ملخص المحتوى في الصفحة رقم 1
Operator and Parts Manual
Collection System
M-ZT 52 /966793002
M-ZT 61 /966793003
ملخص المحتوى في الصفحة رقم 2
CONGRATULATIONS on the purchase of a new KNOW YOUR BLOWER SYSTEM collection system. It has been designed, engineered READ THIS OPERATION MANUAL AND SAFETY and manufactured to give you the best possible RULES BEFORE ASSEMBLING OR OPERATING THE dependability and performance. BLOWER SYSTEM. Compare the illustrations with the Should you experience any problem you cannot easily carton contents and become familiar with the parts remedy, please contact the nearest authorized service before start
ملخص المحتوى في الصفحة رقم 3
CONTENTS SAFETY RULES .........................................................4 ASSEMBLY ................................................................5 OPERATION ............................................................. 11 BLOWER ASSEMBLY ......................................12 CHUTES ...........................................................14 BAGGER ..........................................................16 MOUNT, GUARD, BELT ...................................18 TOOLS REQUIRED CON
ملخص المحتوى في الصفحة رقم 4
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS GENERAL OPERATION • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine. Tall grass can hide • Read, understand and follow all instructions in the obstacles. manual and on the machine before starting. • Use slow speed. Choose a low speed so that you • Only allow responsible adults, who are familiar will not have to stop while on the slope. with the instructions, to operate the machine. • Keep all movement on the
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY DRIVE PULLEY TRIMMING BLOWER 1 2 1. Remove the discharge chute from the deck 1. Place blower assembly on secure table or stable by removing the side hardware from the chute surface. bracket. Retain the hardware for reuse if the 2. Remove the bolts securing the rear mount collection system is removed. bracket. 2. Lower deck to the lowest cutting position. 3. Using the hacksaw, trim the blower housing along 3. Remove the right hand (discharge side) belt cover the recessed grooves. fro
ملخص المحتوى في الصفحة رقم 6
ASSEMBLY DRIVE BELT BELT COVERS 4 5 1. Make sure the tension release lever is forward 1. Place the deck belt shield on the deck over the (disengaged). drive pulley and secure with hardware removed from steel belt shield. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 2. Place retainer on the outer pulley cover. 3. Move the tension release arm to the rear and 3. Align the tab end of the belt cover into the slot on engage in the latch. the deck belt s
ملخص المحتوى في الصفحة رقم 7
ASSEMBLY BAGGER MOUNT 6 4. Install the mount straps (bends are to the inside) 1. Using 1¾" round head shoulder bolts and nuts, on the outside of the mount tube using 2" hex attach the mount hitch to the mount tube as bolts and nuts. The front side of the mount straps illustrated. Make sure the elbowed arm of the tube are secured to the fuel tank brackets with 1" round is on the right side, with the mount hitch installed head shoulder bolts and nuts. to the front. 2. Attach the support b
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY CHUTE SUPPORT COVER ASSEMBLY 7 8 1. Position upper chute support against bagger inlet, NOTE: For ease of assembly, you may wish flush at outer edges. See Illustration. assistance from another person for mounting 3 the cover assembly to mower. 2. Using support as a template, drill two /8 holes into bagger hood. 1. Position cover assembly on ground behind mower. 2. Lift and rotate cover to align the cover brackets with support assembly tubes. 3. Slide the cover down over the support
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY UPPER CHUTE ASSEMBLY CHUTE / HOOD INSTALLATION 10 11 1. Slide upper chute onto middle chute, lining up the Push upper chute through the gasketed opening in middle chute latch and the acorn nut on the upper the cover assembly. chute. 2. Stretch bungee latch up onto acorn nut to secure. Cover Inlet Upper Chute 9
ملخص المحتوى في الصفحة رقم 10
ASSEMBLY WEIGHT ASSEMBLY 12 6. Fasten the three weight plates to the weight 1. Remove the foot plate knob and foot plate. Set brackets. aside for later reuse. 2. Remove and reserve the three rubber grommets from the foot rest. 3. Remove the foot rest for replacement. Retain hardware for reuse. Foot Plate Foot Rest 4. Install the three rubber grommets to the new foot 7. Secure the weight plate assembly to the front rest and fasten the assembly to the frame with the frame of the mower bet
ملخص المحتوى في الصفحة رقم 11
OPERATION TIPS FOR IMPROVED BAGGING • If the grass catcher fails to pick up cut grass • Follow the mower operation instructions in you or leaves, it is an indication that clogging has mower operator manual. occurred in the system or that the grass catcher • When operating the grass catcher on a lawn containers are full. where grass and leaf bagging equipment has not been used, thatch and debris that has a. Disengage blades, place motion control levers accumulated for long periods of time
ملخص المحتوى في الصفحة رقم 12
REPAIR PARTS BLOWER ASSEMBLY 46 24 65 34 18 51 16 12 28 19 58 32 3 53 61 43 62 13 4 56 44 59 60 9 1 11 13 37 14 8 23 58 63 40 52 21 45 41 40 63 6 50 10 32 50 58 57 5 33 58 7 17 22 2 60 15 49 48 31 65 20 35 59 64 47 12 64 25 53 54 55 56 63 27 26 30 48 50 66 38 42 29
ملخص المحتوى في الصفحة رقم 13
REPAIR PARTS ITEM ITEM P PAR ART T NO. NO. QTY QTY. . DESCRIPTION DESCRIPTION ITEM ITEM P PAR ART TNO. NO. QTY QTY . . DESCRIPTION DESCRIPTION 33.. 539 130296 .... 2 ....BEARING 1.. 539 130344 .... 1 ....HOUSING w/DECALS 34.. 522 909602 .... 1 ....BRACKET, MOUNT 2.. 539 130293 .... 1 ....COVER, BELT 35.. 522 909502 .... 1 ....BRACKET, RETENTION 3.. 574 411501 .... 1 ....COVER, BELT 36.. 525 618302 .... 1 ....SAND LINER, TOP 4.. 539 130292 .... 1 ....IMPELLER 37.. 522 909702 ..
ملخص المحتوى في الصفحة رقم 14
REPAIR PARTS CHUTES 3 7 2 12 1 10 11 4 9 11 5 5 11 9 6 8 8 14
ملخص المحتوى في الصفحة رقم 15
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 5 1.. 539 108141 .... 1 ....CHUTE, UPPER 7.. 539 976952 .... 1 ....SCREW #10-24 x /8 1 2.. 539 130294 .... 1 ....CHUTE, MIDDLE 8.. 539 108083 .... 2 ....SCREW #10-24 x 1 /8 3.. 539 130933 .... 1 ....INDICATOR, BAG DUMP 9.. 539 108086 .... 2 ....NUT #10-24 ACORN 4.. 539 108088 .... 1 ....LATCH, HOOD 10.. 539 108089 .... 1 ....WELDNUT, PLATED 3 5.. 539 108085 .... 2 ....SPACER, SPLIT 11.. 539 108084 .... 3 ....WASHER
ملخص المحتوى في الصفحة رقم 16
REPAIR PARTS BAGGER 1 16 3 8 9 14 16 5 11 15 13 17 10 15 7 6 4 12 2 16
ملخص المحتوى في الصفحة رقم 17
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 1.. 532 195373 .... 1 ....COVER 10.. 539 110281 .... 1 ....SUPPORT, CHUTE 2.. 532 400226 .... 3 ....CONTAINER, SOFT BAG 11.. 539 112294 .... 1 ....FLEX TRIM 3.. 532 130895 .... 2 ....HANDLE, BAGGER COVER 12.. 539 108096 .... 2 ....HAIR PIN 5 4.. 532 176990 .... 1 ....FRAME, BAGGER 13.. 539 990627 .... 2 ....HCS /16-18 x 1¼ 5 5.. 532 192709 .... 1 ....SCREEN, COVER 14.. 539 976952 .... 6 ....SCREW #10-24 x /8 5 6..
ملخص المحتوى في الصفحة رقم 18
REPAIR PARTS MOUNT, GUARD, BELT 10 2 1 23 4 18 27 22 9 3 12 14 21 22 25 19 13 8 11 25 7 24 17 28 6 16 15 25 20 5 26 17 18
ملخص المحتوى في الصفحة رقم 19
REPAIR PARTS ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 15.. 576 221502 .... 1 ....SPACER 1.. 539 130307 .... 1 ....SHIELD, BELT, 52" 3 16.. 539 990645 .... 2 ....RHSNB /8-16 x 1 539 130308 ...1 .... SHIELD, BELT, 61" 5 17.. 539 990861 .... 4 ....RHSNB /16-18 x 1¾ 2.. 539 130320 .... 1 ....PULLEY, 52" 3 18.. 539 101341 .... 4 ....HCS /8-16 x 3 539 130321 ...1 .... PULLEY, 61" 3 19.. 539 102334 .... 4 ....HCS /8-16 x 4½ 3.. 539 130347 .... 1 ....BELT 52" 20.. 539 990646
ملخص المحتوى في الصفحة رقم 20
115 584027 Rev A 2013-02-15
