ملخص المحتوى في الصفحة رقم 1
ASSEMBLY INSTRUCTIONS
OPERATOR’S MANUAL
PARTS LIST
European
Walk-Behind
Leaf Blower
Series 2
Actual product may differ slightly from product pictured above
Models Covered:
ELBC6152BV
Manual No. 7043322 (I.R. - 02/08/05) (Part # 7085926)
ملخص المحتوى في الصفحة رقم 2
1 preliminaries Congratulations! You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new blower will provide years of dependable service. Please read and follow this instruction manual carefully in order to get the most out of your new equipment. As you carefully unpack your unit, you will find the following items: 1 Blower Unit 1 Handle Assembly including: 1 – Upper Handle with foam grip 1 – Lower Handle 1 Front Caster W
ملخص المحتوى في الصفحة رقم 3
2 safety rules regarding outdoor power equipment IMPORTANT! READ CAREFULLY THE FOLLOWING SAFETY RULES BEFORE ASSEMBLING OR OPERATING UNIT. ! • Never operate with guards not securely in place. Be sure TRAINING all safety features are attached, adjusted properly and func- • Read, understand, and follow all instructions in the manu- tioning properly. al and on the unit before starting. If the operator(s) or • Never operate with the discharge deflectors removed or mechanic(s) can not read English i
ملخص المحتوى في الصفحة رقم 4
2 safety rules regarding outdoor power equipment (cont.) • Shut off fuel while storing or transporting. Do not store fuel CHILDREN near flames or drain indoors. Tragic accidents can occur if the operator is not alert to the • Keep all hardware, especially impeller bolt, tight and keep presence of children. Children are often attracted to the unit all parts in good working condition. Replace all worn or dam- and its activity. Never assume that children will remain aged decals. where you last saw
ملخص المحتوى في الصفحة رقم 5
3 unit assembly Note: Please refer to Parts List for correct part identification and placement. FRONT WHEEL ASSEMBLY • Attach left and right caster brackets to caster wheel using 3/8-18 x 2-1/4 bolt and lock nut. Insert bolt through hole in bracket. Place caster wheel onto bolt. Place other caster bracket onto bolt. Secure with lock nut. Do not over tighten. Wheel must rotate freely. • Place caster brackets onto the threaded holes located near the discharge on the front of the machine. Note: An
ملخص المحتوى في الصفحة رقم 6
4 unit operation STARTING THE ENGINE IMPORTANT NOTE: The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer’s operating instructions. In order to obtain optimum performance from your engine, refer to your engine manual. WARNING! IMPELLER IS MOUNTED DIRECTLY TO ENGINE SHAFT – STARTING ENGINE WILL RESULT IN IMMEDIATE HIGH-VELOCITY DISCHARGE. TO AVOID INJURY OR DAMAGE, BE ! SURE DISCHARGE IS POINTED AWAY FROM PEOPLE,
ملخص المحتوى في الصفحة رقم 7
4 unit operation (cont.) STARTING THE ENGINE (cont.) • Bracing unit with one hand on the upper handle and a foot on the right rear tire, firmly grasp recoil handle and pull briskly. You may have to pull several times before engine starts. (If engine fails to start within a reasonable amount of time, discontinue and check engine manual for further instructions.) Note: Do not allow recoil rope to snap back into recoil; damage to the rope or recoil could result. • After engine starts, move engin
ملخص المحتوى في الصفحة رقم 8
4 unit operation (cont.) GENERAL RULES TO OBSERVE BEFORE AND DURING OPERATION: • Inspect your unit before each and every use. Check for worn, bent or broken components, loose fasteners, low or flat tires, etc., and repair or replace prior to operation. DO NOT OPERATE A MACHINE THAT IS WORN OR DAMAGED – SERIOUS INJURY OR DEATH CAN RESULT. • Clear the entire work area of all debris that could cause damage to or become entangled in the unit. Rocks and large branches can wedge themselves betw
ملخص المحتوى في الصفحة رقم 9
5 maintenance BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT. ! GENERAL: • Follow implicitly the engine manufacturer’s recommendations for maintenance. • Always keep your machine clean – especially the engine. Check all adjustments periodically. Also, periodically check that all fasteners are secure. • Never make any adjustments to the unit until the engine is off and the spark plug wire is disconnected. • If carburetor adjus
ملخص المحتوى في الصفحة رقم 10
5 maintenance (cont.) BEFORE MAKING ANY ADJUSTMENTS, STOP ENGINE AND DISCONNECT SPARK PLUG WIRE TO PREVENT INADVERTENT STARTING OF UNIT. ! TROUBLESHOOTING: • UNIT WILL NOT START: • Check fuel and oil levels. • Check to make sure choke is set when engine is cold, off when hot. • Check throttle for proper operation. • Check intake baffle for jammed debris or accumulation of debris. • If condition persists, contact dealer. • UNIT STALLS: • Check fuel and oil levels. • Check intake baffle
ملخص المحتوى في الصفحة رقم 11
6 illustrated parts list 33 ELBC6152BV 11
ملخص المحتوى في الصفحة رقم 12
6 illustrated parts list (cont.) Item Part No. Qty Description 1 7043239 1 WELDMENT, Base & Housing 52 Classic 2 7043287 1 WELDMENT, Impeller Steel 4 Blade 15.00 O.D. 3 90167 1 SCREW, 3/8-24 x 2” Hex Head Cap, GR5 4 3020234 1 WELDMENT, Intake Baffle 5 91525 4 BOLT, 5/16-18 x 1/2” Hex Flange 6 91318 4 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR5 7 3024507 1 DEFLECTOR, Side Air 8 90188 4 WASHER, .34 x .69 x .08 Flat 9 ——- —- DECAL – See DECAL IDENTIFICATION 10 7078163 1 ROD, Door, Front/Side Discharge
ملخص المحتوى في الصفحة رقم 13
6 illustrated parts list (cont.) Item Part No. Qty Description 42 90391 4 WASHER, 5/16” Internal Tooth Lock 43 3071776 4 KNOB, Folding Handle 44 46465 1 GUIDE, Rope 45 90372 1 NUT, 1/4-20 Hex Center Lock, GR5 or B 46 3071800 1 THROTTLE CONTROL, B&S 47 90505 1 SCREW, 1/4-20 x 2” Hex Head Cap, GR5 48 76978 1 NUT, 1/4-20 Hex Nyloc 49 1717312 4 WASHER, 5/16” Curved 50 91315 4 WASHER, 5/16” Split Lock 7 decal identification 75893 - EAR/EYE/BREATHING PROTECTION REQUIRED - LOCATED ON SIDE OF BLOWER HOU
ملخص المحتوى في الصفحة رقم 14
7 decal identification (cont.) 7011279 - MODEL YEAR 2005 - LOCATED ON REAR OF BLOWER HOUSING 7078068 - NOISE RATING - LOCATED ON REAR OF BLOWER HOUSING 27255 - SNAPPER LOGO - LOCATED ON 73462 - WARNING COMBO - LOCATED INTAKE BAFFLE (ON APPLICABLE MODELS) ON TOP OF BLOWER HOUSING EUROPEAN PERFORMANCE: Maximum level of vibration measured at the operator’s hand 16 m/sec2 1722551 - SIMPLICITY LOGO - LOCATED ON INTAKE BAFFLE (ON APPLICABLE MODELS) 14
ملخص المحتوى في الصفحة رقم 15
notes 15
ملخص المحتوى في الصفحة رقم 16
ASSEMBLY INSTRUCTIONS OPERATOR’S MANUAL PARTS LIST European Walk-Behind Leaf Blower Series 2 McDonough, GA 30253 USA Manual No. 7043322 (I.R. - 02/08/05) 16
