ملخص المحتوى في الصفحة رقم 1
h__
SEA/RS
OWNER'S
MANUAL
Model No.
200.71460
60/20/2 AMP
MANUAL BATTERY
CHARGER
CAUTION:
250/125 AMP
Read and Follow All Safety
ENGINE STARTER with
Rules and Operating Instructions
Before Every Use of this Product.
BATTERY TESTER
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
ملخص المحتوى في الصفحة رقم 2
Table Of Contents Using Your Battery Charger .................................... 7 Warranty .................................................................. 1 Setting the controls .............................................. 7 Important Safety Instructions .................................. 2 Parts ......................................................................... 3 Charging your battery ........................................... 9 Calculating charge time ...........................
ملخص المحتوى في الصفحة رقم 3
Important Safety Instructions - SAVE THESE INSTRUCTIONS - • Read all instructions and cautions printed on the • Do not disassemble charger. Take it to a qualified battery charger, battery, and vehicle or equipment service professional if service or repair is required. using battery. Incorrect assembly may result in fire or electrical shock. • Use charger only on lead-acid type rechargeable batteries, such as those used in cars, trucks, trac- • To reduce risk of electrical shock, unplug the tors,
ملخص المحتوى في الصفحة رقم 4
Parts The exploded view of your charger shows parts, their location, and a keyed chart identifying each part by name and pert number. The wiring diagram provides additional reference for the professional repair person. Item De=mrlpUon Part Number 1 Ples_c cap Top 3799001211 2 Hub Cap 520000(x)08 3 Wheel 0099000120 4 Axle (X)99000060 5 Power Cord 90025050 6 Neg. (BLK) cable w/clamps 3899000391 7 Pos. (RED) cable w/clamps 3899000408 8 Circuit Breaker IOOA 399900066 9 Transformer 93026430 10 Diode
ملخص المحتوى في الصفحة رقم 5
Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use. Follow these instructions for easy assembly. PARTS: TOOLS NEEDED: 3/8" wrench Two 10-32 thread cutting screws (for mounting foot) 5/16" wrench Two 1/4-20 thread cutting screws (for wheels) Hammer Two wheels One
ملخص المحتوى في الصفحة رقم 6
3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided. / _lr" To attach the handle: Turn the charger right side up onto its foot and wheels. Remove the two top screws from each side of the charger and align with the screw holes on the handle, Attach the handle using the
ملخص المحتوى في الصفحة رقم 7
ATEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded. The green colored grounding clip of the adapter must be attached by a screw to a properly grounded outlet. If unsure whether outlet is properly grounded, contact a
ملخص المحتوى في الصفحة رقم 8
Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it. Follow the instructions below depending on how you choose to charge your battery. Setting the controls All the controls for your charger are located on the front of the unit. Follow these instructions to obtain the accura
ملخص المحتوى في الصفحة رقم 9
VOLTMETER: Foran accurate reading of your battery's voltage before you begin charging it, use the voltmeter as follows: 1. Set the timer to the OFF position, turn the voltage BAD f CHARGING _WEAK J SYSTEM O selector switch to 12 or 6 volt, according to the battery you are testing, and then connect the charger O GOODf GOOD as indicated in the "Charging your battery inthe f12 VOLTBATTERY vehicle" section on page 9. The charger does not have to be plugged into an outlet. 2. If a battery has recentl
ملخص المحتوى في الصفحة رقم 10
Charging Your Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads care- fully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear ofthe fan blades, belts, pulleys, and other parts that can cause injury. 3. Check the polarity ofthe battery posts using the identification marks on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -). 4. Identify which battery post is grounded or con- nected to the c
ملخص المحتوى في الصفحة رقم 11
11.When the battery isfully charged, first unplug the charger's powercord. Next, turn thetimerswitch to the OFF position. Then, standing away from the battery, remove the charger clamps in this order: (1) from the chassis connection and, (2) from the battery post. 12. Clean and store the battery charger in a dry location. Charging your battery outside the vehicle: 1. Remove the battery from vehicle, making sure to disconnect grounded terminal first with all accesso- ries and lights turned off in
ملخص المحتوى في الصفحة رقم 12
Calculating charge time The Chart Method • Marine, or deep-cycle batteries are usually rated in Use the following table to more accurately determine Reserve Capacity (RC). the time it will take to bring a battery to full charge. • NR means that the charger setting is NOT First, identify where your battery fits into the chart. RECOMMENDED. • Small batteries-- motorcycles, garden tractors, etc. Find your battery's rating on the following chart and -- are usually rated in Ampere Hours (AH). For not
ملخص المحتوى في الصفحة رقم 13
Using the engine start feature Your battery charger can be used to jump-start your 5. If the engine still does not start, charge the battery car if the battery is low. Follow these instructions on for five more minutes before cranking it again for how to use the engine start feature. five seconds. 1. Set the VOLT/AMP SELECTOR and timer switches 6. After the engine starts, unplug the charger power to the OFF position. Then follow the instructions for cord from the outlet. Then turn the VOLT/AMP h
ملخص المحتوى في الصفحة رقم 14
Troubleshooting Performance problems often result from little things that you can fix yourself. Please read through this chart for a )ossible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on the Clamps are not making a Check for poor connections to battery and frame. Make ammeter, good connection, sure connecting points are clean. 2-amp charge rate is being Ammeter may show no activity at the 2-amp charge rate. used. No reading on AC cord and/or extension Check
ملخص المحتوى في الصفحة رقم 15
60/20/2 AMP MANUAL BATTERY SEAR8 CHARGER OWNER'S 250/125 AMP MANUAL ENGINE STARTER with BATTERY TESTER Model No. 200.71460 Forinformation abouttroubleshooting Calltoll-free from anywhere inthe U.S.A. 7 amto 4:30 pmCSTMonday through Friday 1-800-SEARS-64 (1-800-732-7764) Forthe repairor replacement partsyouneed Call7 am - 7 pro,7 daysa week 1-800-366-PART (1-800-366-7278) Forthe location of a SearsRepair ServiceCenterin yourarea Call24 hours aday, 7 daysaweek 1-800-488-1222 When requesting servic
