ملخص المحتوى في الصفحة رقم 1
MEDIA
D320 DIGITIZER
R9850710
OWNER’S MANUAL
05112002 R5976388/03
ملخص المحتوى في الصفحة رقم 2
Barco nv Media Noordlaan 5, 8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: media@barco.com Visit us at the web: www.barco.com Printed in Belgium
ملخص المحتوى في الصفحة رقم 3
Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO. Guarantee and Compensation Barcoprovidesaguaranteerelatingtoperfectmanufacturingaspartofthelegallystipulatedtermsofguarantee. Onreceipt,thepurchaser must immediately inspect all delivered goods for damage incurred during transport, as wellas for material and manufacturing faul
ملخص المحتوى في الصفحة رقم 4
ملخص المحتوى في الصفحة رقم 5
Revision Sheet To: Barco nv Media/Documentation Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70, Fax: +32 56.36.88.24 E-mail: antoon.dejaegher@barco.com, Web: www.barco.com From: Date: Please correct the following points in this documentation (R5976388/03): page wrong correct R5976388 D320 DIGITIZER 05112002
ملخص المحتوى في الصفحة رقم 6
ملخص المحتوى في الصفحة رقم 7
Table of contents TABLE OF CONTENTS 1. Safety..................................................................................................................3 1.1 Important Safety Instructions........................................................................................................... 3 1.2 Important Warnings..................................................................................................................... 4 2. Introduction ......................................
ملخص المحتوى في الصفحة رقم 8
Table of contents 2 R5976388 D320 DIGITIZER 05112002
ملخص المحتوى في الصفحة رقم 9
1. Safety 1. SAFETY 1.1 Important Safety Instructions Instructions: Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do NOT submerge fully or partly in water or other liquids. Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer for further advice should any doubts exist regarding any cleaning procedure. Do not block ventilation openings. Install in accordance with the
ملخص المحتوى في الصفحة رقم 10
1. Safety 1.2 Important Warnings Important Warnings: Risk of electric shock: Image 1-1 Risk of electrical shock Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with an arrowhead within a triangle isintended to tellthe userthatpartsinside thisproductmaycause a risk of electrical shock to persons. The exclamation point within a triangle i
ملخص المحتوى في الصفحة رقم 11
2. Introduction 2. INTRODUCTION 2.1 General functionality Overview The D320 allows you to controlup to 4 sourceson one display. Seamlessswitch from source to source ordisplay sourcestogether, overlay them, customize them. With analog and digital outputs which allow for the control of displays, as well as built-in-control software, the D320 gives you control over everything from basic set-up to configuration and advanced feature control. 2.2 Order info D320 Digitizer Order info: Article No. Descr
ملخص المحتوى في الصفحة رقم 12
2. Introduction 2.4 Dimensions of the D320 Digitizer Dimensions Image 2-1 6 R5976388 D320 DIGITIZER 05112002
ملخص المحتوى في الصفحة رقم 13
3. Physical Installation 3. PHYSICAL INSTALLATION 3.1 Installation requirements Requirements The Digitizer should not be placed in a built-in installation or enclosure unless proper ventilation is provided. When using the unit in a multi-unit rack assembly or closed assembly, the ambient temperature inside the assembly may not exceed the maximum rated ambient temperature of the Digitizer. The installation should be such that the amount of air flow required for safe operation of the equipment
ملخص المحتوى في الصفحة رقم 14
3. Physical Installation A : Led-wall out -DVI. - Data output source to drive ILite / DLite display wall. B : Power switch - The power ON/OFF switch is provide on the rear side of the Digitizer. o Switch pressed to 1 = the unit starts. o Switch pressed to 0 = unit totally switched off. C : Power input - Autoranging from 90 to 260 VAC / 130 Watt. D : Loop in - From previous Digitizer. - Panel Link MDR26. - Used for chaining multiple digitizer to increase the number of usable input sources
ملخص المحتوى في الصفحة رقم 15
3. Physical Installation How to remove an input module from the D320 Digitizer 1. Push in the release button underneath the input module which you want to remove. At the same time pull out the input module by the grip handle. (image 3-3) Image 3-3 How to insert an input module into the D320 Digitizer 1. Gently slide in the input module into a free input slot with the grip handle at the top. 2. Locking in the module by pushing the input module completely into the Digitizer until a definite click
ملخص المحتوى في الصفحة رقم 16
3. Physical Installation 10 R5976388 D320 DIGITIZER 05112002
ملخص المحتوى في الصفحة رقم 17
4. Input modules 4. INPUT MODULES Overview DVI input module SDI input module HDSDI input module CVBS / S-VID input module YUV / RG(s)B input module RGB analog input module Dummy input module 4.1 DVI input module Technical info: Computer generated graphical source. DVI data in (DVI-I connector). Maximum 162 Mbit/s transmission. Resolution from VGA to UXGA. DVI compliant. DVI loop through (DVI-I connector). Amber LED (upper LED on the front side) will be lit indicating
ملخص المحتوى في الصفحة رقم 18
4. Input modules Image 4-3 Image 4-4 Order info: Article No. Description R9850970 D320 SDI input module 4.3 HDSDI input module Technical info: HDSDI data in (SMPTE292M). HDSDI loop through (SMPTE292M). Coax (75 Ohm). AmberLED(upperLED on thefrontside)willbe lit indicating recognition offilm,eithercontinuousorintermittentfilm detection. When placed in an input slot the green LED (lower LED on the front side) will be lit indicating that the system acknowledge the module. Supported HDSD
ملخص المحتوى في الصفحة رقم 19
4. Input modules Order info: Article No. Description R9850980 D320 HDSDI input module 4.4 CVBS / S-VID input module Technical info: Video (BNC) - CVBS : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination. - BNC loop through connector. S-Video (4 pins DIN) - Y : 1Vpp ±3dB (0,7V Video +0,3V Sync) 75 Ohm termination. - U/V : 0,7Vpp ±3dB 100% color base, 75 Ohm termination. - Chroma : Multi-Standard (PAL / SECAM / NTSC). - 4 pins DIN loop through connector. AmberLED(upperLED on thefrontside)
ملخص المحتوى في الصفحة رقم 20
4. Input modules Image 4-9 Image 4-10 Order info: Article No. Description R9850940 D320 YUV / RG(s)B input module 4.6 RGB analog input module Technical info: Sub D15 connector for input and loop through. R, G, B, Hsync, Vsync : 0 to 1 Vpp ±3dB 75 Ohm termination. Black level : 300mV. Sync-tip:0V Resolution : SXGA and UXGA version available. AmberLED(upperLED on thefrontside)willbe lit indicating recognition offilm,eithercontinuousorintermittentfilm detection. When placed in an input
