ملخص المحتوى في الصفحة رقم 1
®
Broadband PowerShield
Models: CP16 and CP27
User Manual
990-2366A 04/2006
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Chapter 1: General Information ® The PowerShield provides a power source for broadband telephony, Fiber-to-the-Home/Premise (FTTH/P), and other direct current (DC) equipment/applications. Safety This manual contains important instructions that should be followed during installation and maintenance of the APC equipment and batteries. It is intended for APC customers that set up, install, relocate, or maintain APC equipment. Changes and modifications to this unit not expressly appro
ملخص المحتوى في الصفحة رقم 4
Specifications General Model Number Input Output Maximum Maximum Battery Signal Signal Type Voltage Current CP16U48 100-240 V 50/60 Hz 1.0 A 48 V 30 V 5 mA 12 V 7.2 AHr 16 W Spill-Proof, Maintenance- 13 V CP27U13 100-240 V 50/60 Hz 1.0 A 30 V 5 mA Free, 27 W Sealed Lead Acid Environmental Operating Temperature -4º F to 122º F (-20º C to 50º C) Operating Humidity 5 to 95% noncondensing within enclosure Maximum Operating Elevation 10,000 ft (3,000 m) Maximum Storage Elevat
ملخص المحتوى في الصفحة رقم 5
Chapter 2: Installation Enclosure Installation Install the enclosure in a protected area that is free of excessive dust and has adequate airflow. Do not operate the PowerShield where the temperature and humidity are outside the specified limits. See Indoor Use Only Specifications. ! " # Battery Cover Release Tabs $ Use screws that are appropriate for the weight of this unit and the mounting surface material. See Specifications. 3
ملخص المحتوى في الصفحة رقم 6
Battery Installation ! " # Red Black Cable Cable Positive Negative Terminal Terminal Battery Cover Release Tabs $ % 4
ملخص المحتوى في الصفحة رقم 7
Connect Equipment and Power The PowerShield battery charges when it is connected to utility power. The battery charges fully during the first eight hours of normal operation. Do not expect full battery run capability during this initial charge period. Utility Power Cord Inlet Output Power and Optional Runtime Communication Extension Connector Signals 1. Connect the PowerShield to the application equipment (example: FTTH/P Optical
ملخص المحتوى في الصفحة رقم 8
Chapter 3: Operation Status Indicators and Features Front Panel Status Indicators Indicator Description Utility Solid green indicates the unit is on utility power. Solid yellow indicates that utility power is not present and the unit is on battery power. Flashing green LED indicates the unit is fast-charging. Green indicates the unit is working properly and DC output power is provided Output by the battery or the utility power. Replace Battery/ Red indicates that the ba
ملخص المحتوى في الصفحة رقم 9
Alarm Silence Button The audible alarms may be silenced by utilizing the dual function Replace Battery/Alarm Silence LED/button / . Function Button Operation Description (Press and hold for:) Replace Battery- <4 seconds If the alarm has been silenced, the unit will emit one quick beep. If the alarm has been Temporarily enabled, two quick beeps will be emitted. Enable/Disable Replace Battery- 8-12 seconds If the alarm has been silenced, the unit will emit one quick beep. If the
ملخص المحتوى في الصفحة رقم 10
Chapter 4: Maintenance, Service, Approvals, and Warranty Battery Replacement This unit has an easy to replace, hot-swappable battery. Replacement is a safe procedure, isolated from electrical hazards. You may leave the unit and connected equipment on for this procedure. During the self-test, battery removal and replacement are not recommended. For self-test disabling, see Alarm Silence Button. Replace the spent battery with APC replacement battery RBC2. See your dealer or refer to t
ملخص المحتوى في الصفحة رقم 11
4. Return the unit by insured, prepaid carrier to the address given to you by Customer Support. Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulations. Contact Information Refer to the APC Web site, www.apc.com. Regulatory Approvals 9
ملخص المحتوى في الصفحة رقم 12
Limited Warranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from customer support. Products must be returned with transportation charges prepaid and mus
