Crimestopper Security Products SV-6400 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

SV-6400 ClipCam


SAFETY PRECAUTIONS

z Make sure to read the “Installation Manual” for safety precautions before
installing unit or accessories.
z Please make sure the vehicle is well parked in a safe place. Make sure that the
engine and the power are switched off.
z Avoid installation outdoors during rain or thunder storms.
z The instructions presented in this manual are based on the passenger seat at the
right of the driver’s seat. In an opposite situation, change the

ملخص المحتوى في الصفحة رقم 2

PACKAGE CONTENTS Check your package for the listed contents. If you do not find all of the listed items, contact the supplier from whom you purchased the camera before installing the unit and accessories. (1) Clip Cam (1) Camera Clip (small) (1) Camera Clip (large) (2) Screws (1) 20’ cable (10) Cable Carpet Clips ? INSTALLATION Before installing the unit and accessories, read this manual in its entirety. The ClipCam is designed to work on most vehicles. Ho

ملخص المحتوى في الصفحة رقم 3

Step 1: Testing the Camera (Bench Testing) 1. Prepare two sets of DC 11-13V batteries for running a bench test to make sure the camera functions are working properly (before you actually install the camera into your vehicle). 2. Refer to the wiring diagram (4.1-3) the camera and the monitor each have to have their own power source, DO NOT connect with the same battery. 3. When connecting the 20’ cable, make sure all connectors have been solidly connected. 4. Turn on the monitor an

ملخص المحتوى في الصفحة رقم 4

2. When making your selection, choose the tighter fit of the 2 camera clips that are included. 3. Insert the camera clip into the camera housing. 4. If for any reason you need to change the camera clip size, please open the pre-cut window at the back side of the camera. Next, use a flat screw driver to lift up the camera clip enough to remove it from the camera housing. Change to the correct camera clip and reinsert into the camera housing. (Refer to the diagrams

ملخص المحتوى في الصفحة رقم 5

6. Optional installation: Sometimes the space between vehicle license plate and rear trunk lip area is very narrow, which may cause problems when installing the ClipCam. An adjustable bracket is available to deal with this problem. Install the adjustable bracket to move up the license plate until you have enough space to install the ClipCam. Step 4: Wire Connection 1. Connect the power source line to the camera. Also connect a 20’ cable with monitor. (Refer to Diagram 4.1

ملخص المحتوى في الصفحة رقم 6

Diagram 4.1-3 2. In most cases and as a time saver, connect the camera power at the rear of vehicle behind the reverse lights. The red power wire line goes to the reverse light + 12 V and the black wire to ground. 3. Please carefully choose a hidden location to run the camera. Drilling a cable hole if necessary. 4. Please make sure to use the rubber grommet or plug to make a watertight seal for the cable where it passes into the vehicle body. 5. Please refer to the monitor wirin

ملخص المحتوى في الصفحة رقم 7

Technical Specification The following table defines the technical specifications for the SV-6400 ClipCam. Page 7 of 8

ملخص المحتوى في الصفحة رقم 8

1770 SOUTH TAPO STREET ª SIMI VALLEY, CALIFORNIA 93063 800-998-6880 ª 805-526-9400 ª FAX 805-581-9500 WWW.CRIMESTOPPER.COM © 2005 CrimeStopper Security Products, Inc. Page 8 of 8