ملخص المحتوى في الصفحة رقم 1
ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep
Triple Catcher
Clean Sweep Twin Catcher
Mfg. No. Description
1694918 Clean Sweep Triple Catcher
1732353
Rev. 00
Rev. Date 02/2006
TP 100-4265-00-AT-SMAN
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Table of Contents Safety Rules & Information Normal Removal & Installation General Warnings............................................2 Collector Installation ......................................10 Safety Decals ..................................................2 Collector Removal .........................................11 Storing the Grass Catcher...............................3 NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position. General Ope
ملخص المحتوى في الصفحة رقم 4
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. GENERAL WARNINGS � Know the unit’s controls and how to stop quickly. � If the mower stalls or the collector chute plugs: READ THE OPERATOR’S MANUALS. 1. Disengage the
ملخص المحتوى في الصفحة رقم 5
General Operating Instructions Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the u
ملخص المحتوى في الصفحة رقم 6
Initial Installation WARNING Before beginning any service work turn off the B PTO, set the parking brake, turn off the ignition, A and disconnect the spark plug wire(s). Initial Installation HITCH INSTALLATION A 1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear frame support (E) through square hole (C) so that the threaded side (B) is on the inside of tractor. C E 2. Secure the 5/16-18 shoulder bolt (D) as shown. D 3. Repeat on the other side. Figure 1. Install Spacer (left side shown) A.
ملخص المحتوى في الصفحة رقم 7
Tube Component Assembly Baffle Installation 44” Mower Deck 50” Mower Deck 1. Determine which baffle to use. See Figure 3 Chart. “A” RH side 26-1/4” long RH side 29-3/4” long 2. Lift side discharge chute (H, Figure 3). 3. Insert baffle (F) through discharge opening and posi- “B” LH side 24-7/8” long LH side 27-3/4” long tion baffle into place. 4. Tighten carriage bolts (A) and nuts (E) on baffle (F). 5. Tighten carriage bolt (B) and nut (E) on baffle (F). 6. Position baffle (G) into place. 7. Ti
ملخص المحتوى في الصفحة رقم 8
Baffle Installation C B A D A C E F B G G H J I Figure 4. Install Mounting Plate A. Mounting Plate Figure 5. Lower Chute to Boot Installation B. Locknuts, 5/16-18 A. Pin, Latch C. Carriage Bolts, 5/16-18 x 5/8 B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 Component Installation D. Lower Chute E. Locknut, Center Lock, 5/16-18 INSTALL MOUNTING PLATE F. Strap, Rubber 1. Install mounting plate (A, Figure 4) to mower deck as G. Locknuts, Whiz Lock, 5/16-18 shown. Secure with 5/16-18 x 5/8 carr
ملخص المحتوى في الصفحة رقم 9
Install Latch & Hinge C A A B D F F C E B G Figure 8. Install Channel Assembly A. Channel Assembly B. Hitch Figure 7. Install Latch & Hinge to Cover Assembly C. Pin A. Cover Assembly B. Latch C. Locknuts, ESNA, #10-24 D. Screws, #10-24 x 5/8 E. Hinge C F. Locknuts, 1/4-20 G. Screws, Slotted, 1/4-20 x 1/2 A E INSTALL LATCH AND HINGE TO COVER ASSEMBLY 1. Install the latch (B, Figure 7) to the cover assembly B (A) securing with #10-24 x 5/8 screws (D) and #10-24 B locknuts (C) as shown. D 2. Ins
ملخص المحتوى في الصفحة رقم 10
Initial Hitch & Tube Installation C F C E F C A F F C D B D D C F B E D D A B F Figure 11. Install Cover to Channel Assembly Figure 10. Install Tubes and End Caps A. Cover A. Cross Bar B. Pin B. Tubes C. Hair Pin C. Capscrews, 5/16-18 x 2 D. Channel Assembly D. Locknuts, Center Lock, 5/16-18 E. Square End Plugs F. Round End Plugs A B INSTALL TUBES AND END PLUGS 1. Install the tubes (B, Figure 10) to cross bar (A) secur- ing with 5/16-18 x 2 capscrews (C) and 5/16-18 lock- nuts (D). 2. Install
ملخص المحتوى في الصفحة رقم 11
Tube Installation D C D C E B A B A Figure 15. Install Upper Tube to Cover A. Upper Tube B. Cover Figure 14. Install Lower Tube C. Ridge, Upper Tube A. Lower Chute Rod D. Ridge Cutout B. Mounting Plate C. Rubber Strap D. Discharge Deflector E. Locknut E LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 14). 2. Insert lower chute rod (A) into mounting plate (B). D 3. Pull rubber strap (C) and secure by placing hole clos- est to knob in strap completely over locknut (E). CONNECT
ملخص المحتوى في الصفحة رقم 12
Normal Removal & Installation F E Q P O R A S C B N D M A. Channel Assembly K. Lower Chute Rod B. Cover L. Lower Chute H I C. Pin M. Pin L D. Hitch N. Strap, Middle G E. Bag O. Upper Tube F. White Bar P. Ridge G. Nut & Capscrew Q. Ridge Cutout K H. Deflector R. Tubes, Bag Support I. Strap, Boot S. Middle Tube J J. Mounting plate Figure 17. Normal Installation & Removal Normal Removal & Installation by placing hole closest to knob in strap completely over locknut and capscrew (G). Collector Inst
ملخص المحتوى في الصفحة رقم 13
Normal Removal Collector Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. 1. Unhook strap (N) from pin (M). Slide middle tube into upper tube (O) and remove middle tube (S). Remove upper tube (O) from cover (B). 2. Lift up cover (B) remove and empty bags (E). 3. Unhook strap (I) from locknut and capscrew (G). Remove lower chute (L) from mounting plate (J). See that the di
ملخص المحتوى في الصفحة رقم 14
ملخص المحتوى في الصفحة رقم 15
ملخص المحتوى في الصفحة رقم 16
MANUFACTURING, INC. Simplicity Mfg. Inc.500 N Spring Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Street / PO Box 997 Port Washington, WI 53074-0997 Port Washington, WI 53074-0997 www.AGCOLawn.com www.SimplicityMfg.com Simplicity Mfg. Inc. - Snapper Products Simplicity Mfg. Inc.500 N Spring 535 Macon Street Street / PO Box 997 McDonough, GA 30253 Port Washington, WI 53074-0997 www.Snapper.com www.MasseyLawn.com © Copyright 2006 Simplicity Manufacturing, Inc. All Rights Reserved. Prin