ملخص المحتوى في الصفحة رقم 1
Use & Care Guide
Model: 7116572
Char-Broil ®
FOP
Natural Gas Conversion Kit
This Natural Gas Conversion Kit can be used ONLY with
Dual Fuel™ grills.
If you have questions or need assistance during assembly, please call 1-800-241-7548 (USA) or 1-800-387-6057 (Canada)
To insure your satisfaction and for follow-up service, register your grill online at www.grillregistration.com
ملخص المحتوى في الصفحة رقم 2
WARNING DANGER CALIFORNIA PROPOSITION 65 If you smell gas: 1. Combustion by-products produced when using 1. Shut off gas to the appliance. this product contain chemicals known to the State of 2. Extinguish any open flame. California to cause cancer, birth defects, and other 3. Open lid. reproductive harm. 2. This product contains chemicals, including lead 4. If odor continues, keep away from the appliance and lead compounds, known to the State of and immediately call your gas supplier or your Ca
ملخص المحتوى في الصفحة رقم 3
CONNECTING YOUR GRILL TO THE NATURAL GAS SOURCE: TABLE OF CONTENTS 1. A professionally-installed shut-off valve between the supply piping and the socket is recommended, but not required, by Warning & Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 the National Fuel Gas Code. Socket connection must be made outdoors. Table Of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Coat the gas supply pipe nipple with gas resistant pipe
ملخص المحتوى في الصفحة رقم 4
The appliance and its individual shut off valve must be USE AND CARE CON’T. disconnected from the gas supply piping system during any pressure testing on that system at test pressures in excess of 1/2 psig (3.5kPa). The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5kPa). Figure C With proper assembly, the gas hose cannot be
ملخص المحتوى في الصفحة رقم 5
Model 415.16135110 Model 415.16649011 Model 415.16138110 415.16167210 Model 415.16139110 415.16164210 415.16139111 5 For Conversion Use Sections: A, B, F Parts Required: 5- Large Bezels 1 -10’ Hose 1-Orifice Driving Tool For Conversion Use Sections: A, B, F Parts Required: 5 -Large Bezels 1 - 10’ Hose 1 -Orifice Driving Tool For Conversion Use Sections: A, C, D, G Parts Required: 5 -Large Bezels 1 -Small Bezel 1 - 10’ Hose 1 -Orifice Driving Tool 3 - #57 Orifice (Blue Dot) 2 - #53 Orif
ملخص المحتوى في الصفحة رقم 6
Section A A1 First, make sure all Control Knobs are in the OFF position, LP tank valve is closed, and Tank is disconnected from Regulator and removed from Grill. Next, open Lid and remove Warming Rack, Cooking Grates, and Heat Diffusers. Your Grill may differ from illustrations shown. This manual covers a variety of grills styles, use pictures as reference only. Warming Rack Lid Cooking Grates (2 or 3 depending on Unit purchased) Heat Diffusers A2 Using a wrench (not provided) remove LP Regulat
ملخص المحتوى في الصفحة رقم 7
A3 Position Natural Gas Hose Assembly behind cart up to Manifold Connection. Secure the Natural Gas Hose Assembly, to Manifold Connection, using a wrench (not provided). Manifold Connection Natural Gas Hose Assembly A4 Leak Testing Natural Gas Hose Turn all grill knobs to OFF. Brush soapy solution onto areas where bubbles are shown in picture. If “growing” bubbles appear, there is a leak. Retighten connections. If leak cannot be stopped do not try to repair. Call Sears for replacement parts.
ملخص المحتوى في الصفحة رقم 8
Section B B1 Remove Hitch Pins and remove Carryover Tubes. Remove Hitch Pins at back of Burners to detach Burners from Burner Brackets. Lift back of Burner while sliding Burner out of Firebox, disengaging burners from Valves. Burner Hitch Pin Front of Firebox Hitch Pin Carryover Tube Burner B2 Insert Orifice Driving Tool into Firebox Burner openings and unscrew Orifices from ends of Valves. Save removed orifices for converting back to LP Tank Gas. These grill valves are designed to work with N
ملخص المحتوى في الصفحة رقم 9
Section B Con’t. B3 WARNING Bezels must be replaced one at a time. Removing more than one bezel at a time may cause misalignment of manifold. Pull the Tube Burner Control Knob off of Valve Stem. Remove two Screws and two Washers that secure Bezel to the Control Panel. Save removed Bezel for converting back to LP Tank Gas. Install new Natural Gas Bezel provided with Kit (see illustration below) in place of old Bezel onto Control Panel, and secure using previously removed Screws and Washers. As
ملخص المحتوى في الصفحة رقم 10
Section C C1 Remove Hitch Pins and remove Carryover Tubes. Remove Hitch Pins at back of Burners to detach Burners from Burner Brackets. Lift back of Burner while sliding Burner out of Firebox, disengaging burners from Valves. Burner Hitch Pin Front of Firebox Hitch Pin Burner Carryover Tube C2 Insert Orifice Driving Tool into Firebox Burner openings and unscrew Orifices from ends of Valves. Save removed orifices for converting back to LP Tank Gas. Do not mix with other Orifices removed from gr
ملخص المحتوى في الصفحة رقم 11
Section C Con’t. C3 Remove two Screws, two Lock Washers and two Flat Washers at the back of Searing Burner. Slide Searing Burner back and up to remove Burner. Lock Washer Screw Flat Washer Searing Burner C4 Insert Orifice Driving Tool into Firebox Burner openings and unscrew Orifice from end of Valve. Save removed orifice for converting back to LP Tank Gas. Do not mix with Orifices removed from Main Burners. Replace with Natural Gas Orifice 1.65 (Green Dot) and secure tightly to Valve. Firebox
ملخص المحتوى في الصفحة رقم 12
Section C Con’t. C5 WARNING Bezels must be replaced one at a time. Removing more than one bezel at a time may cause misalignment of manifold. Pull the Tube Burner Control Knob off of Valve Stem. Remove two Screws and two Washers that secure Bezel to the Control Panel. Save removed Bezel for converting back to LP Tank Gas. Install new Natural Gas Bezel provided with Kit (see illustration below) in place of old Bezel onto Control Panel, and secure using previously removed Screws and Washers. As
ملخص المحتوى في الصفحة رقم 13
Rotisserie Cover Section D D1 Remove Screws, Washers, and Nuts that secure Rotisserie Cover to back of grill Firebox. Remove Rotisserie Cover. Screw Flat Washer Lock Washer Nut D2 Using a wrench (not provided) remove Securing Nut from Rotisserie Connector. Slide Rotisserie Connector out from Rotisserie Burner Tube 6 Rotisserie Securing Burner Tube Nut Rotisserie Connector 13
ملخص المحتوى في الصفحة رقم 14
Orifice Orifice Driving Tool Rotisserie Connector Section D Con’t. D3 Using Orifice Driving Tool provided with Kit, unscrew Orifice from Rotisserie Connector. Save Orifice for converting back to LP Tank Gas. Do not mix with Orifices removed from Main Burners. For Grill Model 415.16649011 replace with Natural Gas Orifice 1.45mm (Red Dot) and secure tightly to Rotisserie Connector. For Grill Model 415.16139110 replace with Natural Gas Orifice #53 (Yellow Dot) and secure tightly to Rotisserie Con
ملخص المحتوى في الصفحة رقم 15
Section D Con’t. D5 Pull the Rotisserie Control Knob off of Valve Stem. Remove screws and washers that secure Bezel to the Control Panel. Save removed Bezel for converting back to LP Tank Gas. Install new Natural Gas Bezel provided with Kit (see illustration below) in place of old Bezel onto Control Panel, and secure using previously removed screws and washers. Assure proper alignment with control knob before fully tightening. Note: New bezel will change the rotation for the control knob to p
ملخص المحتوى في الصفحة رقم 16
Section E Con’t. E2 Remove two Screws at the back of Sideburner. 6 Remove Sideburner from Shelf. Screws E3 From inside the Shelf unscrew Orifice from end of Sideburner valve using the Orifice Driving Tool provided with kit. Save Orifice for converting back to LP Tank Gas. Do not mix with Orifices removed from Tube Burners. 6 DO NOT replace the Orifice. This valve is designed to work with Natural Gas once Orifice is removed. 6 Sideburner valve Orifice Orifice Driving Tool Orifice Driving Tool 5
ملخص المحتوى في الصفحة رقم 17
Section E Con’t. E4 Pull the Sideburner Control Knob off of Valve Stem. Remove the existing Bezel by removing the two Screws and two Washers securing Bezel to Shelf fascia. Save removed Bezel for converting back to LP Tank Gas. Install new Natural Gas Bezel (see illustration below) and press Control Knob back onto Valve Stem. OFF Hi Low Bezel Screw Med Valve stem Large Bezel Washer Sideburner control knob E5 Return sideburner to shelf. Make sure burner engages sideburner valve. Secure burner
ملخص المحتوى في الصفحة رقم 18
Section E Con’t. E6 Slide Sideburner Electrode into Collector Box. Secure Sideburner Electrode to Sideburner with Screw. Replace Sideburner Cooking Grate. Screw Collector box Sideburner cooking grate Sideburner Electrode Sideburner Electrode Reinstall Heat Diffusers, Cooking Grates and Warming Rack, reference illustration Section A1. for reinstallation. Section F F1 Open Sideburner Lid and remove the Sideburner Grate. From beneath Sideburner Shelf, remove Wingnut. Remove Sideburner from Shelf. S
ملخص المحتوى في الصفحة رقم 19
Orifice Orifice Driving Tool Valve Section F Con’t. F2 Using the provided Orifice Driving Tool, unscrew the Orifice from the end of the Sideburner Valve. Save removed Orifice and Orifice Driving Tool for converting back to LP. DO NOT replace the Orifice. This Valve is designed to work with Natural Gas once Orifice is removed. Orifice Driving Tool F3 Pull the Sideburner Control Knob off of Valve Stem. Remove the existing Bezel by removing the two Screws and two Washers securing bezel to Shelf
ملخص المحتوى في الصفحة رقم 20
Valve Section F Con’t. F4 Return Sideburner to Shelf. Make sure Burner engages Sideburner Valve. See illustration below for correct burner-to-valve engagement. Secure Burner to Shelf with Wingnut. Place Sideburner Grate onto Sideburner Pan. Sideburner Grate Sideburner Sideburner CORRECT BURNER-TO-VALVE ENGAGEMENT Wingnut Reinstall Heat Diffusers, Cooking Grates and Warming Rack, reference illustration Section A1. for reinstallation. Sideburner Grate Section G G1 Open Sideburner Lid and remove
