ملخص المحتوى في الصفحة رقم 1
E-TBT-MC04 10Base-T
Transceiver
• Stand-Alone model
• Attached Unit Interface (AUI) to
Ethernet RJ-45 connectors
• No external power requirement
The E-TBT-MC04 transceiver is a media access
unit (MAU) that connects the AUI port of data
terminal equipment, repeaters, or other network
devices either directly or through an AUI cable to an Ethernet 10BASE-T device. The
Ethernet device is connected to the transceiver through an unshielded or shielded
twisted-pair copper cable with RJ-45 connector e
ملخص المحتوى في الصفحة رقم 2
E-TBT-MC04 E-TBT-MC04 General Description E-TBT-MC04 Features • Provides a complete interface of the AUI to Ethernet UTP cable. The E-TBT-MC04, IEEE802.3 compliant Ethernet transceiver uses 10Mbps Ethernet CSMA/CD protocol to provide a connection interface to 10Base-T Ethernet unshielded • Supports 10Mbps data transfer rates. twisted-pair (UTP) cables. The transceiver connects to the AUI connector of an • Supports Carrier Sense Multiple Access/Collision Detection (CSMA/CD) Ethernet device via st
ملخص المحتوى في الصفحة رقم 3
E-TBT-MC04 E-TBT-MC04 Connectors & Cables -- Continued Connectors & Cables -- continued AUI connector -- continued UTP cable (RJ-45 connector) -- continued Table 1: AUI Male Connector Pinouts Table 2: RJ-45 Pin Assignments Pin Name Pairs Use Pin Out Jack Assignments 3 DO + Transmit Data Out + 1 Outgoing Data 1 (+) 10 DO - Pair Data Out - 2 Outgoing Data 2 (-) 11 DO S Data Out Shield 3 Incoming Data 1 (+) 5 DI + Receive Data In + 4 Not connected 12 DI - Pair Data In - 5 Not connected 4 DI S Da
ملخص المحتوى في الصفحة رقم 4
E-TBT-MC04 E-TBT-MC04 Installation -- Continued Installation Connecting to a Device AUI port Switches The E-TBT-MC04 can connect to any Ethernet device with an AUI port. To connect to The E-TBT-MC04 has a 3-position DIP switch. See Figure 6. Two of the switches a device with an AUI port, an AUI cable or direct connection is required. See Figure 7. provide options for enabling and disabling the SQE test and LINK test functions. Both test functions are Ethernet and 10Base-T standards. SW2 SW1 SW3
ملخص المحتوى في الصفحة رقم 5
E-TBT-MC04 E-TBT-MC04 Operations Technical Specifications For use with Transition Networks’ Model E-TBT-MC04 or equivalent. LEDs Standards IEEE 802.3ab, IEEE 802.3 Figure 9 shows the E-TBT-MC04 LEDs: Data Rate 10 Mb/s Dimensions 1.77" x 0.81” x 3.14" (44.96 mm x 20.57mm x 79.76mm) Receive Status Weight 0.2 lbs. (90.72 g) approximately Power Consumption Not to exceed 75mA @ 12VDC Power Source AUI port, 500 mA @ 12VDC Operating Temp 0 to 50°C (32°F to 122°F ) Storage Temp: -25 to 85°C (-13°F t
ملخص المحتوى في الصفحة رقم 6
E-TBT-MC04 E-TBT-MC04 Cable Specifications Contact Us The physical characteristics of the media cable must meet or exceed IEEE 802.3 Technical support specifications. Technical support is available 24 hours a day. US and Canada: 1-800-260-1312 Copper cables International: 00-1-952-941-7600 Category 3: (minimum requirement) Transition now Gauge 24 to 22 AWG Chat live via the Web with Transition Networks Technical Support. Attenuation 11.5 dB/100m @ 5-10 MHz Log onto www.transition.com and click
ملخص المحتوى في الصفحة رقم 7
E-TBT-MC04 Compliance Information CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A&B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause ha
