ملخص المحتوى في الصفحة رقم 1
swisherinc.com
OWNER’S
MANUAL
MODEL NO.
RTB115441
RTB134412V
RTB14544
44” ROUGH CUT
TRAIL CUTTER
Assembly
Operation
Service and Adjustment
Repair Parts
Rev. 05-033
1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093
Made In The
PHONE (660) 747-8183 FAX (660) 747-8650
Manufacturing quality lawn care equipment since 1945
USA
10292
ملخص المحتوى في الصفحة رقم 2
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1) Engine Warranty All engines utilized on our products have a separate warran
ملخص المحتوى في الصفحة رقم 3
Thank you for choosing Swisher’s 44 ‘’ Trailcutter. Before operating your cutter, please read, understand and follow all of the safety precautions and other instructions explained in this manual . As with all power equipment, lawn mowers,and cutters can be potentially dangerous if improperly used. SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of pe
ملخص المحتوى في الصفحة رقم 4
• Turn off the blades when not cutting. Before leaving the machine, turn off the blades and stop the engine. • Watch for traffic when operating near or crossing roadways. • Do not operate the cutter if it has been dropped or damaged in any manner or if the mower vibrates excessively. Excessive vibration is an indication of damage. Repair cutter as necessary. • Dress properly. Do not operate the cutter when barefoot or wearing open sandals. Wear only solid shoes with good traction when cut
ملخص المحتوى في الصفحة رقم 5
OPERATING YOUR TRAILCUTTER The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before staring any cutting machine and while operating such a machine. The operation of any cutter produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence o
ملخص المحتوى في الصفحة رقم 6
ENGAGING BLADES Note: Do not attempt to start the unit with the T-handle console in the ‘’ ENGAGED ’’ position. • Engage blades by pulling down the T-handle lever into the horizontal position. • Return lever to the vertical position to disengage blades. See detail on page 14 figure – 8 • The braking system is applied when the blades become disengaged. It is designed to bring the blades to a quick stop ( approximately 7 seconds. ) Each TrailCutter brake system has been tested for safety , the con
ملخص المحتوى في الصفحة رقم 7
CUTTER HEIGHT ADJUSTMENT • There is approximately 4 inches of height adjustment. • Rotate height adjust crank handle in a clockwise direction to lower the mower deck. counter-clockwise direction to lift the mower deck. • Dense areas of material should be cut twice. • Push handle down to lock height position. TOW HITCH OFFSET • When offsetting the cutter do so to the side opposite the discharge of the tow vehicle. • Swisher recommends if the tow vehicle is equipped with a mid-mount mower to over
ملخص المحتوى في الصفحة رقم 8
CUTTER MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this cutter does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual. Some adjustments will need to be made periodically to maintain your unit properly. BEFORE EACH SEASON A new spark plug and clean air filter assure proper air fuel mixture and help your engine run better and last longer. • Replace the spark plug. •
ملخص المحتوى في الصفحة رقم 9
GENERAL TROUBLESHOOTING The unit is not cutting level. • Level deck. Check air pressure of all tires; make sure they are equal. See tires for maximum inflation. • Without the engine running, make certain blades are installed identically. The engine will not start. • Disengage blades, turn key switch to the “OFF” position, check battery and all other electrical connections and inspect spark plug and wire. • Contact engine manufacturer or qualified mechanic. Engine runs poorly. • See engine manual
ملخص المحتوى في الصفحة رقم 10
SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. 1-800-222-8183,8-5 CT M-F OD39-SWISHER FLAG DECAL OD82-44 RUGGED CUT DECAL OD33-5MPH DECAL OD29-DANGER DECAL OD36-Deflector Decal OD55-DANGER DECAL OD10-ENGAGE DECAL OD45-WARNING DECAL OD99-OFF/RUN DECAL OD28-OFF/RUN/START DECAL 10
ملخص المحتوى في الصفحة رقم 11
FRONT SKIRT ASSEMBLY 5 FIGURE 1 2 Item # Description Part # 1 5/16-18 X 1 HCC GR5 ZP NB501 2 Metal Strap For Rubber Flap 4853TC 3 Rubber Flapper 10384 4 5/16-18 Nylock Nut NB181 1 5 Deck Weldment 10357TC 4 3 11 15 2 14 16 HITCH BAR ASSEMBLY 8 1 FIGURE 2 4 9 6 13 7 12 10 3 5 Item # Description Part # 1 Hitch Tube 4583TC 2 3/8'' -16 x 3'' GR.5 BOLT NB221 3L-Hitch H1TK 4 5/8''-11 X 1-1/2'' Bolt NB145Z 5 5/8''-11 Nylock Nut NB561 6 3/8''-16 Nylock Nut NB182 7 5/16-18 X 2 1/2 HCC GR5 ZP NB138 8 5/1
ملخص المحتوى في الصفحة رقم 12
1 FIGURE 4 4 Item # Description Part # 7 1 5/16-18 x 3/4 Serr Flg. Bolt NB596 1 2 5/16-18 x Nylock Nut NB181 3 Wheel, Tire, Bearing 4834 6 4 Back Cover 10366TK 5 Front Cover 10367TK 2 5 6 Motor Base 10343TK 9 7 Axle Bar Weldment Right 10356TK 2 19 8 Axle Bar Weldment Left 10355TK 1 17 20 9 Front Tube Weldment 10342TK 10 Deck Front 10368TC 13 11 14 11 Deck Top Weldment 10353TC 12 12 Height Adjust Rod 4006 13 Pivot Block 4007TK 18 14 15 14 1/2''-13 X 1 1/2'' HTC GR2 ZP NB588 20 15 3/4'' ID X 1 1/4
ملخص المحتوى في الصفحة رقم 13
1 NOT ACTUAL ENGINE PULLEY ASSEMBLY ENGINE USED FIGURE 6 (REF. ONLY) 1 Engine B&S N/A 2 5/16-18 Serrated Flange Nut NB170 5/16''-18 X 1 1/4'' Serrated Flange Bolt NB253 3 4 5/16'' USS Flat Washer ZP NB556 5 RT44 Belt Guide 4867 6 Spacer For Engine Pulley BB105S 7 5/16''-18 X 2 1/4 ''Flang Serr. GR5 ZP NB622 8 Engine Pulley- 4.25"OD,1 1/4'' ID BB105 3 9 1/4'' X 1'' Key Stock 9031 14 10 Spacer Lower For Engine Pulley BB105SL 11 Washer TR150W 7 9 12 Washer Belleville Engine Pulley 699 6 13 7/16''-
ملخص المحتوى في الصفحة رقم 14
CONSOLE ASSEMBLY FIGURE 8 Item # Description Part # 1 T Handle for Console 4463TK 2 1/4-20 Nylok Nut NB180 3 5/16-18 Nyloc Nut NB181 16 17 4 5/16-18 X 1 1/2 Torx Pan ZP NB591 1 15 5 Console Weldment 4575TK 10 10 6 Key Switch Lock Washer 9088 7 Key Switch Nut 9087 13 2 8 Key Switch ON-OFF, 2 Prong KSM Key Switch ( 12-VOLT ) 3623 14 9 1/4-20 X 2 1/2 HCC GR2 ZP NB141 18 10 1/4 SAE Washer NB274 3 19 12 11 Console Mount Plate 4852TK 4 12 1/4-20 Wing Nut ZP NB608 10 13 1/4 X 1 1/2 Clevis Pin NB518 5 1
ملخص المحتوى في الصفحة رقم 15
REPAIR PARTS Your 44’’ Trailcutter has been produced with components designed specific to this machine. Although standard V-belts, springs, bearings, blades, pulleys, hardware, etc. look similar to parts used on other machinery, they may in some cases be made of a different construction and/or materials. 8 10 9 7 2 1 6 5 2 4 Item # Description Part # 3 1 Battery Box 10298TK 2 Wiring Harness 10299 3 Key Switch 3623 4 Key Switch Nut 9087 5 Key Switch Lock Washer 9088 6 Decal On / Off OD28 7 T
ملخص المحتوى في الصفحة رقم 16
44”ROUGH CUT swisherinc.com TRAILCUTTER Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found on the right hand side of the motor mount. The model number for the engine will be found on the top of the blower fan housing. OWNER’S All mower parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc. or your nearest Swisher MANUAL dealer. All engine parts may be ordered from the nearest dealer of the
