ملخص المحتوى في الصفحة رقم 1
CS-2004TW1 with 2-Way Paging Remote & 1-Way ‘Sidekick’ Remote
CS-2004DC with two 1-Way Remotes
INSTALLATION & OPERATING INSTRUCTIONS
CONGRATULATIONS on your choice of a Security System by Crimestopper Security Products Inc. This booklet
contains the information necessary for installing, using, and maintaining your 2004TW1 or 2004DC alarm system. If
any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support
number b
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS Installation Cautions & Warnings…….………………………………………………………………...………………2 Suggested Component Mounting………….……………………………………………………………….…………..3 Wiring……..……………………………………………………………………………………………………………….3-5 Power Door Lock Wiring...………………………………………………………………..……………………………6-7 Starter Disable Wiring…………………………..…..……………………………………………………………..……..8 System Wiring Diagram………………….……………………………………………………………………….………9 CS-2004TW1 Antenna Diagram………...……………………………………………………………………….…..…10
ملخص المحتوى في الصفحة رقم 3
CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in the engine compartment or anywhere they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location. The antenna wire should be routed away from any metal if possible. Do not alter the length of the antenna, ground it, or route it with other wires. SIREN MOUNTING: Mount the siren under the hood to
ملخص المحتوى في الصفحة رقم 4
WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switches are available, install new pin switches if desired. GREEN WIRE: (-) DOOR TRIGGER Connect to Negative type door switches that read ground when a door is opened and 12 volts when all doors are closed. In the case of isolated door triggers, you may need to run additional wir
ملخص المحتوى في الصفحة رقم 5
WIRING WHITE/RED WIRE: (-) REMOTE OUTPUT #2 (Optional, Requires Relay) This wire provides a momentary (-) Negative auxiliary Output when Button #4 is pressed and held for at least 2 seconds. Connect this wire to terminal 85 of a relay to operate an AUX device or function. Connect terminal 86 or the relay to +12 Volts constant. Connect terminal 87 to 12Volts or Ground depending to the type of circuit needed. Connect Terminal 30 to the AUX device’s activation wire. This output will sta
ملخص المحتوى في الصفحة رقم 6
POWER DOOR LOCK WIRING 6-PIN DOOR LOCK PLUG 18 GA. (Optional / ON-Board Relays): VIOLET: DOOR LOCK Relay Term. #87: Normally Open [Polarity Input for Lock relay] WHITE: DOOR LOCK Relay Term. #30: Common [Lock Output] GRAY: DOOR LOCK Relay Term. #87A: Normally Closed VIO/WHT: DOOR UNLOCK Relay Term. #87: Normally Open [Polarity Input for Unlock relay] GREEN: DOOR UNLOCK Relay Term. #30: Common [Unlock Output] BLUE: DOOR UNLOCK Relay Term. #87A: Normally Closed
ملخص المحتوى في الصفحة رقم 7
POWER DOOR LOCK DIAGRAMS POSITIVE TRIGGER DOORLOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING BLUE X BLUE X NOT USED X = NOT USED X = GREEN GREEN VIOLET/WHITE VIOLET/WHITE GRAY X GRAY X WHITE WHITE VIOLET VIOLET +12V + FUSED FACTORY FACTORY L L LOCK WIRE LOCK WIRE LOCKING LOCKING UL UL UNLOCK WIRE UNLOCK WIRE RELAYS RELAYS AFTERMARKET MOTOR DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING BLUE BLUE GREEN GREEN VIOLET/WHITE VIOLET/WHITE GRAY GRAY WHITE WHITE VIOLET VIOLET +12V + +12V FUSED FUSE
ملخص المحتوى في الصفحة رقم 8
STARTER DISABLE WIRING STARTER DISABLE PLUG: 3 ORANGE 14 GA. WIRES: (PROGRAMMABLE: Normally Closed or Normally Open Configuration with ON-Board Relay) Note: READ BELOW before connecting starter disable! Normally OPEN must be programmed to operate. See pg 10. Normally Closed Starter disable is the standard type used with most alarm systems today. This circuit will disable the Starter while the alarm is armed or has been triggered. If 12V power is removed from the system, the Battery go
ملخص المحتوى في الصفحة رقم 9
SYSTEM WIRING DIAGRAM BLACK 3-PIN POLARITY SELECT LOCK(87) CUT CS-2004TW1 Antenna LOCK OUTPUT(30) LOCK SWITCH(87A) STARTER POLARITY SELECT UNLOCK(87) VIOLET UNLOCK OUTPUT(30) WHITE UNLOCK SWITCH(87A) GRAY IGNITION VIO/WHT N/O SWITCH GREEN BLUE 87 85 N/O (-)DOME LIGHT N/C 30 86 COMMON BLACK/WHITE CS-2004TW1 N/C STARTER DISABLE 87 85 (-)REMOTE OUTPUT 2 CS-2004DC WHITE/RED 30 86 (-)REMOTE OUTPUT 1 87 85 GRAY 30 86 + CAR-JACK ENABLE PINK + DOOR TRIGGER VIOLET (-)DOOR TRIGGER SWITCH GREEN (-)HOOD/TR
ملخص المحتوى في الصفحة رقم 10
CS-2004TW1 ANTENNA The following diagram pertains to the CS-2004TW1 model only: RECOMMENDED ANTENNA LOCATIONS WINDSHIELD CS-2004TW1 Antenna System Window Mount Antenna Transceiver Box Blue Plug Note Orientation of Black & Blue Plugs. Colors must match, or system will not operate! CS-2004TW1 Black Plug 10
ملخص المحتوى في الصفحة رقم 11
OPTION PROGRAMMING To Engage Option Programming: 1. Turn Key to the ON position and wait 5 seconds. 2. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times and the LED will light solid. 3. Push the valet/program button [again] the number of times that corresponds to the option number desired (1 thru 13). Press so that you get a light flash after each button press. If the unit did not flash the lights, then it did not register your press. Se
ملخص المحتوى في الصفحة رقم 12
OPTION PROGRAMMING 2. PASSIVE ARMING This option controls the Passive (Automatic) arming feature. If ON, arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The LED will begin flashing rapidly. If a door is reopened, the system will wait (LED solid) for the door or zone to close before arming. 3. ACTIVE RE-ARM Active Re-arming allows the system to re-arm itself 30 seconds after disarmed with the transmitter if a door has not been opened.
ملخص المحتوى في الصفحة رقم 13
OPTION PROGRAMMING 11. DOUBLE UNLOCK PULSE This option controls whether the unit will send one or two unlock pulses when disarmed. This feature may be required for interfacing to existing Factory Keyless Entry or Alarm systems in a vehicle. These systems are found on some Nissan, VW, Toyota, and Lexus vehicles. 12. ENABLE/DISABLE CARJACK FEATURES This option controls the unit’s Car Jack features. Enable or Disable Carjack (Turn ON or OFF) with this option. 13. STARTER DISABLE CO
ملخص المحتوى في الصفحة رقم 14
CS-2004TW1 / CS-2004DC TRANSMITTER PROGRAMMING SEE NOTES LAST PAGE! 1. Turn key to the ON position and wait 5 seconds. 2. Press Programming/Valet button 4 times. 3. After a few seconds, the unit will flash the parking lights 4 times. 4. A. FOR CS-2004TW1: Press Buttons #1 & 2 together on the remote you wish to program. B. FOR CS-2004DC Press the Button #1 (Lock) on the remote you with to program. nd 5. You should get 2 light flashes indication the unit is waiting for a 2 code, th
ملخص المحتوى في الصفحة رقم 15
OPERATION CS-2004DC / CS-2004TW1 remote controls: FIXED PAGING ANTENNA #2 LED's DISARM #1 UNLOCK ARM/ LOCK #2 #1 NOT DISARM/ ARM/ USED UNLOCK LOCK AUX SLNT #3 AUX. #1 #4 #4 SILENT/ AUX #3 SLNT SILENT/ AUX. #2 AUX. 1 AUX. 2 CS-2004DC REMOTE CS-2004TW1 ONE-WAY REMOTE CS-2004TW1 LED PAGING REMOTE CS-2004TW1 TWO-WAY PAGER OPERATION & PAGE TONES: PAGE-BACK: FEATURE BUTTON ACTION BEEPS LED/FLASH ARM/LOCK #1 (Lock) Press & Releas
ملخص المحتوى في الصفحة رقم 16
OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter will be disabled. The red in- dash LED in the vehicle will begin to flash. After a short delay of 10-15 seconds to allow vehicle and electronics to stabilize the system will be completely armed. DISARMING To disarm the alarm and unlock the doors, press the
ملخص المحتوى في الصفحة رقم 17
OPERATION SHOCK / IMPACT PROTECTION WITH PRE-WARNING Once the system is armed, if a low-level shock to the vehicle body is detected, the pre-warning sensor activates with 5 siren chirps and one light flash as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle for 20 seconds. Adjust the shock sensor as needed by turning the control knob clockwise or counter-clockwise to increase or decrease the sensitivity. Shock sensors will “s
ملخص المحتوى في الصفحة رقم 18
OPERATION PASSIVE ARMING / PASSIVE LOCK MODES If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The lights will flash twice when the last door is closed and the LED will begin flashing rapidly while counting down. If a door is reopened the countdown will reset and, the system will wait for the door or zone to close before starting 30 second countdown again. The unit will chirp once and flash the lights on
ملخص المحتوى في الصفحة رقم 19
OPERATION LED TRANSCEIVER (LOW BATTERY WARN) Twist and Remove CS2004TW1 Battery cover with The CS-2004TW1 LED has a low battery warning system. BATTERY a Coin or Screwdriver When the battery voltage is low, the LED pager remote will REPLACEMENT stop beeping and flash the Orange & Green LEDs when buttons are pressed. We recommend replacing the battery for proper operation. Use a small coin to twist open the battery Larger "+" Positive compartment and replace the CR2032 Lithium battery
ملخص المحتوى في الصفحة رقم 20
CARJACK PROTECTION PROGRAMMABLE PASSIVE CARJACK This feature provides Passive Carjack protection and must be enabled before use through Alarm programming options #7 & #12 on page 10. We recommend this mode should only be used in serious situations. When the Ignition is on (vehicle is running), and a door is opened, then closed, the Carjack countdown sequence will automatically be initiated. 60 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre- warning c
