ملخص المحتوى في الصفحة رقم 1
D9000,G & GV2 Series
Owner’s Manual Supplement
D9000, G & GV2
EN Series
ملخص المحتوى في الصفحة رقم 2
D9000,G & GV2 Series | Owner's Manual Supplement Contents 1.0 Introduction .......................................................3 2.0 Two-Man Rule...................................................3 2.1 Description.............................................................3 2.2 Using the Two-Man Rule.......................................3 3.0 Early Ambush....................................................4 3.1 Description.........................................................
ملخص المحتوى في الصفحة رقم 3
D9000,G & GV2 Series | Owner's Manual Supplement 1.0 Introduction This document supplements the Security System Owner’s Manual (P/N: 71-06633-000) with the Function List features for the D9000 Series. The instructions for the commands listed in this document replace those commands in the Security System Owner’s Manual. Refer to the Owner’s Manual for the operation of your new security system and its other basic Function List features. Place this supplement inside the Security Sys
ملخص المحتوى في الصفحة رقم 4
D9000,G & GV2 Series | Owner's Manual Supplement [ENTER] key. The second pass code must be different from the first pass code. The area is disarmed and ready for entry. 3.0 Early Ambush 3.1 Description Early Ambush adds an extra step to the disarm process by requiring an additional pass code to be entered to confirm the area is secure. The second pass code can be same as the first or a different one, depending on the configuration. The first entry disarms the area and the second entr
ملخص المحتوى في الصفحة رقم 5
D9000,G & GV2 Series | Owner's Manual Supplement 4.0 Easy Exit Control 4.1 Description The D9412GV2 / D7412GV2 Control Panels change from one armed state to another armed state without disarming. The Easy Exit Control feature reduces the number of keystrokes and simplifies system operation. This feature is available by default and is always on. 4.2 Using Easy Exit Control Switching armed states from Master to Perimeter: 1. Ensure the keypad shows idle master armed text. 2. Press t
ملخص المحتوى في الصفحة رقم 6
D9000,G & GV2 Series | Owner's Manual Supplement 5.0 Passcode Follows Scope 5.1 Description The Passcode Follows Scope feature is an optional arming and disarming restriction that can be enabled on keypads with access to multiple areas. When this feature is set to No, the keypad restricts Passcode Arming and Passcode Disarming to the home area of the keypad. When set to Yes, this feature allows users to arm or disarm all the areas that they and the keypad have access to. This fe
ملخص المحتوى في الصفحة رقم 7
D9000,G & GV2 Series | Owner's Manual Supplement Arming from a keypad with Panel Wide scope and Passcode Follows Scope disabled (default): 1. Ensure the keypad shows idle disarmed text. 2. Ensure you have a valid pass code with the authority to Passcode Arm in all areas. 3. Enter your code by pressing the [passcode digits] followed by the [ENTER] key. 4. The keypad shows the exit delay count down. 5. Exit the premises. 6.0 Passcode-Controlled Menu 6.1 Description When enabled, t
ملخص المحتوى في الصفحة رقم 8
D9000,G & GV2 Series | Owner's Manual Supplement On a D1260 keypad with the Passcode Controlled Menu enabled: 1. Press the [Menu>] soft key in the lower right corner. The keypad responds with the Enter passcode: then press [ENTER] display. 2. Enter your code by pressing the [passcode digits] followed by the [ENTER] key. The first and second menu items that you have authority to use appear. 7.0 Invisible Walk Test 7.1 Description The D9412GV2 / D7412GV2 has a function list menu item
ملخص المحتوى في الصفحة رقم 9
D9000,G & GV2 Series | Owner's Manual Supplement 7. Press the [ENT] key to view the point’s hardware state: 1PT### NORMAL HW if it is normal 1PT### OPEN HW if it is opened 1PT### SHORT HW if it is shorted 1PT### MISSNG HW if it is missing 8. Activate the point’s sensor and observe the appropriate state change. 9. Press the [NEXT] key to advance to the next invisible point within the scope of the keypad. 10. Repeat steps 7 through 9 until all points are tested. On a D1260 keypad wit
ملخص المحتوى في الصفحة رقم 10
D9000,G & GV2 Series | Owner's Manual Supplement 8.0 Door Activated Custom Function 8.1 Description The D9412GV2 / D7412GV2 allow a custom function to be activated when user credentials are presented to a D9210B Door Controller Reader. The custom function executes as if the user performed a function at the keypad that is associated with the door controller. I have this feature. I do not have this feature. 8.2 Using Door Activated Custom Functions: Executing the door’s custom
ملخص المحتوى في الصفحة رقم 11
D9000,G & GV2 Series | Owner's Manual Supplement 9.2 Using ACCESS LEVEL CTL? 1. Ensure the display shows idle disarmed text. 2. Press the [MENU] key to enter the Function List, then press [NEXT] repeatedly until you reach the CHANGE LEVEL CTL? prompt. Press [ENT]. 3. ACCESS LEVEL CTL appears indicating that you are affecting the authority levels of cards or tokens and not passcodes. Press [ENT]. 4. ENTER LEVEL: appears. Enter the access authority level number and press [ENT]. 5. If
ملخص المحتوى في الصفحة رقم 12
D9000,G & GV2 Series | Owner's Manual Supplement 10.0 Door Control 10.1 Description There are three sub-functions within the door control function. They are CYCLE DOOR?, UNLOCK DOOR? and SECURE DOOR?. CYCLE DOOR? momentarily unlocks a door to allow a person into an area. UNLOCK DOOR? unlocks a door to allow free access. SECURE DOOR? unlocks a door and prohibits access regardless of a user’s authority level. I have this feature. I do not have this feature. 10.2 Using Door Contr
ملخص المحتوى في الصفحة رقم 13
D9000,G & GV2 Series | Owner's Manual Supplement 10.3 Cycle Door? 1. To momentarily unlock an access door and allow a person into an area, press [ENT] at the Cycle Door? prompt. The display shows CYCLE 1 2 3 4 5 6 7 8 if all doors are in a normal state and available. If a door is not in a normal state, the number of the door is replaced with one of the symbols indicated in Table 1. Table 1: Key to Symbols Symbol Description --- Door is not active, not in scope, or user does
ملخص المحتوى في الصفحة رقم 14
D9000,G & GV2 Series | Owner's Manual Supplement 10.4 Unlock Door? 1. To unlock a door to allow free access, at the CYCLE DOOR? prompt, press [NEXT] to enter the UNLOCK DOOR? subfunction. The display shows UNLOCK 1 2 3 4 5 6 7 8 if all doors are in a normal state and available. If a door is not in a normal state, the number of the door is replaced with a symbol indicated in Table 1. 2. Enter the number of the door to unlock then press [ENT]. This door unlocks and the display changes
ملخص المحتوى في الصفحة رقم 15
D9000,G & GV2 Series | Owner's Manual Supplement This indicates that all doors are in a normal state, except for Door 5, which is secured. Press [ESC] to leave this subfunction, or enter another door number to unlock. Each of these subfunctions acts as a toggle switch. To return a door to its normal state, follow the same procedure used to change its state. For example, if Door 3 is secured, to return it to its normal state, at the SECURE DOOR? prompt, enter [3] and press [ENT]
ملخص المحتوى في الصفحة رقم 16
D9000,G & GV2 Series | Owner's Manual Supplement You can use the Function List in place of steps 2 and 3 to start this function. 1. Press the [MENU] key to enter the Function List. 2. Press [NEXT] repeatedly until you reach the DEL USER? prompt. 3. Press [ENT]. 4. The display shows DEL USER #. Enter the user number and press [ENT]. 5. USER ## (or user text, such as the name of the user, if this feature was programmed into your system by your security company) appears allowin
ملخص المحتوى في الصفحة رقم 17
D9000,G & GV2 Series | Owner's Manual Supplement 12.0 Add/Change User - [COMMAND 56] 12.1 Description Use this function to add or change a passcode or card without assistance from your security company. Before adding or changing a passcode or card, you must know which user numbers are available, the authority level you want to assign to the new user, and the areas in which the passcode or card are valid. I have this feature. I do not have this feature. 12.2 Using Add User ? 1
ملخص المحتوى في الصفحة رقم 18
D9000,G & GV2 Series | Owner's Manual Supplement appears. Enter the new passcode followed by [ENT]. ENTER AGAIN appears. Enter the new passcode a second time for confirmation. Press [ENT]. The display shows PASSCODE ADDED (or PASSCODE CHANGED if the user number was already in the system). The system does not accept a passcode that is within two digits of an existing passcode. This is to avoid conflicts with duress passcodes. For example, if passcode 123 is already programmed in
ملخص المحتوى في الصفحة رقم 19
D9000,G & GV2 Series | Owner's Manual Supplement Systems With Access Control... SUB USER ID? appears. Press [ENT]. SUB USER #? appears. Enter 1, 2, or 3 for the desired Sub-User and press [ENT]. PRESENT CARD appears. Present the card or token at the reader and wait for the tone. After the tone sounds the display shows CARD ADDED (or CARD CHANGED if the Sub User number already existed). At the end of each function, press [ESC] to return to the ENTER USER # prompt. Press [ESC] a
ملخص المحتوى في الصفحة رقم 20
Bosch Security Systems 130 Perinton Parkway Fairport, NY 14450-9199 Customer Service: (800) 289-0096 Technical Support: (888) 886-6189 © 2005 Bosch Security Systems 33267F
