ملخص المحتوى في الصفحة رقم 1
INSTALLATION INSTRUCTIONS
SCM-103
Suspended Ceiling Mount
AUSTRALIA, NEW ZEALAND,
EUROPE
NORTH AMERICA OCEANIA (DISTRIBUTOR)
3130 East Miraloma Avenue
Swallow House,
P.O. Box 295
Anaheim, CA 92806 USA
Shilton Industrial Estate,
Mordialloc Victoria 3195
USA and Canada –
Shilton, Coventry, England CV79JY
Australia
Phone: 800-368-9700
Phone: +44 (0) 2476 614700
Phone: 039586 6330
Fax: 800-832-4888
Fax: +44 (0) 2476 614710
www.premiermounts.com.au
Other Locations – Phone: (001)-714-632-7100; Fax:
ملخص المحتوى في الصفحة رقم 2
SCM-103 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Locating the Mounting Points 4 Mounting the Brackets to the Display 5 Securing the Lower Cover 6 Securing the Tubes to the Mounting Brackets 6 Lifting the Display into Position 8 Cable Routing 9 Installing the Beauty Covers 12 Technical Specifications 14 Warranty 15 Warning Statements IT IS REQUIRED THAT THE INSTALLATIO
ملخص المحتوى في الصفحة رقم 3
SCM-103 Parts List This ceiling mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are missing and/or damaged parts, please stop the installation and contact Premier Mounts (800-368-9700). Mounting Brackets Mounting Bracket Covers Tubing Lower Cover (Qty 2) (Qty 2) (Qty 3) (Qty 1) Display Input Cover 8-32 x 1/2” Phillips Screws Lower Cover Panel Plastic Coupler Inserts
ملخص المحتوى في الصفحة رقم 4
SCM-103 Locate the Mounting Points The display comes with four (4) M16 screws with quick release sleeves that are pre-installed on the display. Mounting Mounting Points Points Step 1. Locate the 4 quick release sleeves on the back of the display and remove. Place the M16 bolts and split washers to the side. These will be used for bracket installation on the next page. Page 4 Installation Instructions
ملخص المحتوى في الصفحة رقم 5
SCM-103 Mounting the Brackets to the Display The following steps will require a minimum of 3 people. This should not be done with less then 3 people due to the weight of mounting brackets. Left Mounting Bracket Right Mounting Bracket Split Washer M16 Bolt Step 1. Align the mounting bracket holes up with the mounting holes on the back of the display. There are two mounting holes used on each side of the display. Step 2. Place the split washer between the display and the m
ملخص المحتوى في الصفحة رقم 6
SCM-103 Securing the Lower Cover THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL INSTALLATION STEPS. 8-32 x ½” Screw 10-32 Kep Nut Lower Cover Pre Installed Handy Box Step 1. Insert the lower cover between the vertical mounting brackets. Step 2. Attach four (4) 10-32 Kep Nuts and tighten down securing the lower cover into place. Step 3. Insert two (2) 8-32 x ½” screws and tighten down the lower cover bracket against the vertical side mounting brackets. Securi
ملخص المحتوى في الصفحة رقم 7
SCM-103 THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL INSTALLATION STEPS. Clevis Pin 2” Tube Cotter Pin Step 5. Once the tubes are locked into place insert the clevis pins into the hole at the end of each tube. Step 6. Lock each clevis pin into place by inserting the attached cotter pin into the hole. Now that the mount is attached to the display, double check all mounting locations to insure all hardware is properly tightened and secured. Installation Ins
ملخص المحتوى في الصفحة رقم 8
SCM-103 Lifting the Display into Position IN THE NEXT STEP A LIFTING DEVICE SUCH AS A FORKLIFT , SCISSOR LIFT, OR HOIST WILL NEED TO BE UTILIZED IN ORDER TO LIFT DISPLAY INTO POSITION. NOT DOING SO COULD RESULT IN PERSON- AL INJURY OR DAMAGE TO THE DISPLAY. THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL INSTALLATION STEPS. The display may be hung from a ceiling structure using two (2) main support cables and two (2) safety cables. Length, mounting location an
ملخص المحتوى في الصفحة رقم 9
SCM-103 Cable Routing Pre-Hung Cable 2 Hole Locations for Cable Routing Step 1. Route the pre-hung cables through the top of the left and right mounting brackets attached to the display. Two holes are provided at the top of each mounting bracket. Cables can be routed so both are going through one hole or routed so each cable runs through its own hole. The system is designed to allow for 2 cables on each mounting bracket. 1 cable for support & 1 as a safety redundancy cable. Step 2. Locate
ملخص المحتوى في الصفحة رقم 10
SCM-103 THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL INSTALLATION STEPS. Step 3. Slide plastic insert plug down cabling and insert into the top of the mounting bracket. A cut out in the mounting bracket is provided that will allow the plastic cap to sit flush with the top of the mounting bracket Step 4. Locate the 6-32 x 1/4” Set Screw and insert into the sides of the plastic top locking the plastic plug into position. The set screw location is on
ملخص المحتوى في الصفحة رقم 11
SCM-103 THE SCM-103 IS HEAVY. IT IS STRONGLY RECOMMENDED THAT THREE PEOPLE PERFORM ALL INSTALLATION STEPS. Step 6. Locate the ½”-20 Nuts & ½” flat washer. Step 7. Measure 1 ¾” inches up the threaded stud attached to the cable and thread one ½-20 nut into position. Leveling adjustment can be made at this stage by setting the nut position at different heights on the threaded post attached to the cable. Step 8. Slide one ½” flat washer up to the nut and insert the end of the stud into the bot
ملخص المحتوى في الصفحة رقم 12
SCM-103 Installing the Beauty Covers 8/32 x 3/8” Screw Step 1. After all cables have been routed through mount and are properly installed, locate the display input cover panel. Step 2. Install the panel by sliding it into position behind the tubes. Step 3. Lock the cover into position by tightening the six (6) 8-3 x 3/8” screws. Mounting Bracket Cover Step 4. Slide the mounting bracket covers into position. Page 12 Installation Instructions
ملخص المحتوى في الصفحة رقم 13
SCM-103 8-32 x 3/8” Screws Step 5. Once cover is slid into position tighten down using the 8-32 x 3/8” screws. Lower Cover Step 6. Drop the lower cover into position between the 2 display mounting brackets and lock into place using the 8-32 x 3/8” screws provided. Step 7. Make sure that the display is level and slowly lower your support equipment. Installation Instructions Page 13
ملخص المحتوى في الصفحة رقم 14
SCM-103 Technical Specifications All measurements are in inches(mm). Page 14 Installation Instructions
ملخص المحتوى في الصفحة رقم 15
SCM-103 Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
