ملخص المحتوى في الصفحة رقم 1
®
Digita DigitallDXR DXR
DigitalDXR
Wireless Audio/Video
Monitoring System
compatible with...
Compatible
with…
70204
ملخص المحتوى في الصفحة رقم 2
monitoring made easy
ملخص المحتوى في الصفحة رقم 3
monitoring made easy
ملخص المحتوى في الصفحة رقم 4
TABLE OF CONTENTS Introduction 1 Package Contents 2 About 2.4 GHz Wireless Technology 3 Consumer Guide to Product Safety 4-5 Knowing your Receiver 6 Knowing Your Camera 7 Installation & Setup 8 Monitor Operation 9-13 Recording Function 14 Audio/Video & USB Operation 15 Troubleshooting 16 Radio Interference Advice 17 Warranty 18 Notes 19
ملخص المحتوى في الصفحة رقم 5
INTRODUCTION Congratulations on the purchase of the MobiCam® Digital DXR Monitoring System, which brings you the latest in wireless technology. We are sure that you will be pleased with the quality and features of this product but recommend that you read these instructions carefully before use in order to fully benefit from its many features. The MobiCam® Digital DXR enables you to transmit picture and sound wireless- ly, which is ideal for many situations such as monitoring a baby, young ch
ملخص المحتوى في الصفحة رقم 6
PACKAGE CONTENTS ABOUT DIGITAL WIRELESS TECHNOLOGY 1 x Monitor Unit (Receiver) plus built-in rechargeable battery 1 x Camera Unit (Additional Cameras - #70205, battery sold separately) 1 x Montor Power Cord 1 x Camera Power Cord 1 x USB Cable 1 x Camera Mount 1 x Set of mounting screws and anchors NOTE: If you find any of the contents are missing or should you need to order replacement parts, please contact the manufacturer or visit www.getmobi.com. 2
ملخص المحتوى في الصفحة رقم 7
ABOUT DIGITAL WIRELESS TECHNOLOGY About 2.4 GHz Digital Wireless Signal This innovative digital wireless solution integrates advance Frequency Hop- ping Spread Spectrum (FHSS) technology. This technology greatly reduces the interference that comes from other devises using the same radio frequency (2.4 GHz), e.g. WIFI, Bluetooth, cordless phones, etc. However, a weaker signal (lag or still image) can occur from time to time depending on the environment where the system is installed. Factors
ملخص المحتوى في الصفحة رقم 8
CONSUMER GUIDE TO PRODUCT SAFETY CONSUMER GUIDE TO PRODUCT SAFETY Please read this instruction manual before using your MobiCam® Digital DXR System. When using electrical appliances, basic safety precautions should al- ways be followed. Also please keep this manual for future reference. • This product is not intended to be used as a medical monitor and its use should not replace adult supervision. • Periodically examine this product for damage to the cord, housing or other parts t
ملخص المحتوى في الصفحة رقم 9
CONSUMER GUIDE TO PRODUCT SAFETY • Always use transmitter and receiver where there is adequate ventilation. To prevent overheating, keep away from heat sources such as radiators, heat registers, stoves, or other appliances that produce heat. • Use only a dry or very lightly dampened cotton cloth to keep the Camera and Monitor units free of dust. Do no use a fully moisened cloth, water, or liquid cleaner of any kind. • Unplug the AC adaptors from the Monitor and Camera du
ملخص المحتوى في الصفحة رقم 10
KNOWING YOUR MONITOR KNOWING YOUR CAMERA 1. Battery Indicator Green LED = Battery is charging Red LED = Battery is low LED OFF = Battery is fully charged 2. Power On Indicator 3. Cursor Up / Channel Switch / Quad Mode button 4. Cursor Left / Volume Down button 5. Cursor Down / Audio Only button 6. Cursor Right / Volume Up button 7. Menu / Esc button 8. Record / Delete button 9. Two-Way Audio Button / OK (confirm) button (press and hold button to engage two-way mode) 10. Power
ملخص المحتوى في الصفحة رقم 11
KNOWING YOUR CAMERA 1. Lens 2. Infrared LEDs 3. EDS 4. Battery Indicator (battery sold separately) 5. Link Indicator Blinking LED = LED will blink indicating camera is ready to be paired Blue LED = Camera is paired to the receiver LED OFF = Camera is on standby mode 6. Power On Indicator 7. Microphone 8. Power Switch 9. Pairing Button 10. Reset button (inset) 11. DC Jack 7
ملخص المحتوى في الصفحة رقم 12
INSTALLATION & SETUP Camera Start-Up 1. Connect power cable to Camera’s DC IN jack, then plug its power supply adapter into wall outlet. 2. Slide [Power Button] once to turn ON the camera. NOTE: Use only the 5V/1A power adaptor provided in the package. To operate without power cable visit www.getmobi.com to purchase the optional recharge- able battery. Monitor Start-Up 1. Connect power cable to Monitor’s DC IN jack, then plug its power supply adapter into wall outlet. 2. Press [Power Bu
ملخص المحتوى في الصفحة رقم 13
MONITOR OPERATION Time Setting To set the time and date on your monitor, press the Menu button (no. 7, pg. 6), use the Cursor buttons to go to System Setup and press the OK button to enter the Time Setting, use the Cursor buttons to change the setting and press OK again to save. Power Saving By setting the Power Saving mode on your monitor, you can conserve battery power. The monitor will turn Off after 2 minutes of it being idle. To set this mode press the Menu button (no. 7, pg. 6), use the
ملخص المحتوى في الصفحة رقم 14
MONITOR OPERATION MONITOR OPERATION SD Card Format To format an SD memory card press the Menu button (no. 7, pg.6) go to SD Card, press OK and use the Cursor buttons to select No or Yes. Your MobiCam® DXR is formatted to be used with 2GB to 16GB SD memory cards (not included with the system). NOTE: Its strongly recommended that your SD card be formatted before use. Pairing Camera To pair additonal cameras press the Menu button (no. 7, pg. 6) go to Pairing press OK (no. 9, pg. 6) use the Cu
ملخص المحتوى في الصفحة رقم 15
MONITOR OPERATION Brightness To adjust the brightness on your display press the Menu button (no. 7, pg. 6), use up/down Curser buttons to go to Brightness and press OK (no. 9, pg.6). Use the left and right Cursor buttons to adjust. Once the brightness has been adjusted press the Menu button again to exit this setting. Alarm The monitor has 3 convenient alarm settings that will warn you if your camera battery (sold separately) is low, you are out of range, or if VOX mode is engaged. Press th
ملخص المحتوى في الصفحة رقم 16
MONITOR OPERATION VOX Sensitivity During Voice Activation (VOX) your monitor will go on standby mode and stop transmit- ting picture and sound. Once the camera senses sound the monitor will automatically turn on and begin producing picture and sound. You can activate VOX by pressing the Menu button (no. 7, pg. 6), going to VOX Setting, and selecting the Sensitivity Level. It is recommended you select level 2 or 3 as level 1 is highly sensitive. You must have power-saving mode ON during VOX m
ملخص المحتوى في الصفحة رقم 17
MONITOR OPERATION Camera ON/OFF Once you have paired extra cameras to your monitor, you can turn off any camera you do not wish to scan. Press the Menu button (no.7, pg. 6), go to Camera Setup, and use the Cursor buttons to select a camera you wish to turn off and press OK. Factory Default To reset your monitor to factory settings press the Menu button (no.7, pg. 6), go to System Setup and select No or Yes. 13
ملخص المحتوى في الصفحة رقم 18
RECORDING FUNCTION You can record live video directly within your monitor by inserting an SD card into the SD card slot (no. 11, pg. 6). You can begin recording manually or by setting up VOX to begin recordings through sound activation. To record manually simply press the Record button (no. 8, pg. 6). A recording icon will appear on the screen. To stop the recording press the Record button again. VOX Recordings To set the monitor to record when the camera senses sound, press the Menu button
ملخص المحتوى في الصفحة رقم 19
USB OPERATION USB Output Your monitor is equipped with a USB output so you can connect your monitor to your computer allowing you to capture video and sound from the camera transmission. NOTE: The monitor screen turns off automatically when USB cable is used. The screen will turn back on when the cable is removed. USB Connection NOTE: You will need to install a USB devise driver before using the USB connec- tion to your PC. Visit our website at www.getmobi.com and go to our support page to
ملخص المحتوى في الصفحة رقم 20
TROUBLESHOOTING Problem Solution System shows “ No Signal” • Check the power cord connection and the battery power. • Pair your camera • Place the camera close to the moni- tor • If possible remove major obstacles between camera and monitor. Low or unstable signal • Adjust camera and monitor position • Keep WIFI router away from camera or monitor • Keep working motors (hair dryer, air conditioner, water pump) or micro- wave away from the camera and/or monitor. Recording does not work
