ملخص المحتوى في الصفحة رقم 1
OWNER’S MANUAL
Model SC-6000A
For 12-Volt Batteries
Fully Automatic
Microprocessor Controlled
Battery Charger with
Engine Starter plus
Battery Tester and
Alternator Tester
CAUTION:
Read all Safety Rules and Operating Instructions,
and follow them with each use of this product.
ELECTRIC CORPORATION
Mount Prospect, IL 60056
U.S.A.
0099000366/0903
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS .................................................................... 3 PERSONAL SAFETY PRECAUTIONS ...................................................................... 4 BEFORE USING YOUR BATTERY CHARGER ......................................................... 5 PLUGGING IT IN.................................................................................................. 5 USING AN EXTENSION CORD ...............................................
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY INSTRUCTIONS WARNING – RISK OF EXPLOSIVE GASES WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BAT- TERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY. To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in vic
ملخص المحتوى في الصفحة رقم 4
Never place charger directly above Be sure to position the charger power battery being charged. The gases from cord to prevent it from being stepped the battery will corrode and damage the on, tripped over, or damaged. charger. Never pull out the plug by the cord Never touch the battery clamps together when unplugging the SpeedCharge. when the charger is on. You could Pulling on the cord may cause damage cause a spark. to the cord or the plug. Never operate charger if it has received Do not oper
ملخص المحتوى في الصفحة رقم 5
BEFORE USING YOUR BATTERY CHARGER It is important to understand the charger’s requirements. This section explains the charger’s electrical requirements and how to prepare a battery for charging. extension cord, please make sure that PLUGGING IT IN Your charger requires a 120V AC you follow these guidelines: receptacle installed according to all local Make sure that pins on plug of codes and ordinances. extension cord are the same number, size, and shape as those of plug on charger. Check tha
ملخص المحتوى في الصفحة رقم 6
OPERATING INSTRUCTIONS IMPORTANT: Follow all safety instructions and precautions when charging your battery. Wear complete eye protection and clothing protection. Charge your battery in a well-ventilated area. CHARGING BATTERY IN THE heavy, unpainted metal part of the VEHICLE: chassis or engine block, away from the battery (see figure above). DO 1. Avoid personal injury by keeping NOT connect clamp to negative clear of fan blades, belts, pulleys and battery post, carburetor, fuel line or other e
ملخص المحتوى في الصفحة رقم 7
CHARGING BATTERY REMOVED 7. To disconnect the Charger, unplug its power cord before attempting to FROM THE VEHICLE: disconnect the charger clamps. Then, POSITIVE NEGATIVE standing away from the battery, remove the output clamp from the BATTERY CHARGER NEGATIVE battery post. Finally, BATTERY remove the output clamp from the POSITIVE battery post. POWER CORD 8. Clean and store the charger in a dry 24", 6 GAUGE CABLE location. TO GROUNDED USING ENGINE START POWER OUTLET Your battery charger can be
ملخص المحتوى في الصفحة رقم 8
SPEEDCHARGE CONTROL SC-6000A CONTROL PANEL run down battery. Always use in DISPLAY MODE SWITCH combination with a battery. Use this switch to set the function of the digital LED to one of the following three. BATTERY TYPE SWITCH BATTERY %: The digital LED Use this switch button to set the type of displays an estimate of the percent of battery to be charged to one of the charge of the battery connected to following three. the SpeedCharge battery clamps. DEEP CYCLE: Deep cycle batteries VOLT
ملخص المحتوى في الصفحة رقم 9
CONTROL PANEL GUIDE 9 SC-6000A CONTROL PANEL GUIDE MODE OF OPERATION Digital Display Initial power-up, battery not detected O O O 0.0 No battery or reversed battery detected O User selected User selected User selected 0% or 0.0V Battery tester activated O User selected 0~100% Battery tester with charged battery O O User selected 100% User selected Battery tester with no battery O O 0% Voltage meter activated O User selected 0.0~17.0V User selected Alternator tester activated O 0~199% Alternator
ملخص المحتوى في الصفحة رقم 10
USING THE BUILT-IN BATTERY TESTER OVERVIEW TESTING AFTER CHARGING The SpeedCharge has a built-in battery After the unit has been changed from tester that displays either an accurate tester to charger (by selecting a charge battery voltage or an estimate of the rate), it remains a charger as long as it battery’s relative charge based on the has power. Disconnect and reconnect battery voltage and the Battery Council the power to change the unit back to a International scale. tester. TESTING SEQUEN
ملخص المحتوى في الصفحة رقم 11
USING THE BUILT-IN ALTERNATOR TESTER The SpeedCharge has a built-in on the digital LED or press the alternator tester that displays either an display mode button to set the tester accurate alternator voltage or an to “Alternator %” and read the estimate of the alternator’s relative alternator percent. output compared to normal alternators. TESTER STATUS LED’s The Alternator % values displayed When the SC-6000A is operating as an should be taken as general reference, alternator tester, the status
ملخص المحتوى في الصفحة رقم 12
while waiting and will reset if the display indicates the remaining cool engine is not cranked within 10 down time in seconds. It starts at 120 minutes. (If the charger resets, it sets and counts down to 0. The 60A itself for a 2A charge and REGULAR START LED blinks once every battery.) While waiting for cranking, second. During the cool down period, the digital display shows the battery the charger delivers charge at a rate voltage (it can’t be set to percent). of 10A and the CHARGING LED is li
ملخص المحتوى في الصفحة رقم 13
30A CHARGE RATE: When set to MAINTAIN MODE: When the 30A10A, the unit will charge the CHARGED (green) LED is lit, the battery for a few minutes at 10A. The charger has started Maintain Mode. This charger will determine whether to mode of operation is also known as increase the current to 30A, based on Float-Mode Monitoring. In this mode, factors including the battery voltage and the charger keeps the battery fully type selected. If the current is increased charged by delivering a small current
ملخص المحتوى في الصفحة رقم 14
BATTERY PERCENT AND CHARGE TIME This charger adjusts the charging time There are some important facts to keep in order to charge the battery com- in mind when charging a battery. pletely, efficiently and safely. The When the display indicates 77% microprocessor automatically makes charged, the battery has been the necessary decisions. However, this charged enough to start most vehicles section includes guidelines that can be and has already been charged as used to estimate charging times. much
ملخص المحتوى في الصفحة رقم 15
TROUBLESHOOTING Performance problems often can be corrected by the user. Please read through this chart for a possible solutions to common problems. PROBLEM POSSIBLE CAUSE SOLUTION The battery is connected The SpeedCharge is in Press the CHARGE RATE and the charger is on, tester mode, not charger button to activate charging but it isn’t charging. mode. and select a charge rate. Indicator lights are lit in an The charger may be Return to place of pur- erratic manner not defective. chase for repla
ملخص المحتوى في الصفحة رقم 16
LIMITED WARRANTY SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER DRIVE, MOUNT PROSPECT, ILLINOIS 60056-2179 MAKES THIS LIMITED WARRANTY TO THE ORIGINAL PURCHASER AT RETAIL OF THIS PRODUCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE. Schumacher Electric Corporation warrants this battery charger for five years from date of purchase at retail against defective material or workmanship. If such should occur, the unit will be repaired or replaced at the option of the manufacturer. It is the obliga
