Snapper 1691531 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION., ~-
~~~~~ INSTRUCTIONS
~
ELECTRlC L//=T KIT
MFG. NO. 1691531
i ;
For use with a// mounted attachments
KIT PARTS
~
on 6500/1800 Series Tractors
Mount to
Mount to top
capscrew on lift lever
support bracket.
ignition wire.
Used for rear attachments
onlv. Use item Q for mowers.
FRONT
J
Fiigure 1. Kit Parts
Part No. oty.
Description Part No. my. Item Description
Item
N Pin, Quick 1960033 3
A Harness Assy.. Elec. Lift 1702082 1
8 Switch, Electric 171883 1 0 Hub Assy.. Wheel 1701914 1
170

ملخص المحتوى في الصفحة رقم 2

Remove rear right-hand wheel assembly. Remove tive capscrews from wheel assembly and WARNING A secure kit hub assembly (0, figure 1) to wheel. Do not Before installing the kit or making any adjustments: install on tractor. disengage the PTO; set the parking brake; stop the engine and remove the key. Prepare template (provided on last page) by cutting out all dashed areas. Use this template to drill five 1 l/32” holes in wrapper. Install rear actuator bracket (X, figure 1 or A, figure WARNING A 2

ملخص المحتوى في الصفحة رقم 3

Figure 5. Electric Lift Lever Figure 3. Cylinder ~lnstallation A. Lift Lever Bracket A. Cylinder S. Bracket Support 6. Lugs c. capscrew c. 4-l/2” Capscrew D. Wire Clip D. 1” Capscrew (from inside out) E. Actuator Link F. Clevis Pin 12. Remove the manual lift lever as follows: G. Spring Clip a. Remove the two capscrews and lockwashen (B, figure 4). Leave the retaining nuts in place. capscrews, b. Remove the lever by removing four 14. Reinstall bracket support (B), reusing existing lockwashers an

ملخص المحتوى في الصفحة رقم 4

20. Remove the upper and lower dash hardware as follows. a. Remove the two screws (C, figure 6) and washers. b. Raise the hood and loosen the two screws, plain : washers, dished washers and nuts from front side of dash (see figure 8). c. Remove four capscrews and washers securing lower dash. d. Both dashboards can now be lifted up for access to wiring. 21. Remove the ignition switch by removing nut. Retain lockwasher for reinstallation. 22. Reach thru the hole in top of lower dash and install th

ملخص المحتوى في الصفحة رقم 5

REAR-MOUNTED ATTACHMENTS - LIFT ROD INSTALLATION Lift rod (L, figure 1) is used only for rear mounted attachments. To install, remove bottom clevis pin (Q) and install lift rod (A, figure 9) to actuator link(B) and lift arm (C). Secure with clevis pins (D) as shown. Figure 8. Upper UaSn I _ 29. Align the steering wheel and push down onto shaft. 30. Reinstall capscrew (C, figure 7), flat washers, and locknuts to secure steering wheel. Torque nut to 10 ft. Figure 9. Lift Rod Ibs. A. Lift Rod 31.

ملخص المحتوى في الصفحة رقم 6

i i I I .-. 1 / ! ‘1 \ \ ./ \ \ \ \ \ I \ 1 I \ I 1 1 \ t I I t \ l Align with holes In rlght I I I ’ Align with holes In rlght hand side of axle support; \ “hand side of axle support :---m ----I wrapper - two places \ I wrapper - two places \ (remove bolts and reinstall Al (remove bolts and f ,’ If necessary). I’ reinstall If necessary). ---_ I’ CUTOU’r (TEMPLATE ONLY) --I’ ON DOTTED LINE.