Sanus Systems PFPL دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

 
 








 



 
 

+ 

(  
 

 


  
 (


  

 (  

 

  !!"#$%&$$'!

ملخص المحتوى في الصفحة رقم 2

ملخص المحتوى في الصفحة رقم 3

CAUTION There are many small components used in theconstructionofthis unit. These loose items should be kept away fromyoungchildrenwhile assembling your unit. Shelf Pin Barrel nut P840048 x 8 P860121 x 1 P860035 x 6 P840050 x 8 Wooden dowel Connector rod Cam P860015x 8 P800201 x 8 P820016Tx 8 P820015Tx 8 P816145x 4 Cable Ducts P840170 x 2

ملخص المحتوى في الصفحة رقم 4

Insert wooden dowels into sides as shown. x8 1. Fasten 8 Connector Rods into small holes in Top as shown.

ملخص المحتوى في الصفحة رقم 5

Intersecting hole Important: *When fitting the rails onto the top, ensure that the grooved part of the rails are closest to the side edges of the top. * The larger holes (cam holes) in the rails must always be closest to the Top. 1.Insert black BarrelNuts intosmaller holes in Rails,ensuringslot in capisaligned to intersectinghole. 2.Insert silver Cams into larger holes in Rails, ensuring that arrow on Cam points towards intersecting hole. 3. Press fit Rails to Top as shown.

ملخص المحتوى في الصفحة رقم 6

ملخص المحتوى في الصفحة رقم 7

ملخص المحتوى في الصفحة رقم 8

ملخص المحتوى في الصفحة رقم 9

ملخص المحتوى في الصفحة رقم 10

ملخص المحتوى في الصفحة رقم 11

ملخص المحتوى في الصفحة رقم 12

Locking screw x8 Base 1. With assistance align Base onto Dowels in Sides & Rails & then press fit. 2. Fasten large Locking screws through Base into Sides &Rails ( Screw heads should be flush with surface).

ملخص المحتوى في الصفحة رقم 13

Following steps apply to both flat and curved front designs. Glide x6 Screwx6 1. Fasten the glides to the base as shown.

ملخص المحتوى في الصفحة رقم 14

Adjusting screw x4 1. Turn unit over carefully. 2. Screweach Adjusting screwinto Side by half of it's visible threaded length, thenoncethis is done, tighten all4 Adjusting screws fully into Side.

ملخص المحتوى في الصفحة رقم 15

Flat edgeof the glass Curved edge of the glass shelves must be placed at shelves must be placed at front frontforthe flat frontdesign. for curved front design. Glass shelf Glass shelf Shelf Pin x8 1. Insert Shelf Pins into holes at the lower positions of boththe Sides (as illustrated above). 2. Tilt and slide Glass Shelf between Rails (ensuring frosted side down) and place ontop of Shelf Pins. 3. Insert Shelf Pins into holes at the upper positions of oneSideonly. 4. Tilt and slide the second Gla

ملخص المحتوى في الصفحة رقم 16

1. Press fit 2 Cable Ducts into large holes in theBase. 2. You have now completed the assembly of your new Digital TV stand. NOTE: We recommend that all contents stored in or on this item of furniture be removed before shiftingit.The manufacturers will not be held liable for damage caused when furniture is shifted without first removingitscontents. If furniture is shifted we recommend that it is lifted not dragged.