ملخص المحتوى في الصفحة رقم 1
Pub. 988-0151-401
www.lowrance.com
X96 & X96TX
Fish-finding & Depth Sounding Sonar
Installation and Operation
Instructions
ملخص المحتوى في الصفحة رقم 2
Copyright © 2005 Lowrance Electronics, Inc. All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. ® Lowrance is a registered trademark of Lowrance Electronics, Inc. Lowrance Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We rese
ملخص المحتوى في الصفحة رقم 3
Table of Contents Section 1: Read Me First!......................................................... 1 Capabilities and Specifications: X96 & X96TX ........................... 2 How Sonar Works ......................................................................... 3 How to use this manual: typographical conventions .................. 3 Arrow Keys................................................................................ 4 Keyboard .........................................................
ملخص المحتوى في الصفحة رقم 4
To adjust and turn on the shallow alarm: ......................... 40 To adjust and turn on the deep alarm: .............................. 41 Zone Alarm.............................................................................. 41 To adjust and turn on the zone alarm:............................... 41 Fish Alarm............................................................................... 42 To turn on the fish alarm:................................................... 42 Brightness .........
ملخص المحتوى في الصفحة رقم 5
Software Version Information.................................................... 62 Sonar Chart Mode....................................................................... 63 To change the chart mode scheme: ........................................ 63 Sonar Chart Display Options..................................................... 63 Full Sonar Chart..................................................................... 64 Digital Data/Chart.........................................................
ملخص المحتوى في الصفحة رقم 6
WARNING! A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSITION INFORMATION. CAUTION When showing navigation data to a position (waypoint), a GPS unit will show the shortest, most direct path to the waypoint. It provides navigation data to the waypoint regardless of obstructions. Therefore, the prudent navigator will not only take advantage of all available navigation tools when traveling to a waypoint, but will also visually check to make sure a clear, safe path to the waypoint
ملخص المحتوى في الصفحة رقم 7
Section 1: Read Me First! How this manual can get you out on the water, fast! Welcome to the exciting world of digital sonar! We know you're anxious to begin finding fish, but we have a favor to ask. Before you grab your unit and begin installing it, please give us a moment to explain how our manual can help you get the best performance from your compact, wide-screen, fish finder. First, we want to thank you for buying a Lowrance sonar. Whether you are a first time user or a professional fisherm
ملخص المحتوى في الصفحة رقم 8
If you're having difficulty with your sonar, you can find an answer to the most common problems in Section 5, Sonar Troubleshooting. Finally, in Section 6, we offer Supplemental Material, including a list of warranty and customer service information. Now, if you are into the fine details, glance over the next segment on specifications to see just how much sonar power your unit contains. It's important to us (and our power users), but, if you don't care how many watts of power the unit has, skip
ملخص المحتوى في الصفحة رقم 9
Audible alarms: ............. Deep/shallow/fish/zone. Automatic ranging:....... Yes, with instant screen updates. Zoom bottom track: ...... Yes. Split-screen zoom:......... Yes. Surface water temp: ..... Yes. Speed/distance log: ....... Optional (requires optional speed sensor). NOTICE! The storage temperature range for your unit is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Celsius). Extended storage in temperatures higher or lower than specified will damage the liqu
ملخص المحتوى في الصفحة رقم 10
The following paragraphs explain how to interpret the text formatting for those commands and other instructions: Arrow Keys The arrow keys control a horizontal line depth cursor on the sonar screen. The arrow keys also help you move around the menus so you can execute different commands. They are represented by symbols like these, which denote the down arrow key, the up arrow, the left arrow and the right arrow: ↓ ↑ ← →. Keyboard The other keys perform a variety of functions. When the text refer
ملخص المحتوى في الصفحة رقم 11
Section 2: Installation & Accessories Preparations You can install the sonar system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drilling any holes in your vessel! 1. Determine the approximate location for the sonar unit, so you can plan how and where to route the cables for the transducer and power. This will help you make sure you have enough cable length for the desired configuration. 2. D
ملخص المحتوى في الصفحة رقم 12
Remember, the transducer installation is the most critical part of a sonar installation. Recommended Tools and supplies If you prefer the option of routing the cable through the transom, you will need a 5/8" drill bit. A transom mount requires use of a high quality, marine grade above- or below-waterline caulking compound. The following installation types also call for these recommended tools and required supplies (supplies are not included): Single-frequency transom installations Tools include:
ملخص المحتوى في الصفحة رقم 13
Electrical noise from engine wiring, bilge pumps and aerators can be displayed on the sonar's screen. Use caution when routing the transducer cable around these wires. CAUTION: Clamp the transducer cable to transom near the transducer. This will help prevent the transducer from entering the boat if it is knocked off at high speed. Good location Poor location Good location Good location Poor angle Good and poor transducer locations. How low should you go? For most situations, you should install y
ملخص المحتوى في الصفحة رقم 14
If you cruise or fish around lots of structure and cover, your transducer may be frequently kicking up from object strikes. If you want, you may move the transducer a little higher for more protection. There are two extremes you should avoid. Never let the edge of the mounting bracket extend below the bottom of the hull. Never let the bottom – the face – of the transducer rise above the bottom of the hull. Shoot-thru-hull vs. Transom Mounting Typically, shoot-thru-hull installations give excelle
ملخص المحتوى في الصفحة رقم 15
Dot Align plastic ratchets in bracket. B. Two-piece bracket: Locate the four plastic ratchets in the transducer's hardware package. Press two ratchets into the sides of the plastic bracket and two on either side of the transducer as shown in the following illustrations. Notice there are letters molded into each ratchet. Place the ratchets into the bracket with the letter "A" aligned with the alignment mark molded into the bracket. Place the ratchets onto the transducer with the letter "A" aligne
ملخص المحتوى في الصفحة رقم 16
Transducer Transducer bracket Ratchet Ratchet Add ratchets to bracket and transducer. 2. Aligning the transducer on the transom. A. One-piece bracket: Slide the transducer between the two ratchets. Temporarily slide the bolt though the transducer assembly and hold it against the transom. Looking at the transducer from the side, check to see if it will adjust so that its face is parallel to the ground. If it does, then the "A" position is correct for your hull. If the transducer's face isn't para
ملخص المحتوى في الصفحة رقم 17
B. Two-piece bracket: Assemble the transducer and bracket as shown in the following figure. Temporarily slide the bolt though the transducer assembly but do not tighten the nut at this time. Hold the assembled transducer and bracket against the transom. Looking at the transducer from the side, check to see if it will adjust so its face is parallel to the ground. If it does, then the "A" positions are correct for your hull. If the transducer's face isn't parallel with the ground, remove and disas
ملخص المحتوى في الصفحة رقم 18
B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the figure in step 2B. Don't tighten the lock nut at this time. 4. Drilling mounting holes. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull! Mark the center of each slot for the mounting screw p
ملخص المحتوى في الصفحة رقم 19
Both bracket types: Attach the transducer to the transom. Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures. Tighten the bracket's mounting screws, sealing them with the caulking compound. Adjust the transducer so that it's parallel to the ground and tighten the nut until it touches the outer washer, then add 1/4 turn. Don't over tighten the lock nut! If you do, the transducer won't kick-up if it strikes an obj
ملخص المحتوى في الصفحة رقم 20
7. Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the transducer bracket down. This puts the transducer deeper into the water, hopefully below the turbulence causing the noise. Don't allow the transducer bracket to go below the bottom of the hull! TROLLING MOTOR BRACKET INSTALLATION 1. Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer