ملخص المحتوى في الصفحة رقم 1
D9112B
Program Entry Guide
EN Control Panel
ملخص المحتوى في الصفحة رقم 2
D9112B | Program Entry Guide | EN | 2 Notice The material and instructions covered in this manual Generally words shown in all capital letters indicate were carefully checked for accuracy and presumed to command center displays, and command center keys. be reliable. However, Bosch Security Systems assumes For example, SERVC COMM FAIL is the command no responsibility for inaccuracies and reserves the right center display for failure to communicate with the to modify and revise this m
ملخص المحتوى في الصفحة رقم 3
D9112B | Program Entry Guide | Contents EN | 3 1.5 RAM Parameters............................................22 RAM Passcode ............................................................ 22 Table of Contents Log % Full .................................................................... 22 1.0 Panel Wide Parameter..................................8 RAM Call Back ........................................................... 23 1.1 Phone.......................................................
ملخص المحتوى في الصفحة رقم 4
D9112B | Program Entry Guide | Contents EN | 4 W## Open Early Begin.............................................36 Perim Delay................................................................. 51 W## Open Window Start ........................................36 L## Perim Delay ......................................................... 52 2.4.1 Programming Two Opening Windows Watch Mode ................................................................ 53 on the Same Day .......................
ملخص المحتوى في الصفحة رقم 5
D9112B | Program Entry Guide | Contents EN | 5 L## Remote Program..................................................59 UW## Holiday 4 ........................................................ 65 Move to Area...............................................................59 6.0 Passcode Worksheet....................................66 L## Move to Area........................................................59 Duress ........................................................................... 66
ملخص المحتوى في الصفحة رقم 6
D9112B | Program Entry Guide | Contents EN | 6 Point Index...................................................................80 S## Friday ................................................................... 93 BFSK Code...................................................................80 S## Saturday............................................................... 93 Point Text .....................................................................81 S## Xept Holiday ...........................
ملخص المحتوى في الصفحة رقم 7
D9112B | Program Entry Guide | Contents EN | 7 Table of Tables Table 1: Modem II Communication Format Data – User ID Numbers (Point/User Flag)..............10 Table 2: Modem II Communication Format Data – Point Numbers (Point/User Flag)...................10 Table 3: Phone Routing ...............................................13 Table 4: Phone Routing Worksheet – Fire Alarm/Res (Fire Alarm/Restoral)....................................13 Table 5: Phone Routing Worksheet – Fire Tbl/Re
ملخص المحتوى في الصفحة رقم 8
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 8 A Comm Restoral event generates after another reporting event successfully transmits to any of the 1.0 Panel Wide Parameter receiver phone numbers. This Comm Restoral report Use this programming module to define the operating is sent according to the routing for Power/Phone in characteristics that affect panel-wide functions. This Phone Routing. When you receive a Comm Restoral module has five categories: report, use RAM
ملخص المحتوى في الصفحة رقم 9
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 9 Default: Blank Selection: Up to 24 characters (do not enter [SPACE]) 0 - 9 Numbers zero through nine C 3 sec. pause D 7 sec. dial-tone detect. The same as pressing this key on a telephone keypad when manually dialing. For example, you may need an asterisk (*) to access your long distance service. Do not use these characters when pulse # or * dialing. Panel dials no phone number. Programming this item Blank does not
ملخص المحتوى في الصفحة رقم 10
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 10 Point/User Flag When Modem Format is YES, the D9112 sends This program item determines how point and User expanded Modem II reports to the receiver. ID numbers are presented at the D6500 display, Point/User Flag affects Modem II data as shown in printer, and computer RS-232 output. the following table. The leading zero in the User ID Number with Point/User Flag programmed NO is When Modem Format is YES, the D9112 sends
ملخص المحتوى في الصفحة رقم 11
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 11 User ID 5 = ZONE F Phone line trouble responses: User ID 6 = ZONE 6 Command centers display SERVC PH LINE # and sound the trouble tone. User ID 7 = ZONE 7 Restoral reports identify the previously failed line User ID 8 = ZONE 8 after it restores when a single phone line is used, if User ID 91 = ZONE 1 Power/Phone is enabled in Phone Routing. User ID 92 = ZONE 2 Trouble and restoral events are reported if User ID 93 =
ملخص المحتوى في الصفحة رقم 12
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 12 Ground Start BFSK Duress Code Use only when the panel is connected to Ground Start telephone lines. Default: 0 Some newer ground start telephone exchange Selection: 0 to 9 switches require a shorter amount of time to initiate When transmitting in BFSK (Modem Format is a dial tone. If the panel cannot initiate a dial tone on programmed NO), you must assign a number to the ground start line with the default (Long) sett
ملخص المحتوى في الصفحة رقم 13
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 13 Table 3: Phone Routing Report Group Description Blank Not reported to this phone number. P Primary: Send all reports from this group to this phone number. Only one primary phone allowed per group. B Backup: Send reports from this group to this phone if the report is not received by the primary phone number. A primary phone route must also be programmed for this Report Group in order to dial the backup phone number. Onl
ملخص المحتوى في الصفحة رقم 14
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 14 Table 6: Phone Routing Worksheet – Alarm/ Res/Cncl (Non-Fire Alarm/Restoral/ Cancel) Report Type Phone 1 Phone 2 Phone 3 Phone 4 x x Alarm Report x x User Alarm CMD 9 x x Restoral Report x x Duress x x User Code Tamper x x Missing Alarm User Alarm CMD 7 Cancel Alarm Table 7: Phone Routing Worksheet – Trouble (Non-Fire Trouble) Report Type Phone 1 Phone 2 Phone 3 Pho
ملخص المحتوى في الصفحة رقم 15
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 15 Table 10: Phone Routing Worksheet – Open/Close Report Type Phone 1 Phone 2 Phone 3 Phone 4 x x Point Opening x x Late to Open x x Closing Early x x Extn Close Time Perim Dlay Armed x x F Close Early x x F Close Pr Dlay x x Command Bypass Swinger Bypass x x Early to Open x x Fail to Open x x Closing Late Fail to Close x x Was Force Armed x x F Close Late x
ملخص المحتوى في الصفحة رقم 16
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 16 Table 12: Phone Routing Worksheet – Test/Stat Rpt (Test and Status Reports) Report Type Sub Group Phone 1 Phone 2 Phone 3 Phone 4 Test Report (Includes expanded panel wide events as shown) Log Threshold Prog Access OK SDI Failure Battery Missing Pt Bus Trouble AC Failure Log Overflow Bad Call to RAM Comm Failure Battery Low User Tamper Params B
ملخص المحتوى في الصفحة رقم 17
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 17 Table 14: Phone Routing Worksheet – Power/Phone Report Type Phone 1 Phone 2 Phone 3 Phone 4 x x Comm Restoral x x AC Failure x x Battery Low x x Phone Line Fail x x AC Restoral x x Battery Restore Phone Restoral Battery Missing Table 15: Phone Routing Worksheet – Service Report Type Phone 1 Phone 2 Phone 3 Phone 4 x x Usr Code Change x x Prog Access Bad x x
ملخص المحتوى في الصفحة رقم 18
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 18 Ph# Test/Stat Rpt Ph# Relay Default: Blank Default: Blank Selection: Blank, P, B, or D Selection: Blank, P, B, or D See the introduction to Phone Routing for a See the introduction to Phone Routing for a description of the selections. description of the selections. Test reports and Status reports are enabled in the Ph# Skeds Skeds section of the program. For Test reports, see Sked Function Code #9. For Status reports, see
ملخص المحتوى في الصفحة رقم 19
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 19 Ph# Service AC Tag Along Send AC Failure report as an additional message Default: Blank (tag along) with other reports. To comply with UL Selection: Blank, P, B, or D 864 requirements for Commercial Fire Systems, program AC Tag Along YES. See the introduction to Phone Routing for a description of the selections. Default: No 1.3 Power Supervision Selection: Yes or No AC Fail Time Yes When AC fails, the report is not s
ملخص المحتوى في الصفحة رقم 20
D9112B | Program Entry Guide | 1.0 Panel Wide Parameter EN | 20 Bat Fail/Res Rpt The battery must be discharged below 12.1 VDC for Determines if battery (DC) power supervision 16 sec. before the D9112 responds to a low battery reports are sent. (see the D9112 Operation and Installation Guide for discharge schedule). Default: Yes Selection: Yes or No Yes Battery Failure and Restoral reports are sent to the central station. They are routed to the telephone number programmed for Power
