ملخص المحتوى في الصفحة رقم 1
ST-6500 Setup Guide for Windows
TOSHIBA TEC CORPORATION
ملخص المحتوى في الصفحة رقم 2
Windows Setup Guide for ST-6500/ST-6500-C7 1 1. Introduction This setup guide describes the procedure and notes for installing the drivers on the ST-6500/ST-6500-C7. The procedure outline to set up the OS for the ST-6500/ST-6500-C7 is described below. Some drivers supported by some OS will be automatically installed, when the OS is installed. Procedure outline to set up the ST-6500/ST-6500-C7 on Windows 1) Setting up BIOS 2) Installing Windows 3) Installing the 810E2 chipset software
ملخص المحتوى في الصفحة رقم 3
Windows Setup Guide for ST-6500/ST-6500-C7 2 2. Setup on Windows 98/Windows 98SE 1) Setting up BIOS By pressing the F2 key on the keyboard, when the machine starts up, the BIOS Setup Menu is selected. Select the following item for BIOS setup. [Exit]-> Load Setup Defaults (Win98/Me) 2) Installing Windows Install Windows 98 or Windows 98SE. 3) Installing the 810E2 Chipset Software w Installing the Intel Chipset Installation Utility Execute Chipset¥Chipset¥Disk1¥Setup.exe contained i
ملخص المحتوى في الصفحة رقم 4
Windows Setup Guide for ST-6500/ST-6500-C7 3 The following screen appears. Select “Reinstall Driver” to install the driver. Select the folder to extract 100pdisk.exe to, as the folder containing the driver to be installed. ® Select “Intel PRO/100 VE Network Connection” to install the driver. For detailed installation procedure, refer to Intel’s documents and online help. TOSHIBA TEC CORPORATION
ملخص المحتوى في الصفحة رقم 5
Windows Setup Guide for ST-6500/ST-6500-C7 4 4) Installing the SM712 Graphic Driver Select [Display] on the Control Panel and display the “Display Properties” screen. On this screen, select [Settings] – [Advanced] to display the “Standard PCI Graphics Adapter Properties” screen. Select [Adapter] – [Change] on this screen. Select “Display¥SM712¥Win98” in the driver kit to install “Silicon Motion LynxEM+.” 5) Installing the CHIPS Graphic Driver Select [Display] on the Control Panel and
ملخص المحتوى في الصفحة رقم 6
Windows Setup Guide for ST-6500/ST-6500-C7 5 6) Installing the PnP Touch Panel Driver Select “SMK PnP TABLET” in the Device Manager, and click on the “Properties” button. On the “SMK PnP TABLET properties” screen, select [General] – [Reinstall Driver] to install the driver. Select “Tablet¥PnPTablet¥Win9x” in the driver kit to install “SMK PnP Tablet Driver.” Reboot the machine. Select [Touch Panel] on the Control Panel to display the “Touch Panel Property” screen. On this screen,
ملخص المحتوى في الصفحة رقم 7
Windows Setup Guide for ST-6500/ST-6500-C7 6 IMPORTANT: * Unless any of the PS/2 mouse, the serial mouse, or the USB mouse is used, the touch panel is not detected. When installing the driver, connect any of the mice and let the machine detect the touch panel. * Do not check the “Beep when touched” checkbox on the Sound tab page. This function is not available on Windows 98. (Windows 98 cannot keep the sound constant.) 7) Changing the Serial Port Setting IRQ for COM4 has been set
ملخص المحتوى في الصفحة رقم 8
Windows Setup Guide for ST-6500/ST-6500-C7 7 8) Setting up the Dual Display To enable the dual display, carry out this setup. The ST-6500-C7 enables the dual display using the Dual Display functions supported by Windows. Select [Display] on the Control Panel to display the “Display Properties” screen. On this screen, select [Settings] – [Display]. Select the on-board VGA (Intel810E2)-equipped display. Check the “Extend my Windows desktop onto this monitor” checkbox at the lower left,
ملخص المحتوى في الصفحة رقم 9
Windows Setup Guide for ST-6500/ST-6500-C7 8 IMPORTANT: * If the SM712 VGA board (SMI) has been inserted on the machine, when Windows 98 is installed, the on-board VGA (Intel810E2) cannot be used after Windows 98 has been installed. On the “Device Manager” tab of the “System Properties” screen, the on-board VGA (Intel810E2) is marked with “!”, which indicates the device is disabled. (See the screen below.) To solve this problem, remove the SM712 VGA board from the machine, then start
ملخص المحتوى في الصفحة رقم 10
Windows Setup Guide for ST-6500/ST-6500-C7 9 9) Cautions of dual-screen use by Windows98 and Windows98SE. If a dual-screen is set up by Windows 98 and Windows 98SE, an error may occur. iIn order to set up a dual-screen without generating an error, please set up the follows; Settings tab of Display Properties Control Panel. When screen is in the state of disable, as shown in a figure, it is displayed faintly. A second screen can be enabled by clicking the second display of a figure.
ملخص المحتوى في الصفحة رقم 11
Windows Setup Guide for ST-6500/ST-6500-C7 10 Apply button is clicked. Please perform PC re-starting or PC shutdown in the state having opened the control panel. Please do not click OK button or Cancel button of a display properties control panel. (If “OK” button or “Cancel” button are clicked, error may occur.) TOSHIBA TEC CORPORATION
ملخص المحتوى في الصفحة رقم 12
Windows Setup Guide for ST-6500/ST-6500-C7 11 3. Setup on Windows NT 4.0 1) Setting up BIOS By pressing the F2 key on the keyboard when the machine starts up, the BIOS Setup Menu is selected. Select the following item for BIOS setup. [Exit]-> Load Setup Defaults (DOS/WinNT/Other) 2) Installing Windows Connect the PS/2 mouse and install Windows NT 4.0. IMPORTANT: * When Windows NT is installed without connecting the PS/2 mouse, the touch panel driver cannot be installed. Be sure
ملخص المحتوى في الصفحة رقم 13
Windows Setup Guide for ST-6500/ST-6500-C7 12 Click on the “Select from list” button, and select the extracted folder to install the driver. For the detailed installation procedure, refer to Intel’s documents or online help. IMPORTANT: * If a LAN-related component is installed and the machine is rebooted after the service pack is installed, the message indicating the service is not functioning is displayed. The following event error is recorded in the event log. Even ID: 7001 S
ملخص المحتوى في الصفحة رقم 14
Windows Setup Guide for ST-6500/ST-6500-C7 13 5) Installing the SM712 Graphic Driver To use the SM712 VGA board (SMI), install this driver. Select [Display] on the Control Panel to display the “Display Properties” screen. On this screen, select [Settings] – [Display Type]. Select “Display¥SM712¥WinNT” in the driver kit, to install “Silicon Motion LynxEM+.” 6) Installing the CHIPS Graphic Driver Select [Display] on the Control Panel and display the “Display Properties” screen. On thi
ملخص المحتوى في الصفحة رقم 15
Windows Setup Guide for ST-6500/ST-6500-C7 14 7) Installing the PnP Touch Panel Driver Select [Mouse] on the Control Panel to display the “Mouse Properties” screen. Select [General] – [Change]. Select the “PnPTablet¥WinNT” fonder in the driver kit to install “SMK PnP Tablet Driver.” After rebooting the machine, select [Start] – [Run] and run “tabcalNT.exe” to set up calibration. 8) Setting up the Dual Display Since Windows NT does not support the Dual Display functions, the Dual
ملخص المحتوى في الصفحة رقم 16
Windows Setup Guide for ST-6500/ST-6500-C7 15 4. Setup on Windows 2000 1) Setting up BIOS By pressing the F2 key on the keyboard, when the machine starts up, the BIOS Setup Menu is selected. Select the following item for BIOS setup. [Exit]-> Load Setup Defaults (Win2000/XP) 2) Installing Windows Install Windows 2000. 3) Installing the 810E2 Chipset Software and the PnP Touch Panel Driver w Installing the Intel Chipset Installation Utility Execute Chipset¥Chipset¥Disk1¥Setup.exe c
ملخص المحتوى في الصفحة رقم 17
Windows Setup Guide for ST-6500/ST-6500-C7 16 On the “Found New Hardware Wizard” screen, select “Search for suitable driver for my device” and click on [Next]. Then, select “Specify a location” and designate the “Tablet¥PnPTablet¥Win2K” folder in the driver kit to install the driver. TOSHIBA TEC CORPORATION
ملخص المحتوى في الصفحة رقم 18
Windows Setup Guide for ST-6500/ST-6500-C7 17 w Installing the Intel 810/815 Chipset Family Graphics To enable the CRT display, install this driver. Execute “Chipset¥Graphics¥Win2K_XP¥Graphics¥Setup.exe” contained in the driver kit, and install the “Intel 810/815 Chipset Family Graphics Driver.” Reboot the machine. Select [Touch Panel] on the Control Panel to display the “Touch Panel Property” screen. On this screen, select [Calibration] – [Execute] to set up calibration. IMPORTANT:
ملخص المحتوى في الصفحة رقم 19
Windows Setup Guide for ST-6500/ST-6500-C7 18 5) Changing the Serial Port Setting On Windows 2000, COM4 is recognized as if there are two. Therefore, either of them must be changed from COM4 to COM5 (SIO1). IMPORTANT: * No additional operation for the SIO1 port is required, since it cannot be actually used due to hardware configuration. However, since COM4 is recognized as if there are two, either of them must be changed from COM4 to COM5 (SIO1). The port addresses and IRQs for COM
ملخص المحتوى في الصفحة رقم 20
Windows Setup Guide for ST-6500/ST-6500-C7 19 7) Setting up the Dual Display Refer to 8) Setting up the Dual Display of Section 2. Setup on Windows 98/Windows 98SE. IMPORTANT: * On Windows 2000/XP, when the mouse pointer is moved on the screen of MPEG data on the CRT monitor in the dual display, another mouse pointer may appear on the TFT monitor. To prevent this phenomenon from occurring, perform the following procedure : Display the “Display Properties” screen. Select [Settings] –
