ملخص المحتوى في الصفحة رقم 1
Sub-Frame Hitch
Installation
Mfg. No. 1695196
For Prestige / 1800 / 2800, Conquest / 1700 / 2700, &
Instructions
Broadmoor / 1600 / 2600 Series Tractors
This kit is required when installing front mounted
snowthrowers.
1
ملخص المحتوى في الصفحة رقم 2
Installation Instructions Sub-Frame Hitch Main Hitch Components (All Applications) 28 29 27 30 25 29 41 33 39 38 40 37 36 35 42 1 2 3 28 27 33 51 43 25 33 25 33 29 25 27 25 34 4 28 28 26 27 28 27 25 22 5 27 30 28 31 50 32 22 6 46 25 45 49 7 24 48 8 23 9 15 9 9 47 17 16 10 18 13 21 Front Hole for Dozer Applications Hydraulic Rear Hole for Snowthrower Applications 20 Lift 14 11 13 19 Early Manual 12 11 Lift Only (See Instructions) 9 Figure 1. Contents 2
ملخص المحتوى في الصفحة رقم 3
Sub-Frame Hitch Installation Instructions Ref Part No. Qty. Description 1 1723292A 1 SHAFT & HOOK ASSY 2 1653768A 1 CLAMP, Support 3 1931335 4 CARRIAGE BOLT, 5/16-18 x 1 4 1919381 4 WASHER, 11/32 5 1917356 3 LOCKWASHER, 5/16 6 1917372 4 NUT, 5/16-18 7 105249 1 PIN, Round Head, 3/8 x 2-3/8 8 1724025 1 LIFT LEVER ASSY. 9 2176012 4 SAFETY CLIP 10 1722946 1 LIFT ROD 11 8031007 2 SET COLLAR 12 2171011 1 SPRING, Compression 13 1928721 2 SET SCREW, 5/16-18 x 1/2 14 1723115 1 ROD GUIDE 15 1733812 2 ROD,
ملخص المحتوى في الصفحة رقم 4
Installation Instructions Sub-Frame Hitch NOTE: Please read through these instructions and the Assemble Push Bar Latch instructions of any other attachments before beginning 1. Attach Push Bar Latch (B, Figure 3), to hitch. Secure installation. with four .31-16 x 1 bolts (A), and four .38-16 flange nuts (C). WARNING Before beginning any service work turn off the B PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). C INITIAL ASSEMBLY Assemble Hitch 1. Attac
ملخص المحتوى في الصفحة رقم 5
Sub-Frame Hitch Installation Instructions INITIAL INSTALLATION Snowthrower & Dozer Manual Lift Models E Applications LIFT LINK - EARLY VS. LATER The early model lift link (A, Figure 5) was used on early A production Conquest/1700/2700 Series tractors. It must be replaced with the later model lift link (B) included with this attachment. The later model link works in all appli- cations. Discard the early model link (A). LIFT LINK POSITION C D B The lift link is installed differently depending o
ملخص المحتوى في الصفحة رقم 6
Installation Instructions Sub-Frame Hitch A B C D E Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod 5. Push the clamp plate (D) backwards until it is snug Install Hitch against the lift shaft. Tighten the clamp plate hard- 1. Slide the hitch under the tractor. ware (E). 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. 3. Connect the front of the hitch to the tractor J-hooks (A, Figure 8) using the hitch rod (B) and a safety clip i
ملخص المحتوى في الصفحة رقم 7
Sub-Frame Hitch Installation Instructions D A B C A B C Figure 10. Install Lift Rod - All Models A. Lift Lever B. Lift Rod Figure 9. Install Lift Lever C. Clip A. Lift Lever B. Lift Shaft C. Safety Clip D. Clevis Pin Install Lift Rod 1. Slide the lift lever (A, Figure 9) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. Secure in place with a clevis pin (D) and safety clip (C). 3. Insert the rear of
ملخص المحتوى في الصفحة رقم 8
Installation Instructions Sub-Frame Hitch Snowthrower C Position D A B E F A. Hitch Rod B. Hitch Rod C. Lift Lever Extension D. Lift Link (Manual) E. Pressure Lock Plate (Hydraulic) F. Hook Figure 11. Normal Installation & Removal REMOVAL NORMAL INSTALLATION NOTE: After removing components, reinstall the clevis 1. Insert the hook (F, Figure 11) into the back of the pins and clips to prevent loss. hitch. Mount the rear of the hitch on the lift cross- shaft. 1. Disconnect the lift rod from the a
ملخص المحتوى في الصفحة رقم 9
Sub-Frame Hitch Installation Instructions Snowthrower Snowthrower & Dozer & Dozer E Applications Applications A A B F C D C D E B Mower Mower G Applications Applications A A B F D F C G E Figure 12. Lift Lock Plate - Hydraulic Lift Models Figure 13. Lift Link - Manual Lift Models A. Lift Cylinder A. Pin B. Flat Head Pin (Original) B. Rear Hole of Lift Bar (Snowthrower Applications) C. Flat Head Pin (New) C. Spacer D. Lock Plate D. Hair Pin Clip E. Hair Pin Clips E. Upper Hole (Snowthrower Appl
ملخص المحتوى في الصفحة رقم 10
Installation Instructions Sub-Frame Hitch NOTES MANUFACTURING, INC. Form No. 1733911-04 Rev. 01/2007 500 N Spring Street / PO Box 997 © 2007 Briggs & Stratton, Inc. All Rights Reserved Port Washington, WI 53074-0997 USA TP 200-4417-04-AT-SMAN
