ملخص المحتوى في الصفحة رقم 1
Voice / Fax over IP Networks
Configuration Guide for
Voice/IP Gateways
Bogen PCM Zone Paging
MultiVOIP Models: MVP130-BG, MVP210-BG,
MVP410-BG, MVP810-BG
ملخص المحتوى في الصفحة رقم 2
Configuration Guide Doc # Bogen03 MultiVOIP Models MVP130-BG, MVP210-BG, MVP410-BG, MVP810-BG This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2004, by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpos
ملخص المحتوى في الصفحة رقم 3
Bogen paging example using FXS Pass Through feature. The example below shows a Bogen PCM/ZPM Zone Paging unit at the Corporate site connected through MultiVOIPs to amplifiers and speakers at each of two branch sites. Users at the corporate site can page users at the Branch A and/or Branch B sites. The FXS Pass Through feature allows an “always on” audio connection to exist between the Corporate site and both Branch A and Branch B sites. The MultiVOIPs use of Silence Compression means little or n
ملخص المحتوى في الصفحة رقم 4
1. Preliminary planning: Determine the number of MultiVOIP gateways to be used for the paging network. Assign a unique IP address and identifying number to each MultiVOIP. It is helpful to write this down like below: MultiVOIP Identifying IP Address Local Voice Destination Destination Name Number Channel MultiVOIP MultiVOIP Voice Number Channel Corporate 1 192.168.25.20 1 2 1 23 1 Branch A 2 192.168.25.21 1 1 1 Branch B 3 192.168.25.22 1 1 2 2. In the Configuration / IP screen of the MultiVOIP C
ملخص المحتوى في الصفحة رقم 5
Branch A Branch B 5
ملخص المحتوى في الصفحة رقم 6
3. In the Configuration/Interface screen, Select each voice channel used for paging from the Select Channel drop-down list and configure that channel so FXS Loop Start and Pass Through are enabled. Click Ok when finished. 6
ملخص المحتوى في الصفحة رقم 7
4. Go to the Phone Book / Phone Book Modify / Outbound Phone Book / List Entries screen. 7
ملخص المحتوى في الصفحة رقم 8
5. Click the Add button to add a phone book entry. In the Destination Pattern field, enter the identifying number for one of the remote MultiVOIP units. Enter the IP address of the remote MultiVOIP unit in the IP Address field. Leave the other fields set at their defaults. 8
ملخص المحتوى في الصفحة رقم 9
6. Click Ok when finished with this entry. Click the Add button as needed to create enties for other remote MultiVOIP units. In our example, the Corporate MultiVOIP would have two entries like below: The Branch A and Branch B MultiVOIP entries would look like this: 9
ملخص المحتوى في الصفحة رقم 10
7. In the configuration / Voice/Fax screen, select one of the channels to be used for paging and click the Auto Call Enable checkbox to enable the auto call feature. In the Phone Number field, enter x:y where x equals the remote MultiVOIP identifying number and y equals the remote MultiVOIP Voice Channel number. For example, on Corporate MultiVOIP channel 1 you would enter 2:1 to communicate with Branch A voice channel 1. For best voice quality, configure the Voice Coder field to G.711 U-Law @ 6
ملخص المحتوى في الصفحة رقم 11
Corporate Channel 2 Branch A Channel 1 11
ملخص المحتوى في الصفحة رقم 12
Branch B Channel 1 8. Select Save Setup / Save and Reboot to save the configuration to the MultiVOIP. 9. Assuming a Bogen PCMZPM is located at Corporate, connect a RJ11 phone cord to channel 1 FXS/FXO jack on the Corporate MultiVOIP. Connect the two wires on the other end of the phone cord to the Zone A + and – leads on the PCMZPM. Connect another RJ11 phone cord between channel 2 FXS/FXO jack and the Zone B + and – leads on the PCMZPM. A cord with an RJ11 plug on one end and tinned leads on the
