ملخص المحتوى في الصفحة رقم 1
DP 6000 DIGITAL PAGING SYSTEM
INSTALLATION
69
INSTRUCTIONS
December 1997 Page 1 of 15
FIELD CONTROL PANEL LBB 6005
holder, whereas in the latter, the PST holder must, within a
INSTALLATION INSTRUCTIONS
predetermined time, acknowledge that a call has been received by
pressing the Alarm Reset Button on the PST.
1 GENERAL INFORMATION
When the auto-scan facility is programmed and set for user
enable/inhibit, the auto-scan facility will be activated by pressing the
For a detailed description of DP
ملخص المحتوى في الصفحة رقم 2
DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 2/15 During programming, the desk display will show the program 2.5 Bleep Tones information as it is entered. The following bleep tones can be heard during programming : Use the DIRECT CALL key of the desk to select the correct FCP number (if more than one connected ) the PROGRAM key to enter 0.2 seconds the selected data and scroll on to the next command. (a) Key confirmation If a call string is selected and the RE
ملخص المحتوى في الصفحة رقم 3
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 3/15 December 1997 3 FCP PROGRAMMING 3.1 PS 6000 menu selection To enter the PS 6000 menu, OPEN THE DESK EDITOR, SELECT and PRESS key “A”as shown in para. 2.3 and observe the correct display indication. DISPLAY “PS menu” When the PS 6000 menu is opened, the following sub menus can be selected to program the FCP. KEYSTROKE SUB MENU C Communications/Initialisation DIRECT CALL KEY Direct Call info MONITOR KEY Call FCP setting A A
ملخص المحتوى في الصفحة رقم 4
DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 4/15 COMMMAND “3” - ALLOCATE ADDRESS DISPLAY SHOWS “GIVADR (1/0)” Keystroke “1” - Will give the connected uninitialised FCP the lowest free (unallocated) address automatically.(see also Command 4) After the keystroke the desk will return to the communication menu Eronneous keystokes will generate the error bleep and return to the “Comm. menu” Keystroke :0” - Return to “Communication menu”. COMMAND “4” - FCP STATUS
ملخص المحتوى في الصفحة رقم 5
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 5/15 December 1997 4.3 Address Status Changing within Command “4” (STA FCP NR.) Submenu: The following gives the correct key selections necessary to move from one status to another: FROM TO KEY IN FROM TO KEY IN “Present” “Allocate” 0 - 1 “Unalloc” “Present” 1 - 1 “Present” “Unalloc” 0 - 2 “Unalloc” “Allocate” 1 - 1 - 0 - 1 “Present” “Reply MB” 1 - 3 “Unalloc” “Reply MB” 1 - 1 - 1 - 3 “Allocate” “Present” 1 - 1 “Reply MB” “Present”
ملخص المحتوى في الصفحة رقم 6
DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 6/15 5.3 EDITING THE ALARM CALL STRING The display will show “FCP Nr., Channel Nr., “a” and the call string (e.g. 0105a - - - - - - - - - -). The alarm call data can be edited using the hex. key pad (Address- 4 digits / Codinf -1 digit / Info - 5 digits). This call will be transmitted if: a) An internal relay is programmed. b) The alarm call is enabled for this relay c) The relay delay time is over. Press PROGRAM key to
ملخص المحتوى في الصفحة رقم 7
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 7/15 December 1997 5.8 MANUAL ACKNOWLEDGE TIME The display will show “FCP Nr. and Channel Nr. followed by “ack. time” followed by the programmed time (e.g. 0105 ACK TIME - - - ) Enter the desired time from 000 - 254 seconds (The time may not be set to 255 seconds) Press the PROGRAM key. The display will show “Update?” A further PROGRAM keystroke will update the new programmed data and scroll to the next channel Direct Call Editor.
ملخص المحتوى في الصفحة رقم 8
DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 8/15 The display will now show “Sel. Chan. Nr”, select the channel to be edited (01 - 16) and the display will show the programmed auto scan status of the channel e.g. “e c xx a m yy - 1 - zz” Location = 1 2 3 4 5 6 7 Where e = auto scan enabled (or “d” for auto-scan disabled) c = codinf value for an auto scan with manual acknowledge (see table 2, bleep patterns). xx = auto scan repeat time in m
ملخص المحتوى في الصفحة رقم 9
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 9/15 December 1997 8.1 FUNCTION ASSIGNMENT The display will now show the current setting of the FCP e.g. Function position - 1 2 3 4 5 6 7 8 9 Display shows - “A I I S I I I xx y” (xx = FCP Nr. ; y = Relay Nr.) Enter the required status by keying in position Nr. 1 - 7, followed by keystrokes “0” or “1” Keystroke “0” inhibits the function and the display will indicate “I” in this positio
ملخص المحتوى في الصفحة رقم 10
DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 10/15 9. WIRING DETAILS X1 - 9-pin D-type socket for connection to the High Performance desk (LBB 5800) Pin No. Function 1 +12 V power supply from the desk (fused at 1 AT) 2 not connected 3 not connected 4 RS 422 serial int. B (extra 220 Ohm) X2 X1 50 V 6 + 12 V power supply from the desk (fused 1 AT) 7 not connected 8 RS 422 serial int. A (extra 220 Ohm) 90 V screening not connected X2 - 9-pin D-type socket for externa
ملخص المحتوى في الصفحة رقم 11
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 11/15 December 1997 PS 6000 and DP 6000 SYSTEM WIRING Installation details of the various units in the PS 6000 system can be found in the relevant Installation Instructions:(see contents) 3 x external relay outputs
from each FCP DP 6000 PAGING LINE PSU* 16-pin Hirschmann 12 3 4 5 6 7 8 Plug Socket FCP type LBB 6005/00.
1 Each FCP can cater for
up to 16 transceivers.
A max. of 31 FCPs can
be used off one desk.
FCP PSU* FCP cons
ملخص المحتوى في الصفحة رقم 12
Enter Light Menu Enter Light Menu Enter Light Menu P P P Alarm Recall Alarm Recall Alarm Recall DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 12/15 Mains LBB 6015 CENTRAL
TRANSMITTER LBB 6010 or
LBB 6110 VHF or UHF
Central Transmitter
VHF or UHF Central Talk-back
Receiver with
PSU* Pilot-tone Decoder LBB 6015 Mains *Power Supply Unit (PSU)
LBB 5834. Quantity depends
on system configuration. If more
Personal Security Transceivers
than one FCP is used th
ملخص المحتوى في الصفحة رقم 13
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 13/15 December 1997 TABLE 1 FCP DEFAULT VALUES FUNCTION DEFAULT VALUE FCP Address (not inialised) h “50” Relay 1, 2, 3, function assignment I I I I I I I Relay 1, 2, 3, delay time 30 seconds Relay 1, 2, 3, pulse time 00 (pulse inhibit) Relay 1, 2, 3, standby status energised Relay 1, 2, 3, alarm call transmission inhibit Call Desk/FCP Nr. Call Desk/FCP Nr. 1 and 2 Direct call all channels inhibit Direct call string 0 0
ملخص المحتوى في الصفحة رقم 14
DP 6000 DIGITAL PAGING SYSTEM INSTALLATION INSTRUCTION 69 December 1997 Page 14/15 TABLE 3 The codinf value transmitted by the PST during any kind of acknowledge/alarm call is assigned a particular status in the FCP. This TABLE lists the codinf digit and status of the each in the FCP. CODINF DIGIT FUNCTION 0 The alarm LED status is updated to “no move switch off” When no acknowledge is expected, then “call desk function will be activated when FCP set for “call panel.1” When acknowledge is exp
ملخص المحتوى في الصفحة رقم 15
INSTALLATION INSTRUCTION 69 DP 6000 DIGITAL PAGING SYSTEM Page 15/15 December 1997 123456 7 8 9 10 11 16 15 14 13 12 LBB 5800 High Performance Control Desk Key to symbols 1. Handset (LBB 5804 optional) : Can be use instead of the desk microphone and speaker 2. Display window : LCD to display 16 digit information 3. Power On indicator (LED) : Green 4. Transmission On indicator (LED) : Red 5. Desk-in-use indicator (LED) : Yellow 6. Program key : Used to program the desk and additional receivers i
