Draper SL دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Installation/Operating Instructions
SL & SLX Scissor Lift Video Projector Lift by Draper
must be allowed below projector or optional ceiling closure: 4' for Model
Caution:
SL4, 5' for Model SL5, etc.; 11' for Model SLX11, 12' for Model SLX12, etc.
➀ Read instructions completely before proceeding.
➅ Do not use unit to support adjacent ceiling, light fi xtures, etc.
➁ Test lift prior to installation.
➆ Do not complete the ceiling below unit until electrical connections have
➂ Follow instruction

ملخص المحتوى في الصفحة رقم 2

Scissor Lift by Draper page 2 of 6 Installing Optional Plenum Housing Installing Projector The Plenum Housing is shipped in pieces, and must be assembled by the Depending on job conditions and projector, it may be easier to re move installer. The height of the plenum can be adjusted by up to 2" (5 cm) by moving optional ceiling closure panel before installing projector. the trim frame to different mounting holes in side panels. It is recommended that Generally, the video pro jec tor shoul

ملخص المحتوى في الصفحة رقم 3

Scissor Lift by Draper page 3 of 6 Installing Optional Ceiling Closure Panel— Size "B" or "E" If your Scissor Lift is equipped with a "B" or "E" ceiling closure panel, it can be used as is, or in conjunction with a piece of existing ceiling tile. ➀ If installing with ceiling tile, you may need to cut tile so overall dimensions are the same as (or slightly less than) the closure panel. Place tile into trim frame. Lay closure panel on top (back side) of tile & tighten screws to hold in place

ملخص المحتوى في الصفحة رقم 4

29½" 26¾" Scissor Lift by Draper page 4 of 6 23½" 23" SL Series 20¾" 20¾" Scissor Lift Dimensions Maximum Lowering Retracted 9 /16" dia. 1 Model Distance Height mounting holes 1 SL4 4' 8 /8" 1 See chart SL5 5' 9 /8" (shown slightly 1 lowered) SL6 6' 10 /8" 1 SL7 7' 11 /8" 1 SL8 8' 12 /8" Space for Fail-safe inertial projector's safety belt system 1 SL9 9' 13 /8" ceiling Space for projector mounting 1 1 SL10 10' 14 /8" Pair of /8" aircraft cables bracket SLX11 11' 13¾" Optional

ملخص المحتوى في الصفحة رقم 5

10A Scissor Lift by Draper page 5 of 6 www.draperinc.com (765) 987-7999 L1 N GRD 110v AC Supply Dashed wiring by Transformer BK electrician BK YW GN YW BK WH WH BEBK Capacitor 6 12 34 5 7 8 910 YW 3 x 3 Up Relay Down Relay Connection BE BE NC BE NC Board GN NO NO BK RD BE Motor BE RD COM RD COM BK RD RD RD (-) (+) (-) (+) 12 34 5 6 7 8 910 BK RD BE BE RD BK BK BK BK BK RD BK BK BK GN 6 Conductor Modular Cable (75' supplied) YW BE RDRD RD BK BE BK BK RD Down Wall Switch Key Up BE BE Limit switch

ملخص المحتوى في الصفحة رقم 6

Scissor Lift by Draper page 6 of 6 Adjusting Show Position (Up to Standard Position) ➀ Find the empty slot in the bottom of the top pan of lift (the only empty slot). ➁ Use the open-end wrench (provided) Front of Unit ➂ Find the threaded coupling (long nut) just inside the top pan (through the slot). ➃ Push wrench toward rear of unit to lower. ➄ Pull wrench toward front of unit to raise. Increase Show Position Decrease Show Position (Stops Lower) (Stops Higher) Front Rear Show Position Adjustm