ملخص المحتوى في الصفحة رقم 1
Water Rainbow™ Fill Spout/Faucet Kit
Installation Instructions
IMPORTANT: Read all instructions before beginning installation. Consult local codes for requirements.
The Water Rainbow fi ll spout/faucet kit is designed
WATER RAINBOW FILL SPOUT
for installation on most Jacuzzi Whirlpool Bath
AND FAUCET HANDLES
products or on any bath having suffi cient rim space
for mounting. The installation procedure requires
drilling holes in the bath shell, mounting fi ttings,
and making the proper water s
ملخص المحتوى في الصفحة رقم 2
Using a scribe tool or awl, mark the center points FILL SPOUT BODY for all holes, then remove the template. Drill holes from the fi nished surface side of the unit carefully, being sure they are the proper size. We recommend that you drill pilot holes and then use the recommended drill size. For best results, begin drilling at slow speed, then use high speed. PIPE Appropriate sizes of hole saws will be needed for EXTENSION this. SILICONE Clean up dust particles using a soft cloth damp-
ملخص المحتوى في الصفحة رقم 3
SCREW #10-24 X3/8" PHPM (2) SUGGESTED WATER RAINBOW INSERT PLUMBING SCHEME A - FOR FAUCET HANDLE WATER RAINBOW SEPARATED VALVE (HOT) FILL SPOUT CONFIGURATIONS (Pipe and fittings not provided.) GASKET FAUCET HANDLE (2) INSERT FAUCET HANDLE LOCKNUT VALVE (2) (COLD) 1/4-20 (2) WASHER FAUCET HANDLE (2) 1/4" FLAT (2) FAUCET WRENCH 5/8" X 1/2" ELL BOLT 1/4-20 X 1-1/2" HOT WATER HEX HEAD SUPPLY 5/8" O.D. COPPER PIPE TEE 5/8" X 5/8" X 1/2" SPEEDNUT PUSH-ON 1-1/2" (2) 5/8" O.D. COPPER PIPE 5/8" X 1/2"
ملخص المحتوى في الصفحة رقم 4
Installing the Faucet Handles Install the rubber gasket into the faucet handle INSERT aligning the fl at of the gasket with the projection from the handle, then aligning the fl at surface on the SCREW stem with the fl at inside handle, place the handle onto the stem of the faucet valve. FAUCET Insert the #10-24 x 3/8" L stainless steel PHPM HANDLE screw (provided) through the handle and gasket into the valve stem and tighten. Rotate handles clockwise to the end of travel. RUBBER Push in in
ملخص المحتوى في الصفحة رقم 5
Installation for Top Access OPTIONAL SHOWER HEAD If service access to Water Rainbow plumbing (NOT SUPPLIED) under the rim is not possible, it is possible to install ANTI-SIPHON VALVE SHOULD the spout so that it can be replaced at a later date BE A MINIMUM OF 6" ABOVE (if necessary) from the top of the rim. To do this, RIM OF BATH allow at least 2" of fl exibility in the piping so it can ANTI-SIPHON VALVE be pulled up through the rim. Use a compression & TRANSFER VALVE (NOT SUPPLIED) fi t
ملخص المحتوى في الصفحة رقم 6
CAUTION Since plumbing fi ttings may contribute detectable amounts of lead to water, the following notice is required by California law (Proposition 65). "This product contains a chemical known to the State of California to cause birth defects or reproductive harm." In normal use, any lead exposure can be minimized by allowing the water to run free for several seconds before drinking. Proper installation of the fi ll spout and compliance with local codes is the responsibility of the installer.
ملخص المحتوى في الصفحة رقم 7
HOLE DRILLING TEMPLATE—WATER RAINBOW™ CHECK TEMPLATE SCALE USING REFERENCE DIMENSIONS BEFORE DRILLING If scale is off, do not continue, call customer support at 1-800-288-4002 to obtain a new template BATH RIM HOLE FOR THREADED PIPE EXTENSION 9/32" DIA. (FILL SPOUT) 1-3/8" DIA. (2-1/2" REF) (1/2" REF) 9/32" DIA. C L 15/64" PILOT (2-1/2" REF) HOLE DRILL PILOT HOLE FIRST INTERIOR OF BATH HOT WATER COLD WATER FAUCET HOLE FAUCET HOLE (3" REF) 1-1/2" DIA. 1-1/2" DIA. 15/64" 15/64" RIB HOLE RIB HOLE
ملخص المحتوى في الصفحة رقم 8
© Copyright 1991 Jacuzzi Whirlpool Bath 6683000G 8/06
