Yamaha NS-C125 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

English Français Deutsch Español
URG
Owner’s Manual
NS-P125
HOME CINEMA CENTER & EFFECT SPEAKERS
NS-C125/NS-M125
SPEAKER SYSTEM
Thank you for choosing a Yamaha speaker system.
• NS-P125 are speaker sets consisting of the
• Center speaker NS-C125 x 1
components shown on the table. NS-P125  Effect (Surround) NS-M125 x 2
speakers
 The NS-C125 spekaer is designed for use as the center speaker in a surround sound system.
 NS-M125 speakers are designed for use as front or surround speakers in a su

ملخص المحتوى في الصفحة رقم 2

Supplied Accessories Setting Up the Speakers  NS-M125 Place the speakers on a sturdy, vibration-free surface, such as a well-built stand. Speaker cable (10 m): 1 pc./unit ■ Using the NS-M125 as Normal Stereo Speakers To get the best stereo performance, angle the speakers inward so as to create a triangle, with the listener at the apex.  NS-C125 Speaker cable (4 m) Fasteners x 2 ■ Using the NS-M125 as Front Speakers in a Surround Sound System Position the speakers both side of your TV. T

ملخص المحتوى في الصفحة رقم 3

English 60 mm (2-3/8”) ■ Using the NS-M125 as surround Fasten screws into a firm wall or wall support as shown in the figure below, and hang the holes on speakers in a surround sound the protruding screws. system NS-M125 The speakers can be mounted on a wall by using Diam. 3.5 to the bracket attached to the speakers’ back panels. 4 mm (1/8”) Min. 20 mm (3/4”) 3 mm (1/8”) Tapping screw (commercially available) Holes Wall or wall support WARNING: • Each speaker weights 2 kg (4.4 lbs). Do

ملخص المحتوى في الصفحة رقم 4

■ Placing the center speaker ■ Mounting the center speaker NS-C125 NS-C125 on the wall Place the speaker on the floor under the TV or The speaker can be mounted on a wall by using inside the TV rack so that it is stabilized. the bracket attached to the speaker’s back panel. Holes Make sure that the screws are caught by a narrow part of the holes securely. When placing the speaker on top of the TV To prevent the speaker from falling down, put the 292 mm (11-1/2”) provided fasteners at two poin

ملخص المحتوى في الصفحة رقم 5

English Connecting Your Speakers Always turn off your amplifier or receiver before making any connections. ■ Preparing Your Speaker Cables Carefully remove 10 mm (3/8 ”)of insulation from both ends of your 10 mm (3/8 ”) speaker cables and twist the bare wires tightly, as shown. Good No Good ■ Hookup NS-C125 FRONT CENTER OR R SURROUND L Amplifier or receiver + – Tighten + Loosen – NS-M125 Notes:  Make sure that the bare wires are not touching each other as this could damage the speaker and a

ملخص المحتوى في الصفحة رقم 6

Specifications NS-M125 NS-C125 Type................. 2-way bass reflex speaker system Type.................2-way bass reflex speaker system magnetic shielding type magnetic shielding type Driver ...................8 cm (3-1/8”) cone woofer x 2 Driver ...................8 cm (3-1/8”) cone woofer x 2 2.2 cm (7/8”) balanced dome tweeter 2.2 cm (7/8”) balanced dome tweeter Impedance...................................................... 6 Ω Impedance ................................................