American Standard Tropic 7038.801 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installation
Instructions
7038.801
TROPIC
Spread Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Certified to comply with ANSI A112.18.1
M968892 Rev. 1.1
Speed Connect™ Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Sp

ملخص المحتوى في الصفحة رقم 2

POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE Fig. A. Fig. B. 3 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT 4 RE

ملخص المحتوى في الصفحة رقم 3

ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

ملخص المحتوى في الصفحة رقم 4

INSTALL HANDLES 10 Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. Fig. A. Tighten THREAD ON STEM SCREW (3) to secure ADAPTER (1). TO DECK 4 ADAPTER Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting TOP male teeth on ADAPTER (1) to female teeth in HANDLE (4). Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) 1 until snug against mounting surface. 3 Fig. A. 2 SPLINE END DOWN 5 TEST INSTALLED FITTING 11 1 With HANDLES (1) i

ملخص المحتوى في الصفحة رقم 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

ملخص المحتوى في الصفحة رقم 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s