ملخص المحتوى في الصفحة رقم 1
Title page
Expansion Module for IP Phone 1100
Series
User Guide
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Revision history Revision history May 2007 Standard 01.03. This document is up-issued to support Nortel Communication Server 1000 Release 5.0 software. December 2006 Standard 01.02. This document is up-issued to include updates based on feedback. Expansion Module for the IP Phone 1100 series terminology has been updated. December 2006 Standard 01.01. This document is up-issued to include updates based on feedback. Regulatory and safety information chapter was updated after a review. This i
ملخص المحتوى في الصفحة رقم 4
Revision history 4
ملخص المحتوى في الصفحة رقم 5
Contents Contents About the Expansion Module for IP Phone 1100 Series . . . 7 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Adjusting the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Expansion Module for IP Phone 1100 Series font support . . . . 9 Setup and assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 6
Contents 6
ملخص المحتوى في الصفحة رقم 7
About the Expansion Module for IP Phone 1100 Series About the Expansion Module for IP Phone 1100 Series This document describes the Expansion Module for IP Phone 1100 Series (Expansion Module) and how to use it with the IP Phone. Description The Expansion Module is supported on the following IP Phones: • IP Phone 1120E • IP Phone 1140E • IP Phone 1150E The Expansion Module is a hardware accessory that connects to the IP Phone and provides additional line appearances and feature keys. Up to t
ملخص المحتوى في الصفحة رقم 8
About the Expansion Module for IP Phone 1100 Series Figure 1: IP Phone 1140E with Expansion Module Features The Expansion Module has the following features: • 18 keys provide up to 36 additional self-labeled line/programmable feature keys when using the Shift feature. Using the Shift key functionality, an IP Phone 1140E, for example, can have up to 66 additional logical line/feature keys. • Upgradeable firmware using a TFTP or a UFTP Server. • A desk-mount bracket and structural baseplate su
ملخص المحتوى في الصفحة رقم 9
About the Expansion Module for IP Phone 1100 Series Adjusting the display The Expansion Module is equipped with a graphical, pixel-based, grayscale LCD display area beside the 18 line/feature keys (see Figure 1 on page 8). Each of the 18 physical keys on the Expansion Module has a 10-character display label. This label is set automatically, however, the user can edit the label using the controls on the IP Phone. To adjust the display and contrast on the Expansion Module, use the Contrast Ad
ملخص المحتوى في الصفحة رقم 10
Setup and assembly Setup and assembly The Expansion Module mounts on the right side of the IP Phone. The Expansion Module snaps into the Accessory Expansion Module (AEM) on the back of the IP Phone using the desk-mount bracket and structural baseplate supplied with the Expansion Module. 10
ملخص المحتوى في الصفحة رقم 11
Setup and assembly Installing the Expansion Module Use the following instructions to install the Expansion Module. CAUTION Damage to Equipment To avoid damaging the equipment, remove the power (PoE cable, or local power) from the IP Phone before connecting the Expansion Module. CAUTION Damage to Equipment The Expansion Module is shipped with the base locked in position. To avoid damaging the Expansion Module, press the tilt lever, located on the base at the front of the Expansion Module
ملخص المحتوى في الصفحة رقم 12
Setup and assembly Figure 2: Adjusting the stand angle on the IP Phone 2. At the back of the IP Phone, remove the rubber plug from the AEM port. Place the connecting arm of the Expansion Module behind the IP Phone and align the Expansion Module connection plug to the AEM port on the back of the IP Phone. 3. Insert the screws in to the top and bottom holes of the connecting arm of the Expansion Module and tighten until snug. See Figure 3. 12
ملخص المحتوى في الصفحة رقم 13
Setup and assembly Figure 3: Connecting the Expansion Module 4. If connecting a second, or a third Expansion Module, repeat steps 2 to 4. Note: The second Expansion Module is attached to the right side of the first Expansion Module. The third Expansion Module is attached to the right side of the second Expansion Module. 5. Adjust the height of the IP Phone tilt adjustment to a comfortable viewing angle. Then adjust each of the Expansion Module foot stands so they are flush to the desk surf
ملخص المحتوى في الصفحة رقم 14
Setup and assembly Expansion Module startup initialization Once the Expansion Module has been installed and powered up on the IP Phone, the Expansion Module initializes. Table 1 lists the initialization process for the Expansion Module. Table 1: Initializing Expansion Module Phase Description Expansion The self-test confirms the operation of the Module performs Expansion Module local memory, CPU, and other self-test circuitry. While undergoing this self-test, the Expansion Module display lig
ملخص المحتوى في الصفحة رقم 15
Setup and assembly Adjusting the tilt base The Expansion Module stand provides a continuous tilt adjustment so the tilt angle matches the IP Phone stand angle while accommodating variations in the desk surface. A clamp mechanism is used to unlock and lock the foot stand angle. CAUTION Do not over tighten the wheel on the Expansion Module. The Expansion Module is tightened by spinning the wheel clockwise and loosened by spinning the wheel counter-clockwise. Turn the wheel on the back right si
ملخص المحتوى في الصفحة رقم 16
Controls and settings Controls and settings When an Expansion Module is installed on an IP Phone, the controls and settings of the IP Phone control both the IP Phone and the Expansion Module. Use the Telephone Options menu on the attached IP Phone to set the contrast and feature key labels of the Expansion Module. For more information about controls and settings (including the Telephone Options menu) for your IP Phone, see the IP Phone user guide. Shift key functionality The IP Phone 1140E
ملخص المحتوى في الصفحة رقم 17
Controls and settings Press the Services key to access the following menu items: • Display diagnostics • Set Info Display diagnostics Use the Up/Down navigation keys to scroll the Display diagnostics menu to access the following screens/diagnostic operations: • initial screen • Full Contrast •LED Test • Character Test Initial screen Instructions are displayed on the display area of the IP Phone and the Expansion Module. The DN/feature key display areas is blank. Full Contrast The IP Phone and
ملخص المحتوى في الصفحة رقم 18
Controls and settings Table 2 shows the display diagnostic operation on the IP Phones and the Expansion Module. Table 2: Display diagnostic operation on the IP Phone and the Expansion Module Expansion Module for IP Phone DN/feature Diagnostic step IP Phone 1100 Series key display area area display initial screen blank blank Full Contrast set to highest contrast set to highest contrast LED Test blank blank Character Test Characters display Characters display across the display across the di
ملخص المحتوى في الصفحة رقم 19
Regulatory and safety information Regulatory and safety information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
ملخص المحتوى في الصفحة رقم 20
Regulatory and safety information この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすこと があります。 取扱説明書に従って正しい取り扱いをして下さい。 Table 3 lists EMC compliance for various jurisdictions. Table 3: EMC compliance Jurisdiction Standard Description United States FCC CFR 47 Class B Emissions: FCC Rules for Radio Part 15 Frequency Devices Canada ICES-003 Class B Emissions: Interference-Causing Equipment Standard: Digital Apparatus Aust
