ملخص المحتوى في الصفحة رقم 1
Rider 11/13 H
Operator´s manual
Please read these instructions carefully and make sure
you understand them before using the machine.
101 90 52-95
ملخص المحتوى في الصفحة رقم 2
Svenska – 31 Sve-5 225/232/235 Bruk 31 97-11-25, 08.46
ملخص المحتوى في الصفحة رقم 3
CONTENTS Operator’s Manual for Rider 11 and Rider 13 H Explanation of symbols ...................................... 2 Cutting tips ..................................................... 17 Safety instructions .............................................. 3 Stopping the engine ....................................... 18 General operation ............................................ 3 Maintenance ...................................................... 19 Slope operation ............................
ملخص المحتوى في الصفحة رقم 4
EXPLANATION OF SYMBOLS These symbols are on the machine and in the operator’s manual. Study them carefully so that you know what they mean. Read the operator’s manual R N Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil pressure Cutting height Backwards Forwards Ignition Hydrostatic free wheel ! Use eye and Clutch in Clutch out Parking brake Brake Clutch Warning hearing protection Soundlevel Warning! Warning! Never drive across a slope European standard for Rotating bl
ملخص المحتوى في الصفحة رقم 5
SAFETY INSTRUCTIONS These instructions are for your safety. Read them carefully. 1. Safety rules for USA !! Safe operation practices for ride-on mowers IMPORTANT! This cutting machine is capable of amputating hands and feet and throwing objects. Failure to ob- serve the following safety instructions could result in serious injury or death. Use slow speed. Choose a low gear so that I. General operation you will not have to stop or shift while on the 1. Read, understand and follow all instructions
ملخص المحتوى في الصفحة رقم 6
SAFETY INSTRUCTIONS Travel and transport on public roads IV. Service Check the relevant road traffic regulations before 1. Use extra care in handling gasoline and other driving the machine on a public road. If transporting fuels. They are flammable and vapours are the machine on another vehicle always use ap- explosive. proved securing devices and make sure that the machine is securely held. a) Use only an approved container. Towing b) Never remove gas cap or add fuel with the If your machine ha
ملخص المحتوى في الصفحة رقم 7
R R RIDER II D D E E R R 9 9 970 7 7 0 0 R R R R RIDER RIDER IIII D D D D E E E E R R R R 8 8 8 8 850 850 5 5 5 5 0 0 0 0 SAFETY INSTRUCTIONS This symbol implies that important safety rules are applicable. This is for your safety and the operating reliability of the machine. ! General use: • Make yourself familiar with the controls and how to stop quickly. • Read all the instructions in Operator’s Manual and on the machine before starting it. Make sure you understand them, and then follow t
ملخص المحتوى في الصفحة رقم 8
SAFETY INSTRUCTIONS • Watch out for traffic when working close to a road, or crossing one. • Be careful when rounding a fixed object so that the blades do not hit it. Never drive intentionally over a foreign object. • The machine is heavy and can cause very severe crush injuries. Be extra careful when loading it on a trailer or truck. • Be careful when pulling a load or using heavy equipment. a. Only use approved tow hooks. b. Limit the load to what you can manage safely. c. Do not make sharp tu
ملخص المحتوى في الصفحة رقم 9
RIDER R RID ID E E R R 9 9 970 7 7 0 0 RIDER RIDER R R R R II II D D D D E E E E R R R R 8 8 8 8 850 850 5 5 5 5 0 0 0 0 SAFETY INSTRUCTIONS • Do not cut close to edges, ditches or banks. The machine can suddenly tip over if a wheel goes over the edge of a drop or a ditch, or if a bank gives way. • Do not cut wet grass. It is slippery and the tyres can loose their grip so that the machine slides. • Do not try to stabilise the machine by placing one foot on the ground. Children Tragic acci
ملخص المحتوى في الصفحة رقم 10
RIDER RIDER R R R RID ID ID ID E E E E R R R R 8 850 850 8 8 8 5 5 5 5 0 0 0 0 R R RIDER I I D D E E R R 9 9 970 7 7 0 0 SAFETY INSTRUCTIONS • Avoid overfilling. If fuel has been spilt on the machine wipe it up and wait until it has evapor- ated before starting the engine. If fuel is spilt on clothes, change them. • Be extra careful when handling battery acid. Spilling acid on the skin can cause severe burn injuries. Rinse immediately with water. If acid gets into the eyes this can cause
ملخص المحتوى في الصفحة رقم 11
PRESENTATION Presentation Congratulation on your choice of a first-class quality product. These instructions describe two models of Rider mower, Rider 11 and Rider 13 H. Both models are fitted with engines from Briggs & Stratton of 10.5 and 12.5 horsepower respectively, plus a cutting unit which throws out grass at the rear of the machine. Rider 11 has an in-line gearbox with five forward gears and one reverse gear. On the Rider 13 H the power transmission from the engine is handled by a hydrost
ملخص المحتوى في الصفحة رقم 12
PRESENTATION Throttle and Choke lever Rider 13 H The engine speed is adjusted with the throttle control, and thereby also the rotation speed of the blades. The control is also used to activate the choke function. When the choke is used the engine receives a richer mixture of fuel and air, which simplifies cold start. Speed limiter Rider 13 H The speed of the machine is steplessly regulated 2 1 with two pedals. Pedal (1) is used to drive forwards and pedal (2) for reversing. Parking brake Rider 1
ملخص المحتوى في الصفحة رقم 13
PRESENTATION Throttle and Choke lever Rider 11 The engine speed is adjusted with the throttle control, and thereby also the rotation speed of the blades. The control is also used to activate the choke function. When the choke is used the engine receives a richer mixture of fuel and air, which simplifies cold start. Clutch pedal Rider 11 The clutch pedal disengages the engine and stops forward movement. The blades are not affected by the clutch pedal. Brake pedal / Parking brake Rider 11 The bra
ملخص المحتوى في الصفحة رقم 14
PRESENTATION Cutting unit Rider 11 and Rider 13 H have a cutting unit with rear ejection, i.e. the grass cuttings are thrown out behind the cutting unit. Lift lever for cutting unit The lift lever is used to set the cutting unit in trans- port or cutting position. If the lever is pulled back the unit will lift up and the blades stop rotating (transport position). If the lock button is pressed and the lever is moved forward the unit will lower down and the blades begin rotating (cutting position)
ملخص المحتوى في الصفحة رقم 15
PRESENTATION Seat The seat has a jointed attachment on the front edge and can be tipped forward. The seat can also be adjusted lengthways. Release the wheels under the seat and adjust it forwards or backwards to the required position. Lock the adjustment with the wheels. Fuelling The engine should be run on 85 octane unleaded petrol/gasoline (not oil mixed). WARNING! Petrol/gasoline is highly inflammable. ! Observe care and fill up with fuel outdoors (see safety instructions). English – 13
ملخص المحتوى في الصفحة رقم 16
DRIVING Before starting • Read the safety instructions and information on the location and function of the controls before starting (see pages 3–13). • Conduct daily maintenance before starting (see maintenance schedule on page 19). Adjust the seat to the required position. Starting the engine 1. Lift up the cutting unit by pulling the lever back- wards to locked position (transport position). 2. Apply the parking brake. This is done as follows: 2 • Press down the brake pedal (1). • Press in the
ملخص المحتوى في الصفحة رقم 17
DRIVING Cold engine: 4. Push the throttle control to position 3 (choke position). In this position the engine receives a 2 richer mixture so that the engine starts more 1 easily. 3 Warm engine: 5. Set the throttle control midway between position 1 and 2. 2 1 3 6. Turn the ignition key to start position. STOP START IMPORTANT INFORMATION Do not run the starter for more than about 5 seconds at a time. If the engine does not start, wait about 10 seconds before trying again. English – 15
ملخص المحتوى في الصفحة رقم 18
DRIVING 7. When the engine has started release the ignition key to neutral position. Push the throttle control to the required speed. For cutting 3/4 to full throttle. STOP START WARNING! Never run the engine indoors, in ! enclosed or poorly ventilated areas. The exhaust fumes contain toxic carbon monoxide. Driving the machine 1. Release the parking brake by pressing down the brake pedal. The drawing shows a Rider 13 H. 2. For Rider 13 H Carefully press down one of the pedals until the 1 2 corre
ملخص المحتوى في الصفحة رقم 19
DRIVING 3. Select the required cutting height (1-9) with the cutting height lever. To obtain a uniform cutting height it is important that the tyre pressures are equal on both front wheels (60 kPa). 4. Push in the lock button on the lift lever and lower down the cutting unit. IMPORTANT INFORMATION The service-life of the drive belts increases considerably if the engine is run at low speed when engaging the blades. For this reason do not increase the throttle until the cutting unit has been lower
ملخص المحتوى في الصفحة رقم 20
DRIVING WARNING! Never drive the machine on ground ! with a slope of more than 15°. Mow slopes upwards and downwards, never across. Avoid sudden changes in direction. Hill start, manual gearbox 1. Press down the parking brake. 2. Push the throttle control to 3/4 position to full MAX 15° throttle position. 3. Push down the clutch and engage first gear. 4. Carefully release the clutch. 5. When the engine starts to pull, release the parking brake. Stopping the engine Preferably allow the engine to
