ملخص المحتوى في الصفحة رقم 1
Cordless Impact
Wrench
MODEL 6934FD
004367
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ملخص المحتوى في الصفحة رقم 2
SPECIFICATIONS Model 6934FD Standard bolt M8 - M16 (5/16” - 5/8”) Capacities High tensile bolt M6 - M12 (1/4” - 1/2”) Square drive 12.7mm (1/2”) No load speed (RPM) 0 - 2,300/min. Impacts per minute 0 - 3,000 Max. fastening torque 140 N.m (103 ft.lbs) Overall length 173 mm (6-13/16”) Net weight 1.7 kg (3.7 lbs) Battery Battery Cartridge Voltage Input Output Charging time Charger 1422 45 min. A. C. only D. C. 1434 14.4 V DC1414 60 min. 50 Hz - 60 Hz 7.2 V - 14.4 V 1435 70 min. • Manufacturer re
ملخص المحتوى في الصفحة رقم 3
SAVE THESE INSTRUCTIONS 9. Remove adjusting keys or wrenches Work Area before turning the tool on. A wrench or a 1. Keep your work area clean and well lit. key that is left attached to a rotating part of Cluttered benches and dark areas invite acci- the tool may result in personal injury. dents. 10. Do not overreach. Keep proper footing 2. Do not operate power tools in explosive and balance at all times. Proper footing and atmospheres, such as in the presence of balance enable better control of
ملخص المحتوى في الصفحة رقم 4
18. Maintain tools with care. Keep cutting one tool may create a risk of injury when tools sharp and clean. Properly maintained used on another tool. tools with sharp cutting edge are less likely to Service bind and are easier to control. 21. Tool service must be performed only by 19. Check for misalignment or binding of qualified repair personnel. Service or main- moving parts, breakage of parts, and any tenance performed by unqualified personnel other condition that may affect the tool’s may r
ملخص المحتوى في الصفحة رقم 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD302-1 The followings show the symbols used for tool. V ....................... volts .../min................revolutions or reciprocation per minute ................... direct current ................number of blow ................... no load speed n ˚ IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE USC001-3 1. SAVE THESE INS
ملخص المحتوى في الصفحة رقم 6
c. That wire size is at least as large as the one specified in the table below. Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS Length of Cord (Feet) 25 50 100 150 AWG Size of Cord 18 18 18 16 9. Do not operate charger with damaged 13. The battery charger is not intended for cord or plug - replace them immediately. use by young children or infirm persons without supervision. 10. Do not operate charger if it has received a sharp blow, been dropped, or otherwise 14.
ملخص المحتوى في الصفحة رقم 7
7. Do not incinerate the Battery Cartridge 8. Be careful not to drop, shake or strike bat- even if it is severely damaged or is com- tery. pletely worn out. The battery cartridge can 9. Do not charge inside a box or container of explode in a fire. any kind. The battery must be placed in a well ventilated area during charging. SAVE THESE INSTRUCTIONS 7
ملخص المحتوى في الصفحة رقم 8
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 004341 Installing or removing battery cartridge 1 • Always switch off the tool before insertion or removal of the battery cartridge. • To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. 2 • To insert the battery cartridge, align the tongue on the battery cartridge
ملخص المحتوى في الصفحة رقم 9
NOTE: • The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer’s batteries. • When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. • If you charge a battery cartridge fro
ملخص المحتوى في الصفحة رقم 10
004369 Switch action CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. 1 To start the tool, simply pull the switch trigger. Tool speed is 1. Switch trigger increased by increasing pressure on the switch trigger. Release the switch trigger to stop. Electric brake This tool is equipped with an electric brake. If the tool consis- tently fails to quickly stop after switch tri
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Selecting correct socket Always use the correct size socket for bolts and nuts. An incorrect size socket will result in inaccurate and inconsistent fastening torque and/or damage to the bolt or nut. 004371 Installing or removing socket 1 Align the hole in the side of the socket with the detent pin on the anvil and push it onto the anvil of the tool until
ملخص المحتوى في الصفحة رقم 12
OPERATION 004373 The proper fastening torque may differ depending upon the Standard bolt kind or size of the bolt, the material of the workpiece to be . M16 N m 140 . (1428) (kgf cm) fastened, etc. The relation between fastening torque and fas- 120 (1224) tening time is shown in the figures. M16 100 (1020) Hold the tool firmly and place the socket over the bolt or nut. M14 80 Turn the tool on and fasten for the proper fastening time. (816) M12 M14 60 NOTE: (612) M10 M12 • When fastening sc
ملخص المحتوى في الصفحة رقم 13
4. The use of the universal joint or the extension bar some- what reduces the fastening force of the impact wrench. Compensate by fastening for a longer period of time. 5. The manner of holding the tool or the material of driving position to be fastened will affect the torque. 6. Operating the tool at low speed will cause a reduction in the fastening torque. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspe
ملخص المحتوى في الصفحة رقم 14
2. a) Take the battery to your nearest Makita Factory Ser- vice Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been desig- nated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under “Tools-Electric”. ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool
ملخص المحتوى في الصفحة رقم 15
Memo 15
ملخص المحتوى في الصفحة رقم 16
Memo 16
ملخص المحتوى في الصفحة رقم 17
Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 17 Cut
ملخص المحتوى في الصفحة رقم 18
Your answers to the following questions are appreciated. 1. This product was purchased from? 3. How did you first learn of Makita Power Tools? Hardware/lumber Store Industrial Supply Magazine/Newspaper Catalog Tool Distributor Other ( ) From dealer Other ( ) Store display 2. Use of the product is intended for? 4. Most favored points are? Construction trade Home maintenance Design Makita Brand Industrial maintenance Other ( ) Features Power Size
ملخص المحتوى في الصفحة رقم 19
Factory Service Centres Head Office: 1950 Forbes St., Whitby, Ontario, L1N 7B7 (905) 571 - 2200 1-800-263-3734 Regional Office: 11771 Hammersmith Way, Richmond B.C. V7A 5H6 (604) 272 - 3104 1-800-663-0909 Regional Office: 6389 boul. Couture, St. Leonard, Quebec (Montreal) H1P 3J5 (514) 323 - 1223 1-800-361-7049 Dartmouth: 202 Brownlow Avenue Dartmouth, N.S., B3B 1T5 (902) 468 - 7064 1-888-625-4821 Ville St. Laurent: 1140 Rue Bégin, Ville St. Laurent, Quebec (Montreal) H4R 1X1 (514) 745 -
ملخص المحتوى في الصفحة رقم 20
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centres. If inspection shows the trouble is caused by defective workmanship or material, M
