ملخص المحتوى في الصفحة رقم 1
ADDENDUM
Addendum No. C1573M
Date February 1, 2006
Manuals Affected C1572M, C1555M-F, C1566M-C
Manual Update The front and rear mounting rails and the mounting brackets are no longer supplied with the CM9700-CC1.
Disregard the CM9700-CC1 mounting information in the above referenced manuals.
To mount the CM9700-CC1 into a standard 19-inch EIA rack follow these instructions:
1. Insert the CM9700-CC1 into the rack.
2. Tighten the CM9700-CC1 to the rack using the four supplied Phi
ملخص المحتوى في الصفحة رقم 2
INSTALLATION/OPERATION System 9780 ® C1566M-C (10/05)
ملخص المحتوى في الصفحة رقم 3
Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 List of Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 List of Tables . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 4
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Regulatory Notices . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 5
List of Illustrations 1 CM9780-MXB Mounting Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2 Mounting the CM9780-MXB on Top of the Mounting Baffle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 3 Mounting the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 6
List of Tables A LEDs Illuminated During a Basic Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 B Data Connections—Single Node Systems Without a Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 C Data Connections—Networked System Without a Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 7
Description The System 9780 is a full-featured video matrix switching control system that allows you to view and control up to 4,096 cameras and 512 monitors on a single node. Video patch panels (CM9700-VPP) allow you to connect up to 512 cameras on each CM9780-MXB bay compared to 256 cameras on the System 9770. The System 9780 has the following basic components: • CM9700-CC1—This is the system CPU; connect matrix bays, keyboards, PTZ camera control lines, and peripheral devices to
ملخص المحتوى في الصفحة رقم 8
Network Interface Unit CM9700-NW1 Network interface unit; network CPU and software necessary for joining two or more independent systems together. Keyboards The following keyboards are compatible with the System 9780: CM9760-KBD Full-function desktop variable-speed keyboard; 120 VAC, 60 Hz. CM9760-KBD-X Same as CM9760-KBD except 230 VAC, 50 Hz. CM9760-KBR Full-function 19-inch EIA rack mount keyboard; 120 VAC, 60 Hz. CM9760-KBR-X Same as CM9760-KBR except 230 VAC, 50 Hz. NOTE
ملخص المحتوى في الصفحة رقم 9
Installation UNPACKING 1. Unpack and inspect all equipment, and verify delivery according to the packing slip. Before shipping, Pelco connects, tests, and programs each system according to the individual sales order. Contact Pelco immediately if there is any discrepancy in the equipment that you receive. CM9700-CC1 The following items are supplied with the CM9700-CC1: • 1 CM9700-CC1 unit, with front rack ears installed • 1 120 VAC, 60 Hz power cord (USA standard) • 1 230 VAC, 5
ملخص المحتوى في الصفحة رقم 10
MOUNTING Install the System 9780 in EIA-standard, 19-inch (48.26 cm) racks. CM9780-MXB 1. Install the CM9780-MXB mounting baffle first (refer to Figure 1). The mounting baffle uses 1 rack unit (RU), and it has front and rear mounting ears, which are attached to the front and rear mounting rails. The rear mounting brackets are adjustable to allow for different depths of cabinets. NOTE: Be sure to use all eight screws provided with the mounting baffle. The mounting baffle must be i
ملخص المحتوى في الصفحة رقم 11
Figure 2. Mounting the CM9780-MXB on Top of the Mounting Baffle 3. (Optional) Install additional CM9780-MXB mounting trays and matrix bays to the side of and below the first unit, as necessary. WARNING: Always install equipment starting from the bottom of the rack frame or cabinet. Installing equipment from the top down will make a rack or cabinet top heavy and could cause the equipment to tip over. NOTE: Each CM9780-MXB has a unique label for identifying the bay location in t
ملخص المحتوى في الصفحة رقم 12
3. Attach one set of support rails to the equipment rack in the desired location as follows: a. Position the ear of the front-mounting support rail against the front of the equipment rack and align the holes in the ear of the rail with the threaded holes in the rack. Attach the ear of the rail to the rack using two 10-32 x 0.375-inch flat head screws. b. Adjust the support rails to the correct depth of the equipment rack by sliding the rear-mounting support rail to the back of the equ
ملخص المحتوى في الصفحة رقم 13
CM9700-VPP There are two ways you can mount a CM9700-VPP video patch panel into a rack. 1. Single panels into a rack 2. Up to 16 panels using the CM9700-VPP-RK The following illustration shows how to mount a single panel into a rack. The panel is mounted horizontally. You can mount multiple panels horizontally. This takes up more rack space than if using the CM9700-VPP-RK. RACK CABLE CM9700-VPP BRACKET (4) SCREWS, 10-32X3, PHILLIPS RACK PANHEAD WITH WASHERS MOUNT BRACKET Figure 4. C
ملخص المحتوى في الصفحة رقم 14
VIDEO INPUT/OUTPUT CONNECTIONS The following steps provide an overview of how to connect video input and output sources. More complete procedures are provided in the subsequent sections. NOTE: If your System 9780 is configured by Pelco, the appropriate number of video input cards and monitor output cards and BNC and DFC rear panels are installed at the factory, and steps 1 and 2 are not necessary. If this is the case, skip to Step 3. 1. Install the CM9780-VCC and CM9780
ملخص المحتوى في الصفحة رقم 15
INSTALLING VIDEO INPUT CARDS (CM9780-VCC) Video input cards are inserted into every slot, starting with slot 1 (refer to Figure 6). To add a video card, slide the card into the first slot. Continue as necessary, using every slot, up to a maximum capacity of sixteen video input cards. HOT SWAPPING: You can “hot swap” a video input card—remove a card and/or insert a new card—while the system is powered and running. When you hot swap a card, the CM9780-MXB automatically veri
ملخص المحتوى في الصفحة رقم 16
INSTALLING MONITOR OUTPUT CARDS (CM9780-VMC) The monitor output card located in slot 18 is the primary card, and it handles video for monitors 1-16. Refer to Figure 7. Note that the CM9780-MXB will not function without a CM9780-VMC card inserted into slot 18. An optional secondary VMC card can be installed in slot 17. This card routes video for monitors 17-32. HOT SWAPPING: You can “hot swap” a monitor output card—remove a card and/or insert a new card— while the system is power
ملخص المحتوى في الصفحة رقم 17
PERFORMING A BASIC LED CHECK You should perform a basic LED check before you connect any video input or output to the matrix bay. The LED check allows you to make sure that the system is operating properly. 1. Turn on the power switch on the rear of the matrix bay. The front cover can either be open or closed during the LED check. 2. Various LEDs will blink during the initialization process as the software verifies communication and version level information. Once the ini
ملخص المحتوى في الصفحة رقم 18
INSTALLING REAR PANEL CARDS The following rear panel cards can be used with the CM9780-MXB matrix bay: • CM9780-DFC—This card is used to connect video ribbon cables from the CM9700-VPP video patch panels (this card can also be used for sideframing, downframing, and looping video; refer to the Looping Video section and to the Sideframing and Downframing sections in the Appendix for more information). • CM9780-RPM—This is the BNC card for monitor connections. • CM9780-
ملخص المحتوى في الصفحة رقم 19
JP32 JP31 JP30 JP29 JP28 JP27 JP26 JP10 JP25 JP16 JP9 JP24 JP15 JP8 JP23 JP14 JP7 JP22 JP13 JP6 JP21 JP12 JP5 JP20 JP11 JP4 JP19 JP3 JP18 JP2 JP17 JP1 TERMINATED UNTERMINATED 3 2 1 When looping video out to another device (such as a DVR, VCR, or switcher), set the termination jumpers on the CM9780-DFC cards to the unterminated position. INPUT FROM CM9700-VPP PATCH PANEL – CONNECTOR A UNTERMINATED TERMINATED INPUT FROM CM9700-VPP PATCH PANEL – CONNECTOR B Figure 9. DFC Card Insert or R
ملخص المحتوى في الصفحة رقم 20
3. Tighten the screws at the top and bottom of the BNC card. PRIMARY VMC CARD (SLOT 18) OPTIONAL: SECONDARY VMC CARD (SLOT 17) 2 CM9780-RPM BNC PANELS (SECOND PANEL OPTIONAL) Figure 10. CM9780-MXB Matrix Bay—16 Monitor Output Connections for Each VMC Card C1566M-C (10/05) 19
