ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
In the United States WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. WARNING: This product is a supplemental navigation tool only! The user assumes all responsibility associated with the use of this device and safe navigation. It is important to understand that all vessels may not be equipped with AIS t
ملخص المحتوى في الصفحة رقم 3
Table of Contents SECTION 1 - WHAT IS AIS? ____________________________________________________________ 4 SECTION 2 - INSTALLATION ___________________________________________________________ 6 SECTION 3 - USING THE TRANSPONDER ________________________________________________ 20 SECTION 4 - MAINTENANCE _________________________________________________________ 22 APPENDIX A - SERIAL DATA INTERFACE _________________________________________________ 22 APPENDIX B - SPE
ملخص المحتوى في الصفحة رقم 4
SECTION 1 - WHAT IS AIS? 1. Overview AIS is an acronym for Automatic Identification System. AIS increases navigational safety and collision avoidance by transmitting vessel identification, helping to reduce the difficulty of identifying ships when not in sight (e.g. at night, in radar blind arcs or shadows or at distance) by broadcasting navigational intentions to other vessels by providing ID, position, course, speed and other ship data with all other nearby ships and land based station
ملخص المحتوى في الصفحة رقم 5
On the bottom, a typical Nauticast™-B AIS installation in a common environment is shown. The Nauticast™-B AIS is connected to the vessel‟s power supply, and, in connection with the VHF and GPS antennas, the minimal requirements for transponder operation are fulfilled. Both vessels in the above illustration are equipped with an AIS transceiver. Due to “Time – Synchronization”, they use the same organization of free and allocated windows (slots) in the shared VHF Data Link (this method is
ملخص المحتوى في الصفحة رقم 6
In order to meet carriage requirements for Class A and Class B AIS systems, dedicated GPS and VHF antennas must be fit to the transponders. ACR has included GPS and VHF antennas that have been specifically designed, tested and approved for use with the Nauticast™-B. ACR Electronics Inc. does not recommend or support using other antennas or sharing data information from existing shipboard installations. Class B AIS transponders will transmit data to other AIS equipped vessels and shore ba
ملخص المحتوى في الصفحة رقم 7
2. Installation overview and prerequisites In the United States WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. The US FCC regulation states that “The entry of static data into a Class B AIS device shall be performed by the vendor of the device or by an appropriately qualified person in the business of installing marine commun
ملخص المحتوى في الصفحة رقم 8
Or, when you have downloaded an upgrade: Unzip the package when necessary and start the installer program as described in “Installation of the Link2AIS™ Software” (later in this section). If one of the following dialogs is shown when the installation process is started, the .NET® framework and/or the Windows® Installer needs to be installed. See the following sections for the installation of these required products. If neither of these dialogs is shown, the installation continues as de
ملخص المحتوى في الصفحة رقم 9
When you are not connected to the internet, an error message like the one below will be shown. From the CD If you do not want to download the .NET® framework from the Microsoft website, terminate the download process by clicking the “Cancel” button in the download dialog box and install the package directly from the CD. Locate the file “dotnetfx.exe” and double-click it to start the installation. Follow the instructions. 5. Installation of the Windows Installer Locate the fil
ملخص المحتوى في الصفحة رقم 10
When the installation process has finished, you MUST reboot your computer in order to install the Link2AIS™ Software: 6. Installation of the Link2AIS™ Software Unzip the downloaded package when necessary. Locate the files “setup.exe” and the accompanying “msi” file, then double-click on “setup.exe” The installation process of the application starts with the Welcome screen: 10 Y1-03-0222 Rev. C
ملخص المحتوى في الصفحة رقم 11
A dialog box will appear reminding you to uninstall any prior versions of the Link2AIS™ software (if applicable) before continuing the install process. Read through and accept the license agreement and click Next. 11 Y1-03-0222 Rev. C
ملخص المحتوى في الصفحة رقم 12
The next screen will allow you to pick options to be installed. These options are checked by default. Choose a directory where the software will be installed. Make note of this directory, as you will need to manually copy files to this location later on in the install process. 12 Y1-03-0222 Rev. C
ملخص المحتوى في الصفحة رقم 13
The software will ask you to choose a location in the Start menu to place the program‟s shortcuts: The next screen will ask you to confirm the install settings you have provided in the previous steps: 13 Y1-03-0222 Rev. C
ملخص المحتوى في الصفحة رقم 14
Now the application will install automatically in the folder you have chosen: The install program will tell you when installation has been completed. Click Finish. Finally, find the Coastlines folder on the installation CD and copy to the install directory chosen during the install process. If you are unable to find this directory, you can right-click the program icon on your desktop or in the Start menu, go to Properties, and look at the location shown in the “Start In” field.
ملخص المحتوى في الصفحة رقم 15
You will find the installed program shortcuts in the Start Menu / All Programs/ ACR Electronics directory (unless you chose a different location during the install process). A shortcut named “Link2AIS” will be placed on your desktop. Use either shortcut to launch the program. 7. Connecting to a personal computer (PC) NOTE: To program your Nauticast™-B AIS you will need to connect the AIS to a personal computer and supply the Nauticast™-B AIS with 12V of power. ACR recommends th
ملخص المحتوى في الصفحة رقم 16
Start up Link2AIS™ Software program on PC. The initial application screen will appear as shown: The application requires a serial connection to a Nauticast™-B AIS transponder. Connect the transponder to an available serial port. If your serial port is not located in the drop down box, select „New…‟ and create a new connection. Select the serial port from the drop down menu, then click 'Connect': Once a connection is established, the application is ready to use. Connection stat
ملخص المحتوى في الصفحة رقم 17
To configure the transponder all of the data fields must be completed and saved to the AIS. WARNING: Per FCC rules (United States users only) the static data of the vessel cannot be changed once programmed. Do not program the static data unless you are certain you have the correct information. Please check the number entered carefully. If the static data programmed is incorrect the AIS transponder will need to be returned to ACR Electronics for factory reset. Enter the vessel‟s in
ملخص المحتوى في الصفحة رقم 18
Click the 'Yes' button if the MMSI is correct. The static data tab will be updated to show the newly programmed vessel information. The MMSI number will be displayed with a grey background to indicate that it has been programmed and cannot be changed. For additional software applications unrelated to the installation, please refer to the Link2AIS™ Software user guide for technical support. 11. Hardware installation WARNING: The compass safe distance of this unit is 0.5m or
ملخص المحتوى في الصفحة رقم 19
If using PC serial terminal with third party AIS capable Electronic Charting Software, connect the user end of the data interface cable to the display device. The software in the display device must be configured for AIS operation AND to accept standard Class B AIS operation NMEA sentences. This external display unit software is not part of the Nauticast™-B AIS transponder package. By rule, Class B AIS devices must output serial data. If your computer only has a USB port, you must use a se
ملخص المحتوى في الصفحة رقم 20
The GPS antenna has a free view through 360 degrees with a vertical angle of 5 to 90 degrees above the horizon. The GNSS antenna is placed as far away as possible from radar, Inmarsat and Iridium transmitters. Also ensure that the GPS antenna is free from direct view of the radar and the Inmarsat beam. The received GPS signal is very sensitive to noise and interference generated by other onboard transmitters. The MF/HF and other VHF transmitter antennas are kept as far away as possib