American Standard Hampton 7411.722 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installation
Instructions
7411.702
7411.712
Centerset Lavatory Faucet with
7411.722
EverClean™ Finish & SpeedConnect™ Drain
7411.732
Congratulations on purchasing your American Standard faucet with
EverClean finish and SpeedConnect drain, two features found only
on American Standard faucets.
Certified to comply with ANSI A112.18.1
EverClean Finish SpeedConnect Drain*
US60402 Rev.1.1
• One wipe effortlessly removes spots  Fewer parts, installs in less time
 Eliminates the need for cleaners

ملخص المحتوى في الصفحة رقم 2

POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). 3 BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE 3 Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT 4 BE

ملخص المحتوى في الصفحة رقم 3

ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and 1 closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

ملخص المحتوى في الصفحة رقم 4

TEST INSTALLED FITTING 10 With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). 4 1 Operate both HANDLES (1) to flush water lines thoroughly. 1 Replace AERATOR (3). CHECK DRAIN CONNECTIONS 3 Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions. Release P

ملخص المحتوى في الصفحة رقم 5

SpeedConnect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position:  Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly:  Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper:  Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain:  Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. CAB

ملخص المحتوى في الصفحة رقم 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s