ملخص المحتوى في الصفحة رقم 1
Gryphon™ I GM4100
General Purpose Handheld
Linear Imager Barcode Reader
Quick Reference Guide
ملخص المحتوى في الصفحة رقم 2
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the con- tents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclu- siv
ملخص المحتوى في الصفحة رقم 3
Table of Contents Statement of Agency Compliance .......................................................... 1 FCC Class B Compliance Statement ............................................. 1 FCC RF Radiation Exposure Statement ............................ 1 Canadian Notice .................................................................................. 2 Software Product Policy .............................................................................. 6 Customers Under Software Support ...
ملخص المحتوى في الصفحة رقم 4
NOTES
ملخص المحتوى في الصفحة رقم 5
Gryphon™ I GM4100 Quick Reference Guide Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any in- terference received, including interference that may cause unde- sired operation. FCC Class B Compliance Statement The user is cautioned that changes or modifications not expressly approved by the part responsible for compliance
ملخص المحتوى في الصفحة رقم 6
Statement of Agency Compliance Canadian Notice This equipment does not exceed the Class B limits for radio noise emissions as described in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n’emet pas de bruits radioelec- triques depassant les limites applicables aux appareils numeriques de la classe B prescrites dans le Reglement sur le brouillage radio- electrique edicte par le ministere des Communications du Cana- da. Do not attem
ملخص المحتوى في الصفحة رقم 7
Statement of Agency Compliance Datalogic Scanning, Inc. GRYPHON™ PRODUCT SERIES END USER LICENSE AGREEMENT Notice to End User: The Datalogic Product you have acquired contains embed- ded Software, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement. If you do not intend to be bound
ملخص المحتوى في الصفحة رقم 8
Statement of Agency Compliance logic may elect not to terminate this Agreement or the granted licenses, but instead may elect to notify End User that End User is deemed to have ordered and accepted a license for each breaching use. End User shall pay Datalogic the applicable list price for such licenses as of the date of such breach. 3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or other- wise transfer the Datalogic Product to any third party unless such third pa
ملخص المحتوى في الصفحة رقم 9
Statement of Agency Compliance provided, that 1) End User notifies Datalogic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent to Datalogic Scanning, Inc., Legal Department, 959 Terry Street, Eugene, OR 97402. 7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the right to continue
ملخص المحتوى في الصفحة رقم 10
Software Product Policy writing, and shall be effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Contract Administration, Data- logic Scanning, Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be specified by Datalogic in writing. 11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agree- ment shall not prevent the party's later enforcement of such terms and condi- tions. 11.4 Governing Law
ملخص المحتوى في الصفحة رقم 11
Setting Up the Reader Setting Up the Reader Follow the steps below to connect and get your reader up and communicating with its host. 1. Install the Batteries 2. Connecting the Base Station 3. Select the Interface Type 4. Configure Other Settings (if not using factory settings for that interface) Battery Safety To install, charge and/or do any other action on the battery, fol- low the instructions in this manual. Before installing the Battery, read “Battery Safety” on the following pages. Da
ملخص المحتوى في الصفحة رقم 12
Setting Up the Reader Do not discharge the battery using any device except for the scanner. When the battery is used in devices other than the designated product, it may damage the battery or reduce its life expectancy. If the device WARNING causes an abnormal current to flow, it may cause the battery to become hot, explode or ignite and cause serious injury. Lithium-ion battery packs may get hot, explode or ignite and cause serious injury if exposed to abusive conditions. Be sure to follow the
ملخص المحتوى في الصفحة رقم 13
Setting Up the Reader Always charge the battery at 32° – 104°F (0° - 40°C) tem- perature range. Use only the authorized power supplies, battery pack, chargers, and docks supplied by your Datalogic reseller. CAUTION The use of any other power supplies can damage the device and void your warranty. Do not disassemble or modify the battery. The battery contains safety and protection devices, which, if dam- aged, may cause the battery to generate heat, explode or ignite. Do not place the battery in
ملخص المحتوى في الصفحة رقم 14
Setting Up the Reader Install the Batteries Before installing the Battery, read “Battery Safety” on the preceding pages. Datalogic recommends annual replacement of rechargeable battery packs to ensure maximum performance. NOTE To install or change the battery of your reader, you must: 1. With a screwdriver, unscrew the battery cover screw. 2. Unplug the three screws securing the battery holder, and unplug the white connector. Screw Connector Screw Screw 10 Gryphon™ I GM4100
ملخص المحتوى في الصفحة رقم 15
Setting Up the Reader 3. Carefully lift out the gold contacts circuit, and remove the battery holder while letting the white connector pass through the hole in the battery holder (as shown in the picture below). Pass-through hole 4. Remove the old battery from its place (if present), and insert the new battery in the same position. 5. Replace the battery holder, plug in the connector and return the contacts circuit to its previous location. When inserting the new battery into the handle,
ملخص المحتوى في الصفحة رقم 16
Configuring the Base Station Configuring the Base Station The base charger/station may be configured in desk application to hold the reader in two different positions, either a horizontal or standing position, in order to provide the most comfortable use depending on needs. Horizontal Standing Changing the Base Station Position The base station is configured by installing one of two sets of me- chanical parts that come with the cordless kit. The default mounts (shown below) provide three o
ملخص المحتوى في الصفحة رقم 17
Configuring the Base Station 2. Using your thumbs, push open the plastic tabs on the bottom of the base to free the wing holders. Tab Tab 3. The stand can now be repositioned in either horizontal or standing position. Horizontal Standing Quick Reference Guide 13
ملخص المحتوى في الصفحة رقم 18
Configuring the Base Station Connecting the Base Station Figure 1 shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before connection and con- sult the manual for that equipment (if necessary) before proceed- ing. Connect the interface cable before applying power to the Base Station. Gryphon Mobile can also be Powered by the Terminal. The external power supply is recommended but not necessary. When powered by the Terminal, the battery charger is a
ملخص المحتوى في الصفحة رقم 19
Configuring the Base Station Figure 2. Options for routing the DC cord Please refer to the arrows depicted on the bottom of the base when placing the cables, detailed in Figure 3. Figure 3. Arrows showing routing Host Connection: Verify before connection that the reader’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 4 on page 16. Keyboard Wedge interface cables have a ‘Y’ connection where its female end mates with
ملخص المحتوى في الصفحة رقم 20
K e W y e b d o a g r d e Configuring the Base Station Figure 4. Connecting to the Host or... or... or... Power Connection : Plug the AC Adapter in to an approved AC wall socket with the cable facing downwards (as shown in Figure 1) to prevent undue strain on the socket. Gryphon Mobile can also be Powered by the Terminal. The external power supply is recommended but not necessary. When powered by the Terminal, the battery charger is auto- matically set as Slow charge. NOTE Disconnecting t
