ملخص المحتوى في الصفحة رقم 1
OPERATOR’S MANUAL
MODEL GC-STC-CS
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TION FOR YOUR SCAG ACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURES TO KEEP YOUR ACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE, PLEASE READ ALL THE INFORMA-
TION ENCLOSED.
PART NUMBER 03156
ملخص المحتوى في الصفحة رقم 2
WARNING FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all safety shields in place. * Before performing any maintenance or service, stop the machine and remove the spark plug wire. * If a mechanism becomes clogged, stop the engine and wait for all moving parts to come to a complete halt before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as the Operator's Manual that came with your
ملخص المحتوى في الصفحة رقم 3
A replacement manual is available from your 1.1 INTRODUCTION authorized Scag Service Dealer or by contacting: Scag Power Equipment, Service Department at P.O. This manual has been prepared to provide the Box 152, Mayville, WI 53050. You may also contact information you need to correctly assemble, operate, us through our website at www.scag.com The and maintain this grass catcher. Read it carefully and manual for this grass catcher can be downloaded by keep it for future reference. using the m
ملخص المحتوى في الصفحة رقم 4
5. To clean the hopper debris screen; 3. When dumping the hopper into a disposal area: A. Disengage the deck drive and allow all WARNING WARNING moving parts to come to a complete stop. DO NOT DUMP CLIPPINGS IN A DISPOSAL AREA THAT IS BURNING B. Apply parking brake and shut off the engine. A. Disengage the deck drive, apply the parking C. Stand on the left side of the hopper brake and allow all moving parts to come to assembly. a complete stop. D. Unhook the debris screen latches and B. Pul
ملخص المحتوى في الصفحة رقم 5
3.1 ASSEMBLY INSTRUCTIONS FOR 48" -NOTE- AND 52" CUTTER DECK When installing this grass catcher on a machine with a serial number range from 7630001 to 8479999, you will need to install part number -NOTE- Use the illustrated parts list as a part number 461764 for a 48" cutter deck or 461765 for a 52" cutter deck. This kit includes a new Turbo reference when following the assembly Baffle and Deck Baffle. instructions. 1. Remove all packaging materials. Lay out the 4. Install the grass cat
ملخص المحتوى في الصفحة رقم 6
FLATWASHER ELASTIC STOP NUT CARRIAGE BOLT FIGURE 3-2 BLOWER ASSEMBLY HAIR PIN MOUNTING BRACKET TIGHTEN P R O P E R Y L CATCH PLATE S E C R E V I HARDWARE E N N G E I W T H I O L I MOUNTING PIN A N D F U E L . TIGHTEN MOUNTING BRACKET HARDWARE RIGHT SIDE OF CUTTER DECK SHOWN (Note: Some parts not shown for viewing purposes.) 2005 GC-STC install art 3 FIGURE 3-3 4
ملخص المحتوى في الصفحة رقم 7
10. Install the new belt covers and secure. See -NOTE- items number 1 and number 21 on page 10 of the The hopper dump handle can be installed on Blower Mounting Components section in the either side for operator convenience. When Illustrated Parts List for proper installation. installing this grass catcher on a machine with the Roll Over Protection System (ROPS), 11. Install the hopper mounting brackets to the the curved handle will need to be installed on outside of the frame on the rear of th
ملخص المحتوى في الصفحة رقم 8
4.1 GRASS CATCHER REMOVAL INSTRUCTIONS 5. With help from an assistant, remove the hopper 1. Prepare the work area making sure that it is a assembly from the mounting posts. clean, safe environment. 2. Remove the rubber strap holding the adapter to the blower assembly. See Figure 4-1. WARNING WARNING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING 3. Remove the pin and hair pin holding the blower KIT, OR ENTIRE GRASS CATCHER INSTALLED assembly to the mounting bracket on the cutter deck and
ملخص المحتوى في الصفحة رقم 9
Notes 7
ملخص المحتوى في الصفحة رقم 10
WARNING INSTALL BELT COVER BEFORE OPERATING MACHINE READ OPERATOR'S MANUAL DANGER ROTATING BLADES AND BLOWER Stop engine before cleaning or removing DO NOT OPERATE MOWER UNLESS GRASS CATCHER OR DISCHARGE GUARD IS INSTALLED GC-STC 48" & 52" BLOWER HOUSING ASSEMBLY 9 48 10 11 12 13 2 4 8 1 9 5 3 11 6 7 10 10 14 44 47 27 14 12 11 15 43 16 14 42 15 26 17 41 39 40 18 34 27 19 17 25 28 20 21 41 38 22 3 35 27 23 51 24 46 14 24 14 29 50 30 33 32 37 31 31 45 47 2005 GC Blower Assembly 45 35 34 49 8 D DA
ملخص المحتوى في الصفحة رقم 11
GC-STC 48" & 52" BLOWER HOUSING ASSEMBLY Ref. Part Ref. Part No. Number Description No. Number Description 1 04067-07 Pin, Ring 2-1/4" Long 27 04019-04 Nut, Serr. Flange 3/8-16 2 481547 Lanyard, Deck Height Pin 28 04001-136 Bolt, Hex Head 3/8-16 x 1-1/2 Gr. 8 3 04019-02 Nut, Serr. Flange 1/4-20 29 481377 Decal, Danger 4 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 30 461681 Blower Housing Assembly 5 04001-01 Bolt, Hex Head 1/4-20 x 3/4" 31 04003-12 Bolt, Carr. 5/16-18 x 3/4" Gr. 5 6 42329
ملخص المحتوى في الصفحة رقم 12
GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS FOR MACHINES WITH A SERIAL NUMBER BETWEEN 7630001 - 8479999 ONLY 31 30 24 10 23 25 25 6 26 10 26 11 5 29 2 28 4 32 6 1 7 27 8 29 27 3 28 6 9 UNDER SIDE OF 13 12 CUTTER DECK SHOWN 21 14 15 22 15 20 16 18 17 19 RIGHT SIDE OF CUTTER DECK SHOWN 390STC203B 10
ملخص المحتوى في الصفحة رقم 13
GC-STC 48" & 52" BLOWER MOUNTING COMPONENTS Ref. Part No. Number Description 1 482612 Belt Cover, GC-STC 2 04029-04 Wingnut, Plastic 3/8" Small 3 482300 Cap, Square Vinyl 4 04021-08 Nut, Elastic Stop 1/4-20 5 461723 Adapter, Blower GC-STC, includes item #7 6 04040-14 Flatwasher, 1/4-.312 x .750 x .065 7 48137-04 Rubber Strap 7-3/4" 8 04001-59 Bolt, Hex Head 1/4-20 x 1-1/4" 9 481625-01 Knob W/Stud, 3/8-16 x 1-1/4" 10 04064-15 Clevis Pin, 5/16 x 1-1/2" 11 04069-03 Pin, Rue Cotter 5/16 Dia. 12 0406
ملخص المحتوى في الصفحة رقم 14
GC-STC-CS HOPPER COMPONENTS 16 14 49 50 5 4 3 45 45 41 15 31 43 11 17 51 56 55 40 8 58 59 12 9 25 29 6 33 34 10 53 2 50 49 34 B 49 42 24 55 27 49 6 53 61 43 37 48 60 36 18 38 19 63 53 49 C 34 49 50 20 52 54 41 49 12 18 49 49 53 53 66 60 7 65 70 A 61 58 33 59 24 28 1 49 64 62 10 34 21 38 32 49 69 30 49 63 38 35 45 46 22 37 49 49 13 33 36 25 49 57 49 21 C 23 33 68 26 38 58 32 40 53 44 49 20 65 B 59 53 46 33 64 19 66 A 65 67 71 29 57 46 58 60 59 28 49 71A 61 49 61 35 49 46 26 37 37 60 2005 CSHOPPE
ملخص المحتوى في الصفحة رقم 15
GC-STC-CS HOPPER COMPONENTS Ref. Part Ref. Part No. Number Description No. Number Description 1 461627 Hopper, GC-STC-CS 40 04001-77 Bolt, Hex Head 3/8-16 x 3-1/2" 2 482732 Door, GC-CS 41 04003-04 Bolt, Carriage 5/16-18 x 1" 3 461626 Sweeper Weldment, GC-CS 42 04010-01 Screw, #10-32 x 1/2" 4 482777 Pad, Rubber 43 04017-16 Cap Screw, 5/16-18 x 3/4" Serr. Flan. 5 04090-02 Pop Rivet, 3/16 x .652 44 04017-17 Cap Screw, 5/16-18 x 1" Serr. Flan. 6 423834 Plate, Stiffener 45 04019-03 Nut, 5
ملخص المحتوى في الصفحة رقم 16
GC-STC-CS DECALS 481039 482275 481327 481377 483037 483039 14
ملخص المحتوى في الصفحة رقم 17
LIMITED WARRANTY- COMMERCIAL ACCESSORY Any part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag, to be defective in material or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. The Scag accessory, including any defective part, must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the accessory to the dealer for warranty work
ملخص المحتوى في الصفحة رقم 18
© 2004 PART NO. 03156 SCAG POWER EQUIPMENT PRINTED 8-2004 DIVISION OF METALCRAFT OF MAYVILLE, INC PRINTED IN USA www.scag.com
