Metra Electronics 95-7427G دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 95-7427
APPLICATIONS
Nissan Maxima 2009-11
w/o Navigation or Technology Package
95-7427B/
95-7427G
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• PAINTED TO MATCH FACTORY DASH:
95-7427B=BLACK, 95-7427G=GRAY
• Textured To Match Factory Dash
KIT COMPONENTS
• A) Double DIN Radio Housing
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
www.metraonline.com
1-800-221-0932
© CO

ملخص المحتوى في الصفحة رقم 2

95-7427 TABLE OF CONTENTS Dash Disassembly - Nissan Maxima 2009-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Assembly - Double DIN Radio Provision / Stacked ISO Mount Units Provision . . . .2 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most re

ملخص المحتوى في الصفحة رقم 3

CD CHANGER AUX IN PASS AIR BAG OFF 95-7427 DASH DISASSEMBLY NISSAN MAXIMA 2009-11 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Unclip and remove the panel above the radio including the a/c vents and the climate controls. Unplug and X remove the panel. (Figure A) 3 Unclip and remove the panel below the radio. (Figure B) 4 Remove (6) Phillips screws securing the radio. Unplug and remove the B radio. (Figure C) 5 Remove (5) Torx head screws secur- ing eac

ملخص المحتوى في الصفحة رقم 4

95-7427 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION OR STACKED ISO MOUNT UNIT(S) PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Attach the factory brackets and mod- A ule to the Double DIN or stacked ISO mount unit(s) with the screws supplied with the unit(s) and (2) screws from Continue to final assembly. 2

ملخص المحتوى في الصفحة رقم 5

95-7427 FINAL ASSEMBLY FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Position the factory bracket/aftermarket radio

ملخص المحتوى في الصفحة رقم 6

95-7427 NOTES 4

ملخص المحتوى في الصفحة رقم 7

95-7427 NOTES 5

ملخص المحتوى في الصفحة رقم 8

95-7427 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 10-06-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-7427