the pair will be synched No (or low) Audio with all In- Lapel Microphone not connected Check the mic connection a
ملخص المحتوى في الصفحة رقم 8
PR24N RECEIVER BASE STATION Controls Video Trigger Active +12/GND Indicators IN-USE LED: GREEN CHARGE LED: CHARGING -> RED FULL CHARGED -> GREEN Connections In Car Mic 2.5mm Mono Plug Un-terminated Cord RED +12V DC Power BLUE Microphone Trigger (Ground or 12VDC = Transmitter On) BLACK AUX (Panic) Trigger (+12V when EMG is pushed) YELLOW Left Channel (Inside Mic) ORANGE Power Ground BROWN Auto Talk (5V = mic off, 0V =
ملخص المحتوى في الصفحة رقم 9
Factory Service (North America) If factory service is required, ship the unit prepaid in its original carton to: Telex Audio Service c/o Telex Communications 8601 East Cornhusker Highway Lincoln, NE 68507-9702 U.S.A. Tel: 402/467-5321 or 800-553-5992 Fax: 402/467-3279 Enclose a note describing the problem along with any other pertinent information and how to contact you. Warranty (Limited) Telex products are guaranteed against malfunction due to defects in materials or workmanship
