Fisher-Price P6033 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

P6033
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fi sher-price.co.uk

ملخص المحتوى في الصفحة رقم 2

Consumer Information Care The pad and is machine washable. Wash the pad separately in cold water on the gentle cycle. Do not use bleach. Tumble dry WARNING separately on low heat and remove promptly. The frame can be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse this product. To prevent serious injury from To remove the pad: falls and being strangled in the • Lift the footrest and remove the pad lower pocket. restraint system: • Push the restraint belts ba

ملخص المحتوى في الصفحة رقم 3

Parts Assembly IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use CAUTION if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. This package contains small parts in its unassembled state. Adult assembly Front Leg Back Leg is required. IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packe

ملخص المحتوى في الصفحة رقم 4

Assembly PULL UP PULL UP Base Tube 3 Base Tube 5 • While standing on the base tube, pull the front legs up. The front legs should remain secured to the base tube. If you can remove the front legs, you have not assembled them correctly to the base • While standing on the base tube, pull the back legs up. The back tube. Re-read and repeat assembly step 2. legs should remain secured to the base tube. If you can remove the back legs, you have not assembled them correctly to the base tube. Re-re

ملخص المحتوى في الصفحة رقم 5

Assembly Seat Hub S Slots lots Waist Belt Seat Hub 7 • Insert a screw through the outside of each seat hub and into each frame arm. Tighten the screws. Fasteners 9 • From behind the assembly, insert the waist belts through the slots in the pad. • Press to fasten the waist belt assembly to the pad. Pad Upper Pocket Pad Lower Pocket Seat Bottom Tube Seat Back Tube 10 Waist Belts 8 • Fit the pad lower pocket onto the seat bottom tube, as shown. • Fit the pad upper pocket over the seat back tub

ملخص المحتوى في الصفحة رقم 6

Battery Installation Battery Safety Information In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: Battery Compartment Door • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long periods of non-use. Always remove exhausted batte

ملخص المحتوى في الصفحة رقم 7

Securing Your Child Restraint System WARNING To prevent serious injury from falls and being strangled in the restraint system: • Always use the restraint system. • Not recommended for children who can sit up by themselves (6 months approximately, until 9 kg/20 lbs). • Never leave child unattended. • It is dangerous to use this product 2 on an elevated surface. • Tighten each waist belt so that the restraint system is snug against your child. Please refer to the next section for

ملخص المحتوى في الصفحة رقم 8

Starting the Swing Storage IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. Power Switch • Lift the seat bottom. • Slide the power switch to any of five speed settings. • Give the seat a light push to start the swinging motion. Adjust the power switch to the desired swing motion setting. Hin