Crestron electronic Crestron iLux CLS-C6 series دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

CLS-EXP-DIMU
CLS-EXP-DIMU Physical View
Functional Summary
The CLS-EXP-DIMU enables the expansion of the
Crestron iLux™ Integrated Lighting System (CLS-C6
series) and other Crestron lighting dimmers to allow
dimming of both forward and reverse phase type loads.
Supported loads include electronic low-voltage, magnetic
low-voltage, incandescent, neon/cold cathode, or 2-wire
dimmable fluorescent. A single model supports 120, 230,
or 277 Volt loads up to 16 Amps.
The CLS-EXP-DIMU simplif

ملخص المحتوى في الصفحة رقم 2

iLux™ Expansion Module Crestron CLS-EXP-DIMU CLS-EXP-DIMU Specifications (continued) CLS-EXP-DIMU Specifications (continued) SPECIFICATION DETAILS SPECIFICATION DETAILS Enclosure Surface mount module with (2) Dimensions integral mounting flanges, Height 8.82 in (22.40 cm) galvanized steel w/gray matte Width 6.39 in (16.23 cm) powder coat front panel, Depth 3.18 in (8.08 cm) extruded aluminum heat sink, ½” Weight 3.34 lbs (1.52 kg) and ¾” conduit knockouts Compatible Control

ملخص المحتوى في الصفحة رقم 3

Crestron CLS-EXP-DIMU iLux™ Expansion Module Application The following diagram shows several CLS-EXP-DIMU modules in a typical application. CLS-EXP-DIMU Modules in a Lighting Application Installation Guide – DOC. 6682B iLux Expansion Module: CLS-EXP-DIMU • 3

ملخص المحتوى في الصفحة رقم 4

iLux™ Expansion Module Crestron CLS-EXP-DIMU Connectors, Controls & Indicators # CONNECTORS, DESCRIPTION Physical Description CONTROLS & INDICATORS This section provides information on the connections, 1 FLUORESCENT (1) Recessed screwdriver- controls and indicators available on the CLS-EXP-DIMU. OFF THRESHOLD adjustable trim pot, adjusts minimum brightness level. CLS-EXP-DIMU Overall Dimensions Covered by removable cap. 5.79 in 3.18 in (14.71 cm) (8.08 cm) 2 PHASE LED (1) Yellow LED

ملخص المحتوى في الصفحة رقم 5

Crestron CLS-EXP-DIMU iLux™ Expansion Module Hardware Hookup Setup WARNING: RISK OF SERIOUS PERSONAL INJURY. Turn off power at the circuit breaker(s) prior to installation. Installing with power on can result in serious Important Notes personal injury and damage to the device. Read before installation. • Permits: An electrical permit shall be obtained 1. Use a #2 Philips screwdriver to remove the cover prior to each installation. screws as shown in the following diagram and remove t

ملخص المحتوى في الصفحة رقم 6

   iLux™ Expansion Module Crestron CLS-EXP-DIMU CLS-EXP-DIMU Wiring with Dual Feeds The dimming mode can be changed by adjusting the S1 HOT DIP switches as detailed in the following table. (120 to 277 VAC) CLS-EXP-DIMU NEUTRAL NEUTRAL Switch Settings for S1 DIP Switch DIM OUT Lighting LOAD 3 SW. 1 SW. 2 DIMMING MODE LOAD TYPES Loads LOAD 2 HOT LOAD 1 CLS(I)-C6 (120 (230) VAC) Off Off Auto Detect All HOT NEUTRAL (Default, recommended) NEUTRAL On Off Reverse Phase Incandescent, El

ملخص المحتوى في الصفحة رقم 7

Crestron CLS-EXP-DIMU iLux™ Expansion Module CLS-EXP-DIMU Troubleshooting (continued) 2. Using a flat-head screwdriver, turn the FLUORESCENT OFF THRESHOLD TROUBLE POSSIBLE CORRECTIVE adjustment counter-clockwise until it stops. CAUSE(S) ACTION Audible noise Load is being Refer to the list of 3. Set the CLS-C6 so that the light output is on but is while dimming. dimmed in wrong load types in the below the desired minimum level. mode. table at the top of page 6. Check the 4. Turn the

ملخص المحتوى في الصفحة رقم 8

iLux™ Expansion Module Crestron CLS-EXP-DIMU Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and ph